Delays on shipments from USA and shipments passing through Singapore
Shipments from the USA are currently experiencing delays due to severe weather conditions. Shipments passing through Singapore are experiencing some minor delays due to Covid restrictions. We will keep you updated if your orders are affected.
CLIPS CATEGORIES
Rings - Crescent
Variation of an E-Clip with an open face. Also known as a C-Clip.
Narrow section height provides good clearance capabilities. Absence of teeth and deep set mean less thrust load ratings than e-clips. For best results install using the recommended applicator tool.
Related Information:
Snap Rings - External - Basic
Includes series M3200 / SP / ESP / M2400 / SW snaprings. Similar to a circlip without the lugs.
Carbon sping steel. Used on the outside diameter of a bearing, shaft or similar equipment.
Snap Rings - Internal - Basic
M2300 / SB / ESB Snaprings. Like an internal circlip without the lugs.
Applications include gear systems, securing needle bearings and to act as spacers. Used on the inside bore diameter of a housing or similar.
R Clips - Single Coil - Stainless Steel
Also known as internal hitch pins, bridge pins or humpback pins
Snap Rings - Internal - Stainless Steel
Internal snaprings are similar to an internal circlip without the lugs
301 S11/S22 Stainless Steel. Used on the inside bore diameter of a housing or similar.
Push In Retaining Rings - Carbon Steel
Thrust load shown is calculated for ideal conditions with mild steel bore.
Push On Retaining Rings - Carbon Steel
M1465 / DTX / Seeger ZA and KS.
Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested.
Push On Retaining Rings - Stainless Steel
Rotor Clip TY. Stainless Steel hardness HR15N 82.5-86
PH 15-7/17-7 Stainless Steel and 1.4310 Stainless Steel.
Bushes - Plastic - Clip - Bevelled Edge
M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F). Used as a light duty split bearing.
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight.
Related Information:
Bushes - Plastic - Clip - Double Flanged
For use with sheet metal. Used as a light duty split bearing.
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40 oC to 80 oC (minus 40 Deg F to 176 Deg F).
Related Information:
Attachments - Wire Rope Clips - Carbon Steel
Hot galvanised carbon steel
Furnished with hex nuts. Meet USA Fed. Spec. FF-C-450c, Type I, Class 1.
Attachments - Wire Rope Clips - Stainless Steel
304 Stainless Steel
Furnished with hex nuts. Meet USA Fed. Spec. FF-C-450c, Type I, Class 1.
Joints - Clevis - Spring Clips
Clips only, joints ordered separately. Made from 9SMn steel. Used like a clevis pin but with a clip to hold them to the body of the clevis joint. Check clevis joint body size for suitability.
Steel 9 SMn 28K (550-700 N/mm2). See also yokes.
Related Information:
Joints - Clevis - Plastic
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
Snap Buttons - Double End
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
Snap Buttons - Flat Type
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
Snap Buttons - Single End - Dog Leg
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
Snap Buttons - Single End - Spring Leg
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
Accessories - Hobby - Car and Buggy
Generic Parts. Specific model parts may also be found by typing the model number into the search box. Fail safes, aerials, heat sinks, body clips, tune pipe, clutch bell, bump start, engine break stand, engine fans, antenna tubes and tire warmers.
Includes Kyosho pull starts.
E-Clips - Basic - Berrylium Copper
Basic imperial and metric e-clips DIN6799 and N1500. Berrylium Copper.
Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip.
Related Information:
E-Clips - Basic - Stainless Steel
Basic imperial and metric e-clips DIN6799 and N1500. Stainless Steel PH15-7 Mo.
Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip.
Related Information:
E-Clips - Basic - Carbon Steel
Basic imperial and metric e-clips DIN6799 and N1500. Carbon spring steel including zinc plated and plain.
Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip. Includes plain and zinc plated.
Related Information:
Dubro Accessories Listed by Description
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings,. Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns,. Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws,. Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders,. Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
Circlips - External - Grooveless
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Retaining rings. Snap Rings (USA).
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.
Related Information:
Circlips - External - Inverted
N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel. Retaining rings. Snap Rings (USA).
Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips.
Related Information:
Circlips - External - Round Section
DIN7993A / RW / BN825. Retaining rings. Snap Rings (USA).
Round section wire rings are mostly used in semicircular grooves. Applications include gear systems, automotive engineering and open gudgeon pins.
Related Information:
Circlips - External - Standard - Berryllium Copper
Imperial and metric DIN471 / N1400 / D1460. Retaining rings. Snap Rings (USA).
Related Information:
Circlips - External - Standard - Carbon Steel
Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).
Plain carbon steel.
Related Information:
Circlips - External - Standard - Stainless Steel
Imperial and metric DIN471 / D1400 / N1400 / D1460. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel.
Related Information:
Circlips - External - Standard - Zinc Plated
Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).
Zinc plated carbon steel.
Related Information:
Circlips - External - Tabbed
DIN 983 / D2100 / AK. Retaining rings. Snap Rings (USA).
External tabs are concentrically positioned for positioning in a concealed assembly. Tabs act as spacers for securing machine components. Conforming to DIN 983.
Related Information:
Circlips - Internal - Bevelled
N1302 / VHO / 16631 / 9002 / N5002. Retaining rings. Snap Rings (USA).
A 15 Deg. bevel on the outside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments.
Related Information:
Circlips - Internal - Inverted
M1308 / JV / INTV / BN830. Retaining rings. Snap Rings (USA).
Inverted lugs seat into the groove for better clearance and cleaner appearance. Good for shielded bearings that pass tightly through the bore or housing. Use recommended installation pliers.
Related Information:
Circlips - Internal - Round Section
Includes DIN7993B / RB / M1700 / BN826. Retaining rings. Snap Rings (USA).
Round section wire rings are mostly used in semicircular grooves. Applications include gear systems, automotive engineering and open gudgeon pins.
Related Information:
Circlips - Internal - Standard - Carbon Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Plain carbon steel. Tolerances on request. Standard and heavy duty options.
Related Information:
Circlips - Internal - Standard - Stainless Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. Tolerances on request. Standard and heavy duty options.
Related Information:
Circlips - Internal - Standard - Zinc Plated
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Zinc plated carbon steel. Tolerances on request. Standard and heavy duty options.
Related Information:
Circlips - Internal - Tabbed
DIN984 / D2000 / Seeger JK. Retaining rings. Snap Rings (USA).
Internal tabs are concentrically positioned for a concealed assembly. Tabs act as spacers for securing machine components.
Related Information:
Tools - Circlip Pliers - External
Also see combined categories:
All Tools
All Tools
External circlip pliers including standard and ratchet type.
Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected.
Tools - Circlip Pliers - Internal
Also see combined categories:
All Tools
All Tools
Internal circlip pliers including standard and ratchet type.
Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected.
Tools - Circlip Pliers - Reversible
Also see combined categories:
All Tools
All Tools
Reversible circlip pliers for internal and external circlips.
Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected.
Tools - E-Clip Applicators
Also see combined categories:
All Tools
All Tools
Assists with assembly e-clip application. Each tool is designed to suit one or two sizes only.
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127000 products in 2359 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
