Small Parts & Bearings - an MBA company

CIRCLIPS CATEGORIES


Circlips - External - Bevelled
Circlips - External - Bevelled

Also see combined categories:
All External Circlips

N1402 / VSH / 5102 / 16630. Retaining rings. Snap Rings (USA).

A 15 Deg. bevel on the inside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments.

Related Information:


Circlips - External - Grooveless
Circlips - External - Grooveless

Also see combined categories:
All External Circlips

Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Retaining rings. Snap Rings (USA).

Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.

Related Information:


Circlips - External - Inverted
Circlips - External - Inverted

Also see combined categories:
All External Circlips

N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel. Retaining rings. Snap Rings (USA).

Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips.

Related Information:


Circlips - External - Standard - Berryllium Copper
Circlips - External - Standard - Berryllium Copper

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / N1400 / D1460. Retaining rings. Snap Rings (USA).


Related Information:


Circlips - External - Standard - Carbon Steel
Circlips - External - Standard - Carbon Steel

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).

Plain carbon steel.

Related Information:


Circlips - External - Standard - Stainless Steel
Circlips - External - Standard - Stainless Steel

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / D1400 / N1400 / D1460. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).

PH15-7 Mo Stainless Steel.

Related Information:


Circlips - External - Standard - Zinc Plated
Circlips - External - Standard - Zinc Plated

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).

Zinc plated carbon steel.

Related Information:


Circlips - External - Tabbed
Circlips - External - Tabbed

Also see combined categories:
All External Circlips

DIN 983 / D2100 / AK. Retaining rings. Snap Rings (USA).

External tabs are concentrically positioned for positioning in a concealed assembly. Tabs act as spacers for securing machine components. Conforming to DIN 983.

Related Information:


Circlips - Internal - Bevelled
Circlips - Internal - Bevelled

Also see combined categories:
All Internal Circlips

N1302 / VHO / 16631 / 9002 / N5002. Retaining rings. Snap Rings (USA).

A 15 Deg. bevel on the outside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments.

Related Information:


Circlips - Internal - Inverted
Circlips - Internal - Inverted

Also see combined categories:
All Internal Circlips

M1308 / JV / INTV / BN830. Retaining rings. Snap Rings (USA).

Inverted lugs seat into the groove for better clearance and cleaner appearance. Good for shielded bearings that pass tightly through the bore or housing. Use recommended installation pliers.

Related Information:


Circlips - Internal - Standard - Carbon Steel
Circlips - Internal - Standard - Carbon Steel

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Plain carbon steel. Tolerances on request.

Related Information:


Circlips - Internal - Standard - Stainless Steel
Circlips - Internal - Standard - Stainless Steel

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).

PH15-7 Mo Stainless Steel. Tolerances on request.

Related Information:


Circlips - Internal - Standard - Zinc Plated
Circlips - Internal - Standard - Zinc Plated

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Zinc plated carbon steel. Tolerances on request.

Related Information:


Circlips - Internal - Tabbed
Circlips - Internal - Tabbed

Also see combined categories:
All Internal Circlips

DIN984 / D2000 / Seeger JK. Retaining rings. Snap Rings (USA).

Internal tabs are concentrically positioned for a concealed assembly. Tabs act as spacers for securing machine components.

Related Information:


E-Clips - Bowed
E-Clips - Bowed

Also see combined categories:
All E-Clips

For end play take up.

Thickness tolerance +/- 0.025.


E-Clips - Klipring
E-Clips - Klipring

Also see combined categories:
All E-Clips

Also known as Poodle Rings - Imperial - N1504 / NKP



E-Clips - Basic - Berrylium Copper
E-Clips - Basic - Berrylium Copper

Also see combined categories:
All E-Clips

Basic imperial and metric e-clips DIN6799 and N1500. Berrylium Copper.

Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip.

Related Information:


E-Clips - Basic - Carbon Steel
E-Clips - Basic - Carbon Steel

Also see combined categories:
All E-Clips

Basic imperial and metric e-clips DIN6799 and N1500. Carbon spring steel including zinc plated and plain.

Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip. Includes plain and zinc plated.

Related Information:


E-Clips - Basic - Stainless Steel
E-Clips - Basic - Stainless Steel

Also see combined categories:
All E-Clips

Basic imperial and metric e-clips DIN6799 and N1500. Stainless Steel PH15-7 Mo.

Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip.

Related Information:


Wire Rings - External - Round Section
Wire Rings - External - Round Section

Also see combined categories:
All External Circlips

DIN7993A / RW / BN825. Retaining rings. Snap Rings (USA). Round section circlips.

Round section wire rings are mostly used in semicircular grooves. Applications include gear systems, automotive engineering and open gudgeon pins.

Related Information:


Wire Rings - Internal - Round Section
Wire Rings - Internal - Round Section

Also see combined categories:
All Internal Circlips

Includes DIN7993B / RB / M1700 / BN826. Retaining rings. Snap Rings (USA). Round section circlips.

Round section wire rings are mostly used in semicircular grooves. Applications include gear systems, automotive engineering and open gudgeon pins.

Related Information:


You may also be interested in

Tools Circlip


Tools - Circlip Pliers - External
Tools - Circlip Pliers - External

Also see combined categories:
All Tools

External circlip pliers including standard and ratchet type.

Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected.


Tools - Circlip Pliers - Internal
Tools - Circlip Pliers - Internal

Also see combined categories:
All Tools

Internal circlip pliers including standard and ratchet type.

Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected.


Tools - Circlip Pliers - Reversible
Tools - Circlip Pliers - Reversible

Also see combined categories:
All Tools

Reversible circlip pliers for internal and external circlips.

Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected.


Tools - E-Clip Applicators
Tools - E-Clip Applicators

Also see combined categories:
All Tools

Assists with assembly e-clip application. Each tool is designed to suit one or two sizes only.


Clips


Snap Rings - Internal - Basic
Snap Rings - Internal - Basic

Also see combined categories:
All Internal Snaprings

M2300 / SB / ESB Snaprings. Like an internal circlip without the lugs.

Applications include gear systems, securing needle bearings and to act as spacers. Used on the inside bore diameter of a housing or similar.


Pins Clevis


Pins - Clevis - Zinc Plated - Groove Locking
Pins - Clevis - Zinc Plated - Groove Locking

Also see combined categories:
All Clevis Pins

Match with a suitable E-Clip or Circlip to suit groove size shown in listings

In addition to retaining parts on a shaft or axle, clevis pins can also be used as light duty axles, spring holders or even fishing line weights. Sinc plated low carbon steel. Grooved end to suit retaining clip instead of pin.

Related Information:


Pins - Clevis - Stainless Steel 300 Grade - Groove Locking
Pins - Clevis - Stainless Steel 300 Grade  - Groove Locking

Also see combined categories:
All Clevis Pins

Match with a suitable E-Clip or Circlip to suit groove size shown in listings

In addition to retaining parts on a shaft or axle, clevis pins can also be used as light duty axles, spring holders or even fishing line weights. Grooved end to suit retaining clip instead of pin.

Related Information:


Bearings - Linear - Ball - Miniature - Super High Precision
Bearings - Linear - Ball - Miniature - Super High Precision

Also see combined categories:
All Closed Linear Ball Bearings

High Precision Corrosion Resistant Miniature Linear Bearings.

High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.

Related Information:


Snap Rings - External - Basic
Snap Rings - External - Basic

Also see combined categories:
All External Snaprings

Includes series M3200 / SP / ESP / M2400 / SW snaprings. Similar to a circlip without the lugs.

Carbon sping steel. Used on the outside diameter of a bearing, shaft or similar equipment.





Main Pages

About Us Balls List Bearings List Brands Catalogue Contact Us Charity Dental Bearings Dowel Pins Downloadable PDF Catalogue Ball Lock Pins Downloadable PDF Catalogue Balls Downloadable PDF Catalogue Ceramic Bearings Downloadable PDF Catalogue Circlips Downloadable PDF Catalogue Clevis Pins Downloadable PDF Catalogue Corrosion Resistant Bearings Downloadable PDF Catalogue Disc Springs Downloadable PDF Catalogue Dowel Pins Downloadable PDF Catalogue Economy Bearings Downloadable PDF Catalogue Hammer Drive Pins Downloadable PDF Catalogue High Speed Bearings Downloadable PDF Catalogue Key Steel Downloadable PDF Catalogue Knobs Downloadable PDF Catalogue Leveling Mounts Downloadable PDF Catalogue Metallic Bushes Downloadable PDF Catalogue O-Rings Downloadable PDF Catalogue Pins Downloadable PDF Catalogue Plastic Bearings Downloadable PDF Catalogue Polyvee Belts and Pulleys Downloadable PDF Catalogue Precision Shim Washers Downloadable PDF Catalogue Push On and Push In Rings Downloadable PDF Catalogue Rod & Tube Downloadable PDF Catalogue Roll Pins Downloadable PDF Catalogue Shaft Collars Downloadable PDF Catalogue Shim Sheet Downloadable PDF Catalogue Shoulder Screws Downloadable PDF Catalogue Sintered Bronze Bushes Downloadable PDF Catalogue Snap Rings Downloadable PDF Catalogue Socket Set Screws Downloadable PDF Catalogue Solid Bronze Bushes Downloadable PDF Catalogue Spring Steel Strip Downloadable PDF Catalogue Springs Downloadable PDF Catalogue Standard Ball Bearing Range Downloadable PDF Catalogue Super Precision Bearings Downloadable PDF Catalogue Taper Pins Downloadable PDF Catalogue Thrust Bearings Downloadable PDF Catalogue Thumb Screws and Nuts Downloadable PDF Catalogue Timing Belts Downloadable PDF Catalogue Timing Pulley Stock Downloadable PDF Catalogue Timing Pulleys Downloadable PDF Catalogue Vibration Mounts Downloadable PDF Catalogue Washers Downloadable PDF Catalogue Wave Washers Downloadable PDF Cross Reference ADR and SKF Downloadable PDF Cross Reference Anderton Circlips Downloadable PDF Cross Reference Barden Bearings Downloadable PDF Cross Reference Essentra Downloadable PDF Cross Reference Flocast Downloadable PDF Cross Reference K&S Metals Downloadable PDF Cross Reference McMaster Carr Downloadable PDF Cross Reference Miniature Precison Bearings Downloadable PDF Cross Reference Nordex Downloadable PDF Cross Reference NSK and NTN Downloadable PDF Cross Reference Ondrives Downloadable PDF Cross Reference Reid Supply Downloadable PDF Cross Reference SDP-SI Designatronics Downloadable PDF Cross Reference Seeger Circlips Downloadable PDF Cross Reference Sintered Bronze Downloadable PDF Cross Reference Small Parts Inc Downloadable PDF Cross Reference Timing Belts and Pulleys Freight Rates and Shipping Times Frequently Asked Questions Google Search Hobby Clearance Hobby Information Large Bearings Mailorder Form Order History Ordering Payment and Shipping Privacy Product Showcase Shipping Rates and Times Technical Terms


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 131167 products in 2163 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 131167 products in 2163 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.