CC315 REID
Cross Referenced Part Numbers
Reid part number CC-315Matches our part number
Bore 1 (A): 25.400 . Bore 2 (B): 25.400. OD (D): 44.450.
Part Link: CP-254-254-44-076-R1-SC
Online Price: 0.00
Stock: Pre-Order (due 3 weeks) Due dates are estimates only
Stock: Pre-Order (due 3 weeks) Due dates are estimates only
Category Matches
Bushes Plastic
Bushes - Plastic - Iglidur X - Flanged
Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.
Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur X - Unflanged
Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.
Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Balls - Rubber - Santoprene 87A
A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.
It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .96 g/cc. Hardness, Shore 87A. Tensile Strength 2550 psi. Melting Point 400 F. Rohs Compliant and FDA compliant. This grade is slightly softer than the 40D grade. Colour Beige.
Related Information:
Accutorq Ritter Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Accessories - Hobby - Car and Buggy
Generic Parts. Specific model parts may also be found by typing the model number into the search box. Fail safes, aerials, heat sinks, body clips, tune pipe, clutch bell, bump start, engine break stand, engine fans, antenna tubes and tire warmers.
Includes Kyosho pull starts.
Accessories - Hobby - Wheel Nuts Adaptors and Pins
Replacement Wheel Nuts, adaptors and pins for remote control cars
Batteries - Accessories
Miscellaneous battery accessories - Lipo safety charge sacks - Balancers - Leads - Battery Monitors - Etc
Related Information:
Dubro Accessories Listed by Description
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings,. Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns,. Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws,. Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders,. Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
Balls - Rubber - Santoprene 40D
A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.
It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .95 g/cc. Hardness, Shore 40D. Tensile Strength 3000 psi. Melting Point 410 F. Rohs Compliant. Not FDA compliant. This grade is slightly harder than the 87A grade. Colour usually red but some sizes are beige.
Related Information:
Ballscrew - Thomson Saginaw - Accessories
Wiper Kits and Flanges for Ball Nuts. Match all components within the Thomson Saginaw range only.
Linear Slide - Drylin - Accessories
Insensitive to dust and dirt.
Carriage blocks and half slide rail. Make your own custom sized assemblies. Replace blocks on carriage assemblies. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
Related Information:
Dubro by description Dubro Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Dubro by part number Dubro Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Ballscrew - Thomson Saginaw - Nut
Ball Nuts to Suit Thomson Saginaw ball screws. Match all components within the Thomson Saginaw range only.
All Right hand thread only.
Rings - Crescent
Variation of an E-Clip with an open face. Also known as a C-Clip.
Narrow section height provides good clearance capabilities. Absence of teeth and deep set mean less thrust load ratings than e-clips. For best results install using the recommended applicator tool.
Related Information:
Handles - Latching - Cab Locks
Zinc finished steel. Accepts 5/16 in. square shank. Inside handle, right or left hand. Picture shown is right hand.
Mounts - Universal - For Acme Thread and Ballscrews
Use grade 8 hex socket head cap screws for mounting.
Related Information:
Assemblies - Locking - Flanged
Suitable for locking sprockets, pulleys, eccentric shafts.
Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. Flange eliminates axial movement of secured component. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub.
Magnets - Ceramic Blocks
Low cost, light weight, high energy material
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Magnets - Ceramic Cylinder
Low cost, light weight, high energy material
Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.
Screws - Captive - Retractable - Steel
Compliance with UL 1950 and EN 60950 codes for access areas. Ratchet mechanism allows screw to be tightened down by hand, but a tool is needed to loosen.Fully retractable captive to the panel and spring ejected.
Press in style. Bright chromate zinc plated, case hardened steel with aluminium knob and stainless steel spring. Knobs available either slotted or no.2 phillips.
Linear Slide Assemblies - Ball - Pre-Loaded - Compliant
Pre-loaded ball slides provide an acceptable level of accuracy of 0.001mm per mm for most linear motion applications. Considerably lower cost than crossed roller slides.
Uses a conventional hardened steel rod raceway and balls. Incorporates an elastomer spine and shock absorbing backup gib. Provides even and continuous preload, whilst minimising the effects of impact and shock. Tolerant to contamination and can operate of millions of cycles without lubrication. 8-32 UNC mounting holes.
Bumpers - Round - Urethane - Female Washer
With steel core. Washer type has a counterbored hole to accept a socket head cap screw. Flat washer molded inside.
Linear Slide Assemblies - Ball - Pre-Loaded - Hard Gib
Pre-loaded ball slides provide an acceptable level of accuracy of 0.001mm per mm for most linear motion applications. Considerably lower cost than crossed roller slides.
Hard gib preload. Tolerant to contamination and can operate of millions of cycles without lubrication. 8-32 UNC mounting holes.
Shafts - Idler
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design.
Related Information:
Tools - Installation - Indexing Plunger
Two slots provided in the upper end of the body and are accessible when the knob is in the retracted position. For use with WIP type plungers.
Slides - Linear - Cross Roller Rail
Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.
Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds.
Shafting - Ground - Precision - Chrome Plated
Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.
Case hardened to 60-65 Rockwell C. Chrome plated for corrosion resistance.
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127030 products in 2352 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
