Clutches
Multiplate Design.
Fully adjustable within rating limits. Low stick / slip ratio. Continuous slip within dissipation limit. Zinc plated steel housing with brass plates. Proprietary non-asbestos friction material.
Related Information:
Requires no power.
Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page.
Related Information:
Requires no power.
Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page.
Related Information:
Ultrafast Responses.
The input shaft becomes coupled to the output shaft with electrical excitation. Shafts have a flat on the end. Soft or fast start.
Related Information:
Taper Gears - Weight: 1.50kg. TG112 Series.
Case: Anodised Aluminum 6082. Taper Gears: 817M40T High Carbon Steel. Weight: 1.50kg. Output Backlash: Less than 8.1 arc/min at output. Max Input Speed: 3000 Rpm.
Related Information:
NT121 Series.
Case: Aluminium, Gear: 655M13 Hardened. Weight: 2.6/4.0kg, Backlash: Depends on ratio. Max Input Speed: 3000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
NTB121 Series.
Case: Aluminium, Gear: 655M13 Hardened. Weight: 1.63/3.0kg, Backlash: Depends on ratio. Max Input Speed: 3000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
NT122 Series.
Case: Aluminium, Gear: 655M13 Hardened. Weight: 2.6/4.0kg, Backlash: Depends on ratio. Max Input Speed: 3000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
NTB122 Series.
Case: Aluminium, Gear: 655M13 Hardened. Weight: 4/5kg, Backlash: Depends on ratio. Max Input Speed: 3000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
J27 Series. Miniature gearbox.
Case: Aluminium. Gear: Stainless Steel 303S21/31. Bearing: 440C. Weight: 60g. Backlash: Depends on ratio. Hours Life: 12000 hr. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
J51 Series.
End Caps: AA15 Red Anodised Aluminum (6082-T6). Centre Body: Black Delrin. Gears: High Carbon Steel 817M40(EN24). Weight: 0.14kg. Output Backlash: 3o - 6o. Approx Motion: J51-10 = 2o30' on output. Max Input Speed: 4000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
J52 Series.
End Caps: AA15 Red Anodised Aluminum (6082-T6). Centre Body: Black Delrin. Gears: High Carbon Steel 817M40(EN24). Weight: 0.14kg. Backlash: Depends on ratio. Max Input Speed: 4000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
JHD51 Series.
Case: Aluminium. Gear: Stainless Steel 303S21/31. Bearing: 440C. Gears: High Carbon Steel 817M40(EN24). Weight: 0.14kg. Output Backlash: 3o - 6o. Approx Motion: JHD51-10 = 2o30' on output. Max Input Speed: 4000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
J53 Series.
Case: Aluminium. Gear: Stainless Steel 303S21/31. Bearing: 440C. Weight: 0.14kg. Backlash: Depends on ratio. Max Input Speed: 4000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
NT61 Series.
Case: Aluminium, Gear: 655M13 Hardened. Weight: 0.6/1.2kg, Backlash: Depends on ratio. Max Input Speed: 3000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
NT62 Series.
Case: Aluminium, Gear: 655M13 Hardened. Weight: 0.6/1.2kg. Backlash: Depends on ratio. Max Input Speed: 3000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
NT63 Series.
Case: Aluminium, Gear: 655M13 Hardened. Weight: 0.6/1.2kg. Backlash: Depends on ratio. Max Input Speed: 3000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
J64 Series.
End Caps: Aluminium. Centre Body: Black Delrin. Gear: 817M40 (EN24). Weight: 0.3kg. Backlash: Depends on ratio. Max Input Speed: 4000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
J65 Series.
End Caps: AA15 Red Anodised Aluminum (6082-T6). Centre Body: Black Delrin. Gears: High Carbon Steel 817M40(EN24). Weight: 0.3kg. Backlash: Depends on ratio. Max Input Speed: 4000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
J66 Series.
End Caps: AA15 Red Anodised Aluminum (6082-T6). Centre Body: Black Delrin. Gears: High Carbon Steel 817M40(EN24). Weight: 0.3kg. Backlash: Depends on ratio. Max Input Speed: 4000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
NT91 Series.
Case: Aluminium, Gear: 655M13 Hardened. Weight: 2.6/4.0kg. Backlash: Depends on ratio. Max Input Speed: 3000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
NT92 Series.
Case: Aluminium, Gear: 655M13 Hardened. Weight: 2.6/4.0kg. Backlash: Depends on ratio. Max Input Speed: 3000 Rpm. Lubrication: Greased for life - Shell Nerita Grease HV. Testing in your applications is necessary. Torque figures are to be used for guidance only.
Related Information:
Servo Gearbox 35Nm to 50Nm ratios 9:1 - 36:1. EHD08 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Gears: Steel EN36 655M13 EN24T 817M40T. Weight: 2.1kg Backlash: 1o30'. Max Input Speed: 4,000 Rpm (short term). Lubrication: Greased for life - Shell Nerita Grease HV.
Related Information:
Servo Gearbox 60Nm to 140Nm ratios 3:1 - 6:1. EHD12 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Gears: Steel EN36 655M13 EN24T 817M40T. Backlash: 30'. Max Input Speed: 3,000 Rpm (short term). Lubrication: Greased for life - Shell Nerita Grease HV.
Related Information:
Servo Gearbox 180Nm to 380Nm ratios 3:1 - 6:1. EHD16 Series.
Case: Steel. Gears: Steel EN36 655M13 EN24T 817M40T. Weight: 18.86kg Backlash: 30'. Max Input Speed: 2,000 Rpm (short term). Lubrication: Greased for life - Shell Nerita Grease HV.
Related Information:
Servo Gearbox 3.4Nm to 7Nm ratios 3:1 - 6:1. EHD04 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Gears: Steel EN36 655M13 EN24T 817M40T. Weight: 0.44kg Backlash: 30'. Max Input Speed: 4,000 Rpm (short term). Lubrication: Greased for life - Shell Nerita Grease HV.
Related Information:
Servo Gearbox 8Nm to 19Nm ratios 3:1 - 6:1. EHD06 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Gears: Steel EN36 655M13 EN24T 817M40T. Weight: 0.96kg Backlash: 30'. Max Input Speed: 4,000 Rpm (short term). Lubrication: Greased for life - Shell Nerita Grease HV.
Related Information:
Servo Gearbox 20Nm to 50Nm ratios 3:1 - 6:1. EHD08 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Gears: Steel EN36 655M13 EN24T 817M40T. Weight: 1.4kg Backlash: 30'. Max Input Speed: 4,000 Rpm (short term). Lubrication: Greased for life - Shell Nerita Grease HV.
Related Information:
Use with NEMA Size 17 Motors.
Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 oC (-65 to 250 Deg F).
Related Information:
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
1144 steel heat treated to 53-57 RC.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. Knurled shoulder. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
1144 steel heat treated to 53-57 RC. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
440C Stainless Steel heat treated to 55-58 RC.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
1144 steel heat treated to 53-57 RC.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. Knurled shoulder. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
1144 steel heat treated to 53-57 RC. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.
Related Information:
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.
Designed to guide, position, and support the cutting tool in a metalworking jig.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Joinable belting. 88 Shore A hardness. Yellow colour. Temperature range -31 to 65 Deg C (-25 to 150 Deg F).
Join with Rounthane Connectors (purchased separately). Material : Non Slip Polyurethane. Use with grooved idler pulleys with diameters at least 8 times the belt width. Purchased per 305mm (1 foot). Orders for more than 1 foot will be supplied as a continuous length. FDA / USDA approved.
Related Information:
Applies quickly and easily wherever protection is needed against nicks, scratches, scuffs and slippage.
Sold per pad - see quantity per pad in data for each item.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 125482
products in 2754 categories including
ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.