Couplings Sleeve Categories
Couplings - Sleeve Type - Hubs
0.05 to 2.1 Nm. Max Speed 1750 rpm.
Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.
Related Information:
Couplings - Sleeve Type - Sleeves
0.05 to 2.1 Nm. Max Speed 1750 rpm.
Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.
Related Information:
You may also be interested in
Couplings Geargrip
Couplings - Geargrip - Precision - Sleeves Only
Match with hubs from hubs category
Related Information:
Couplings Other
Couplings - Crowned Tooth Gear - Sleeve Only
Match with hubs from the hubs category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
Couplings Geargrip
Couplings - Geargrip - Precision - Hubs Only
Match with sleeves from sleeves category
Related Information:
Couplings Other
Couplings - Crowned Tooth Gear - Hubs Only
Match with sleeves from the sleeves category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
Couplings - Double Disk - Aluminium
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
Related Information:
Couplings - Flex Beam - Set Screw Style
Zero backlash machined from a single piece of aluminium and featuring two sets of spiral cuts.
Higher torque and reduced windup compared to commodity type single beam couplings.
Couplings - Helical - Economy
Low cost aluminium couplings primarily used for 3D printer stepper motors
Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.
Related Information:
Couplings - Helical - Standard
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.
Related Information:
Couplings - Reli-a-flex - Long Series - Clamp Type
From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).
Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.
Related Information:
Couplings - Reli-a-flex - Short Series - Clamp Type
From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).
Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.
Related Information:
Couplings - Reli-a-flex - Short Series - Set Screw Type
From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).
Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.
Related Information:
Couplings - Slit Type - Standard
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
Related Information:
Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type
Pilot Bore size not toleranced. Finished Bore sizes to +0.03/0.00.
Related Information:
Couplings - Oldham - Disks for Clamp Style
0.06 to 44 Nm. Max Speed: 3000 RPM.
Disk inserts. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Related Information:
Couplings - Oldham - Hubs - Clamp Style
0.06 to 44 Nm. Max Speed: 3000 RPM.
Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Related Information:
Couplings - Spider Type B - Hubs Only
Match 2 hubs with a spider from the spiders category. Match only rubber spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Metal hubs to suit rubber spiders type B.
Related Information:
Couplings - Spider Type C - Complete
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm. Match only hubs and spiders from listings SPIDER TYPE C. Inserts are held between the jaws of two hubs.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application. Polyurethane spider.
Related Information:
Couplings - Spline Type - Complete
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.
Related Information:
Couplings - Spline Type - Spare Hubs
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.
Related Information:
Couplings - Spline Type - Spare Poyurethane Splines
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.
Related Information:
Couplings - Three Jaw Type - Hubs
Match with Three Jaw Type inserts by OD. Two Hubs and one insert will be needed to make a complete coupling.
Complete with keyway and set screw. No lubrication needed.
Related Information:
Couplings - Three Jaw Type - Inserts
Match with Three Jaw Type hubs by OD
Use Bost-Bronz inserts for high torque loads at slower speeds. Use rubber for quiter operation. Use polyurethane for moderate to heavy shock loads.
Related Information:
Couplings - Neo-Flex
0.71 to 1.27 Nm.
303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.
Related Information:
Couplings - Rigid - 1 Piece Clamp - Stainless Steel
303 Grade Stainless
Precision Machined. High torsional load. Non marring, easy to install and adjust. Use on hardened shafts, rigid clamp type design, easily machinable. Available with stepped bores and keyways on 5 week delivery.
Couplings - Rigid - 2 Piece Clamp - Steel
12L14 Steel
Precision Machined. High torsional load. Non marring, easy to install and adjust. Assemble without moving shafts. Use on hardened shafts, rigid clamp type design, easily machinable. Black finish with alloy steel cap screws. Available with stepped bores and keyways on 5 week delivery.
Couplings - Rigid - Hobby - Brass
A selection of inexpensive brass couplings for shaft sizes from 2 to 5 mm.
Related Information:
Couplings - Rigid - Set Screw
0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000.
Related Information:
465LRN Coupling Kavo Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Shafts - Flexible - Coupling Ends - Open - Mild Steel
Flexible shafting with coupling ends ready to attach to a fixed shaft.
1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm.
Related Information:
Spacers - Hex - Threaded - Brass
Threaded Hex Spacers. Also known as coupling nuts.
Most items are nickel plated. Refer details recorded against each item.
Spacers - Hex - Threaded - Steel
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Spacers - Hex - Threaded - 316 Stainless Steel
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Spacers - Hex - Threaded - 303-304 Stainless Steel
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Shafting - Ground - Hobby - Steel
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc. Not recommended for use with precision steel or stainless steel bearings. Some sizes have special features such as serrations or small barbs (noted in description). Unground ends. Ideal for axles in robotic applications and educational projects.
Related Information:
Sleeves - Hex Hole - Carbon Steel
Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.
Sleeves - Hex Hole - Hardened
Pre hardened to Rockwell 23-30C. Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.
Sleeves - Square Hole - Plain - Carbon Steel
Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.
Sleeves - Square Hole - Plain - Hardened
Pre hardened to Rockwell 23-30C. Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.
Sleeves - Square Hole - Threaded - Carbon Steel
Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through and threaded internally at one end.
Shaftloc-tm Sleeves - Single Ended
Simple effective way to lock components onto shafts.
416 Stainless Steel. Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened.
Related Information:
Attachments - Cable - Loop Sleeves
Use with synchromesh or standard miniature cable
Related Information:
Attachments - Cable - Stop Sleeves
Use with synchromesh or standard miniature cable. Use a swaging tool to compress the stop sleeve over the end of the cable.
Related Information:
Sleeving - Mesh
Low cost protection for threaded and cylindrical parts
Elastic snug tight fit protective sleeve fits over straight, tapered or contoured parts. Made from polyethylene. Thickness of web approx 1.8mm. Sold per foot (300mm). Maximum contunuous roll is 100 feet (30 mtrs).
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Contact Us
Charity
Dental Bearings
Dowel Pins
Downloadable PDF Catalogue Ball Lock Pins
Downloadable PDF Catalogue Balls
Downloadable PDF Catalogue Ceramic Bearings
Downloadable PDF Catalogue Circlips
Downloadable PDF Catalogue Clevis Pins
Downloadable PDF Catalogue Corrosion Resistant Bearings
Downloadable PDF Catalogue Disc Springs
Downloadable PDF Catalogue Dowel Pins
Downloadable PDF Catalogue Economy Bearings
Downloadable PDF Catalogue Hammer Drive Pins
Downloadable PDF Catalogue High Speed Bearings
Downloadable PDF Catalogue Key Steel
Downloadable PDF Catalogue Knobs
Downloadable PDF Catalogue Leveling Mounts
Downloadable PDF Catalogue Metallic Bushes
Downloadable PDF Catalogue O-Rings
Downloadable PDF Catalogue Pins
Downloadable PDF Catalogue Plastic Bearings
Downloadable PDF Catalogue Polyvee Belts and Pulleys
Downloadable PDF Catalogue Precision Shim Washers
Downloadable PDF Catalogue Push On and Push In Rings
Downloadable PDF Catalogue Rod & Tube
Downloadable PDF Catalogue Roll Pins
Downloadable PDF Catalogue Shaft Collars
Downloadable PDF Catalogue Shim Sheet
Downloadable PDF Catalogue Shoulder Screws
Downloadable PDF Catalogue Sintered Bronze Bushes
Downloadable PDF Catalogue Snap Rings
Downloadable PDF Catalogue Socket Set Screws
Downloadable PDF Catalogue Solid Bronze Bushes
Downloadable PDF Catalogue Spring Steel Strip
Downloadable PDF Catalogue Springs
Downloadable PDF Catalogue Standard Ball Bearing Range
Downloadable PDF Catalogue Super Precision Bearings
Downloadable PDF Catalogue Taper Pins
Downloadable PDF Catalogue Thrust Bearings
Downloadable PDF Catalogue Thumb Screws and Nuts
Downloadable PDF Catalogue Timing Belts
Downloadable PDF Catalogue Timing Pulley Stock
Downloadable PDF Catalogue Timing Pulleys
Downloadable PDF Catalogue Vibration Mounts
Downloadable PDF Catalogue Washers
Downloadable PDF Catalogue Wave Washers
Downloadable PDF Cross Reference ADR and SKF
Downloadable PDF Cross Reference Anderton Circlips
Downloadable PDF Cross Reference Barden Bearings
Downloadable PDF Cross Reference Essentra
Downloadable PDF Cross Reference Flocast
Downloadable PDF Cross Reference K&S Metals
Downloadable PDF Cross Reference McMaster Carr
Downloadable PDF Cross Reference Miniature Precison Bearings
Downloadable PDF Cross Reference Nordex
Downloadable PDF Cross Reference NSK and NTN
Downloadable PDF Cross Reference Ondrives
Downloadable PDF Cross Reference Reid Supply
Downloadable PDF Cross Reference SDP-SI Designatronics
Downloadable PDF Cross Reference Seeger Circlips
Downloadable PDF Cross Reference Sintered Bronze
Downloadable PDF Cross Reference Small Parts Inc
Downloadable PDF Cross Reference Timing Belts and Pulleys
Freight Rates and Shipping Times
Frequently Asked Questions
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 131241 products in 2170 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
