Couplings Other


Couplings - BoWex - Junior
Couplings - BoWex - Junior

Nylon 2 piece and 3 piece couplings. 5 to 24 Nm. 6000 rpm max.

Approved distribution through the Australian Wholesaler (Deanquip). Crowned gear teeth - No need for lubrication. Chemical resistant nylon. Electrically insulated. Grub Screw opposite Keyway.

Related Information:
Shafting

Couplings - Eccentric Drive
Couplings - Eccentric Drive

1.88mm bore press fits most standard hobby motors (2mm shaft)


If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Couplings - Eccentric Drive.

Couplings - Neo-Flex
Couplings - Neo-Flex

0.71 to 1.27 Nm.

303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.

Related Information:
Shafting

Couplings - Crowned Tooth Gear - Hubs Only
Couplings - Crowned Tooth Gear - Hubs Only

Match with sleeves from the sleeves category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:
Sleeves To Suit
Shafting

Couplings - Crowned Tooth Gear - Sleeve Only
Couplings - Crowned Tooth Gear - Sleeve Only

Match with hubs from the hubs category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:
Hubs to Suit
Shafting

Dubro Accessories


Dubro Accessories Listed by Description
Dubro Accessories Listed by Description

Accessories for model airplanes and other hobbies.

Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings,. Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns,. Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws,. Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders,. Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.


If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Dubro Accessories Listed by Description.

Dental Handpiece Parts


Coupling - Multiflex Kavo Parts
Coupling - Multiflex Kavo Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Coupling - Multiflex Kavo Parts.

Couplings Bellows


Couplings - Bellows - Set Screw - 316 Stainless
Couplings - Bellows - Set Screw - 316 Stainless

Also see combined categories:
All Bellows Couplings

Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics

Stainless Steel 303L Bellows. Stainless Steel 316 Hubs.

Related Information:
Shafting

Couplings Disk


Couplings - Double Disk - Aluminium
Couplings - Double Disk - Aluminium

Zero Backlash - High Torsional Stiffness.

Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.

Related Information:
Techical Details
Shafting

Couplings Geargrip


Couplings - Geargrip - Precision - Hubs Only
Couplings - Geargrip - Precision - Hubs Only

Match with sleeves from sleeves category

Related Information:
Precision Geargrip Sleeves

Couplings - Geargrip - Precision - Sleeves Only
Couplings - Geargrip - Precision - Sleeves Only

Match with hubs from hubs category

Related Information:
Precision Geargrip Hubs

Couplings Helical and Slit


Couplings - Flex Beam - Clamp Style
Couplings - Flex Beam - Clamp Style

Also see combined categories:
All Helical and Slit Couplings

Zero backlash machined from a single piece of aluminium and featuring two sets of spiral cuts.

Higher torque and reduced windup compared to commodity type single beam couplings.


Couplings - Flex Beam - Set Screw Style
Couplings - Flex Beam - Set Screw Style

Also see combined categories:
All Helical and Slit Couplings

Zero backlash machined from a single piece of aluminium and featuring two sets of spiral cuts.

Higher torque and reduced windup compared to commodity type single beam couplings.


Couplings - Helical - Economy
Couplings - Helical - Economy

Also see combined categories:
All Helical and Slit Couplings

Low cost aluminium couplings primarily used for 3D printer stepper motors

Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.

Related Information:
Helical Couplings Selection Guide
Shafting

Couplings - Helical - Long Series
Couplings - Helical - Long Series

Also see combined categories:
All Helical and Slit Couplings

2.9 to 31.4 Nm.

5o max angular misalignment. 0.762 mm Parallel offset. +/- 0.254 mm Axial motion. Zero backlash.

Related Information:
Helical Couplings Selection Guide
Shafting

Couplings - Helical - Low Inertia
Couplings - Helical - Low Inertia

Also see combined categories:
All Helical and Slit Couplings

0.8 to 13.2 Nm.

5o max angular misalignment. 0.254 mm Parallel offset. +/- 0.203 mm Axial motion. Zero backlash.

Related Information:
Helical Couplings Selection Guide
Shafting

Couplings - Helical - Precision
Couplings - Helical - Precision

Also see combined categories:
All Helical and Slit Couplings

0.14 to 9 Nm. 25000 max RPM.

5o max angular misalignment. 0.076 mm Parallel offset. Zero Axial motion. Zero backlash.

Related Information:
Helical Couplings Selection Guide
Shafting

Couplings - Helical - Short - Ondrives
Couplings - Helical - Short - Ondrives

Also see combined categories:
All Helical and Slit Couplings

Material: 303 S3U Stainless.

Related Information:
Shafting

Couplings - Helical - Standard
Couplings - Helical - Standard

Also see combined categories:
All Helical and Slit Couplings

0.1 to 16.2 Nm.

Zero backlash. Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.

Related Information:
Helical Couplings Selection Guide
Shafting

Couplings - Reli-a-flex - Long Series - Clamp Type
Couplings - Reli-a-flex - Long Series - Clamp Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:
Shafting

Couplings - Reli-a-flex - Short Series - Clamp Type
Couplings - Reli-a-flex - Short Series - Clamp Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:
Shafting

Couplings - Reli-a-flex - Short Series - Set Screw Type
Couplings - Reli-a-flex - Short Series - Set Screw Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:
Shafting


Couplings - Slit Type - Standard
Couplings - Slit Type - Standard

Also see combined categories:
All Helical and Slit Couplings

Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.

High Torsional Stiffness. Zero Backlash.

Related Information:
Shafting

Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type
Couplings - Spiral Beam - 6 Beam - Aluminium - Set Screw Type

Also see combined categories:
All Helical and Slit Couplings

Pilot Bore size not toleranced. Finished Bore sizes to +0.03/0.00.

Related Information:
Shafting

Couplings Insert and Jaw


Couplings - HRC
Couplings - HRC

Also see combined categories:
All Insert and Jaw Type Couplings

Related Information:
Shafting

Couplings - Oldham - Complete - Acetal Disk - Set Screw
Couplings - Oldham - Complete - Acetal Disk - Set Screw

Also see combined categories:
All Insert and Jaw Type Couplings

0.06 to 44 Nm. Max Speed: 3000 RPM.

Max Speed: 3000 RPM. Parallel out of line compensation. Temp Range -20 oC to +60 oC. Oldham couplings are designed to transfer torque between two parallel, but not colinear, shafts. They have three discs, one coupled to the input, one coupled to the output, and a centre disc that is joined to the first two by tongue and grooves. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:
Shafting

Couplings - Oldham - Disks for Clamp Style
Couplings - Oldham - Disks for Clamp Style

Also see combined categories:
All Insert and Jaw Type Couplings
All Oldham Disks

0.06 to 44 Nm. Max Speed: 3000 RPM.

Disk inserts. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:
Hubs to suit clamp style disks
Shafting

Couplings - Oldham - Hubs - Clamp Style
Couplings - Oldham - Hubs - Clamp Style

Also see combined categories:
All Insert and Jaw Type Couplings
All Oldham Hubs

0.06 to 44 Nm. Max Speed: 3000 RPM.

Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.

Related Information:
Disk Inserts for Clamp Style
Shafting

Couplings - Spider Type B - Complete
Couplings - Spider Type B - Complete

Also see combined categories:
All Insert and Jaw Type Couplings

Max 3600 RPM. 0.39 to 16.27 Nm. Match only hubs and spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.

Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Rubber spider and metal hubs.

Related Information:
Replacement Spiders To Suit
Shafting
Replacement Hubs To Suit

Couplings - Spider Type B - Hubs Only
Couplings - Spider Type B - Hubs Only

Match 2 hubs with a spider from the spiders category. Match only rubber spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.

Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Metal hubs to suit rubber spiders type B.

Related Information:
Spiders To Suit
Shafting
Complete Couplings

Couplings - Spider Type C - Complete
Couplings - Spider Type C - Complete

Also see combined categories:
All Insert and Jaw Type Couplings

Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm. Match only hubs and spiders from listings SPIDER TYPE C. Inserts are held between the jaws of two hubs.

Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application. Polyurethane spider.

Related Information:
Replacement Spiders To Suit
Shafting

Couplings - Spline Type - Complete
Couplings - Spline Type - Complete

Also see combined categories:
All Insert and Jaw Type Couplings

0.5 to 4.5 Nm. 12000 to 24000 rpm.

Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.

Related Information:
Shafting

Couplings - Spline Type - Spare Hubs
Couplings - Spline Type - Spare Hubs

Also see combined categories:
All Insert and Jaw Type Couplings

0.5 to 4.5 Nm. 12000 to 24000 rpm.

Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.

Related Information:
Shafting

Couplings - Spline Type - Spare Poyurethane Splines
Couplings - Spline Type - Spare Poyurethane Splines

Also see combined categories:
All Insert and Jaw Type Couplings

0.5 to 4.5 Nm. 12000 to 24000 rpm.

Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.

Related Information:
Shafting

Couplings - Three Jaw Type - Hubs
Couplings - Three Jaw Type - Hubs

Match with Three Jaw Type inserts by OD. Two Hubs and one insert will be needed to make a complete coupling.

Complete with keyway and set screw. No lubrication needed.

Related Information:
Inserts

Couplings - Three Jaw Type - Inserts
Couplings - Three Jaw Type - Inserts

Match with Three Jaw Type hubs by OD

Use Bost-Bronz inserts for high torque loads at slower speeds. Use rubber for quiter operation. Use polyurethane for moderate to heavy shock loads.

Related Information:
Hubs

Couplings K Type


Couplings - K Type
Couplings - K Type

Up to 3600 RPM - Minus 20 to Plus 60o C. 0.34 to 18 Nm.

Strong, flexible polyurethane or Hyrtel(R) is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60o C / Hyrtel(R) : Minus 40 to Plus 100o C. Precision swaged mechanically crimped hubs. Annealed steel hubs.

Related Information:
Shafting

Couplings Rigid



Couplings - Rigid - 1 Piece Clamp - Stainless Steel
Couplings - Rigid - 1 Piece Clamp - Stainless Steel

Also see combined categories:
All Rigid Couplings

303 Grade Stainless

Precision Machined. High torsional load. Non marring, easy to install and adjust. Use on hardened shafts, rigid clamp type design, easily machinable. Available with stepped bores and keyways on 5 week delivery.



Couplings - Rigid - 2 Piece Clamp - Steel
Couplings - Rigid - 2 Piece Clamp - Steel

Also see combined categories:
All Rigid Couplings

12L14 Steel

Precision Machined. High torsional load. Non marring, easy to install and adjust. Assemble without moving shafts. Use on hardened shafts, rigid clamp type design, easily machinable. Black finish with alloy steel cap screws. Available with stepped bores and keyways on 5 week delivery.


Couplings - Rigid - Hobby - Brass
Couplings - Rigid - Hobby - Brass

Also see combined categories:
All Rigid Couplings

A selection of inexpensive brass couplings for shaft sizes from 2 to 5 mm.

Related Information:
Shafting

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Couplings - Rigid - Hobby - Brass.

Couplings - Rigid - Set Screw
Couplings - Rigid - Set Screw

Also see combined categories:
All Rigid Couplings

0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.

Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000.

Related Information:
Shafting

Couplings Sleeve


Couplings - Sleeve Type - Hubs
Couplings - Sleeve Type - Hubs

0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:
Sleeves To Suit Sleeve Type Hubs
Shafting

Couplings - Sleeve Type - Sleeves
Couplings - Sleeve Type - Sleeves

0.05 to 2.1 Nm. Max Speed 1750 rpm.

Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.

Related Information:
Hubs to Suit Sleeve Type Couplings
Shafting

Dental Handpiece Parts


Multiflex Coupling Kavo Parts
Multiflex Coupling Kavo Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Multiflex Coupling Kavo Parts.

Flexible Shaft


Shafts - Flexible - Coupling Ends - Open - Mild Steel
Shafts - Flexible - Coupling Ends - Open - Mild Steel

Also see combined categories:
All Coupling End Flexible Shaft

Flexible shafting with coupling ends ready to attach to a fixed shaft.

1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm.

Related Information:
Performance Data
Remote Control Nomenclature

Spacers


Spacers - Hex - Threaded - Aluminium
Spacers - Hex - Threaded - Aluminium

Also see combined categories:
All Threaded Hex Spacers

Threaded Hex Spacers. Also known as coupling nuts.



Show all items starting with
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   1   2   3   4   5   6   7   8   9  




Other Store Pages

Click Page Banner Below

Top

Main Pages

Click Page Banner Below

Top






Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 126266 products in 2937 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts and Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.