Match with sleeves from sleeves category
Related Information:
Match with hubs from hubs category
Related Information:
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Stainless Steel 303L Bellows. Stainless Steel 316 Hubs.
Related Information:
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
Related Information:
Zero backlash machined from a single piece of aluminium and featuring two sets of spiral cuts.
Higher torque and reduced windup compared to commodity type single beam couplings.
Low cost aluminium couplings primarily used for 3D printer stepper motors
Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.
Related Information:
2.9 to 31.4 Nm.
5o max angular misalignment. 0.762 mm Parallel offset. +/- 0.254 mm Axial motion. Zero backlash.
Related Information:
0.8 to 13.2 Nm.
5o max angular misalignment. 0.254 mm Parallel offset. +/- 0.203 mm Axial motion. Zero backlash.
Related Information:
0.14 to 9 Nm. 25000 max RPM.
5o max angular misalignment. 0.076 mm Parallel offset. Zero Axial motion. Zero backlash.
Related Information:
Material: 303 S3U Stainless.
Related Information:
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.
Related Information:
From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).
Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.
Related Information:
From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).
Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.
Related Information:
From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).
Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.
Related Information:
Aluminium - Flexible.
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
Related Information:
Pilot Bore size not toleranced. Finished Bore sizes to +0.03/0.00.
Related Information:
Related Information:
0.06 to 44 Nm. Max Speed: 3000 RPM.
Max Speed: 3000 RPM. Parallel out of line compensation. Temp Range -20 oC to +60 oC. Oldham couplings are designed to transfer torque between two parallel, but not colinear, shafts. They have three discs, one coupled to the input, one coupled to the output, and a centre disc that is joined to the first two by tongue and grooves. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Related Information:
0.06 to 44 Nm. Max Speed: 3000 RPM.
Disk inserts. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Related Information:
0.06 to 44 Nm. Max Speed: 3000 RPM.
Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Related Information:
Max 3600 RPM. 0.39 to 16.27 Nm. Match only hubs and spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Rubber spider and metal hubs.
Related Information:
Match 2 hubs with a spider from the spiders category. Match only rubber spiders from listings SPIDER TYPE B. Insert is set between the jaws of two hubs.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM. Metal hubs to suit rubber spiders type B.
Related Information:
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm. Match only hubs and spiders from listings SPIDER TYPE C. Inserts are held between the jaws of two hubs.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application. Polyurethane spider.
Related Information:
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.
Related Information:
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.
Related Information:
0.5 to 4.5 Nm. 12000 to 24000 rpm.
Maximum parallel offset 0.2mm, Maximum working angle 2 Deg. High RPM. No Lubrication. Electrically Isolated. Dampens Shock & Vibration. Operating temperature -30 to 100 oC.
Related Information:
Match with Three Jaw Type inserts by OD. Two Hubs and one insert will be needed to make a complete coupling.
Complete with keyway and set screw. No lubrication needed.
Related Information:
Match with Three Jaw Type hubs by OD
Use Bost-Bronz inserts for high torque loads at slower speeds. Use rubber for quiter operation. Use polyurethane for moderate to heavy shock loads.
Related Information:
Up to 3600 RPM - Minus 20 to Plus 60o C. 0.34 to 18 Nm.
Strong, flexible polyurethane or Hyrtel(R) is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60o C / Hyrtel(R) : Minus 40 to Plus 100o C. Precision swaged mechanically crimped hubs. Annealed steel hubs.
Related Information:
Nylon 2 piece and 3 piece couplings. 5 to 24 Nm. 6000 rpm max.
Approved distribution through the Australian Wholesaler (Deanquip). Crowned gear teeth - No need for lubrication. Chemical resistant nylon. Electrically insulated. Grub Screw opposite Keyway.
Related Information:
Match with sleeves from the sleeves category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
Match with hubs from the hubs category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
1.88mm bore press fits most standard hobby motors (2mm shaft)
0.71 to 1.27 Nm.
303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.
Related Information:
303 Grade Stainless
Precision Machined. High torsional load. Non marring, easy to install and adjust. Use on hardened shafts, rigid clamp type design, easily machinable. Available with stepped bores and keyways on 5 week delivery.
12L14 Steel
12L14 Steel
Precision Machined. High torsional load. Non marring, easy to install and adjust. Assemble without moving shafts. Use on hardened shafts, rigid clamp type design, easily machinable. Black finish with alloy steel cap screws. Available with stepped bores and keyways on 5 week delivery.
A selection of inexpensive brass couplings for shaft sizes from 2 to 5 mm.
Related Information:
0.35 to 5.1 Nm. Includes steel, stainless steel, brass and aluminium.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000.
Related Information:
0.05 to 2.1 Nm. Max Speed 1750 rpm.
Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.
Related Information:
0.05 to 2.1 Nm. Max Speed 1750 rpm.
Polyethylene Sleeve. Acetal hub. Aluminium Alloy Insert.
Related Information:
Flexible shafting with coupling ends ready to attach to a fixed shaft.
1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm.
Related Information:
Threaded Hex Spacers. Also known as coupling nuts.
Threaded Hex Spacers. Also known as coupling nuts.
Most items are nickel plated. Refer details recorded against each item.
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Threaded Hex Spacers. Also known as coupling nuts, joiner or connector.
Small light weight geared motors used in toys and small solar applications
NOTE! These do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
Compact economical Posi Drive Stages take the work out of designing linear motion control systems.
These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 125482
products in 2754 categories including
ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.