CBL40 REID
Cross Referenced Part Numbers
Reid part number CBL-405Matches our part number
For cable diameter: 0.79. Holding Strength: 49.895. Material: Copper.
Group: Attachments - Stop Sleeves
Part Link: PLG-08
Online Price: 0.00
Stock: Pre-Order (due 3 weeks) Due dates are estimates only
Stock: Pre-Order (due 3 weeks) Due dates are estimates only
Reid part number CBL-40Matches our part number
Cable OD: 2.38. Wire Diameter (A): 2.381. Breaking Strength: 417.3.
Group: Cable - Miniature - Uncoated
Part Link: CBLU-238-304-77
Online Price: 0.00
Stock: Pre-Order (due 3 weeks) Due dates are estimates only
Stock: Pre-Order (due 3 weeks) Due dates are estimates only
Category Matches
Bushes Plastic
Bushes - Plastic - Clip - Bevelled Edge
M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F). Used as a light duty split bearing.
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight.
Related Information:
Suspension Units
Suspension Units - Rubber - Square - Insert Type
Housing: Steel / Rubber: Black, hardness 70 Shore. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: +/-30o. Operating Temperature Range: -40oC to +80oC.
You may also be interested in
Housings with Bearing
Housings - Bearing - Flanged - Square - W300
With integral self aligning plain bearing.
Housing : Igumid G. Ball : Highly wear resistant Iglidur W300. Temperature range -40 oC to +180 oC.
Housings - Bearing - Pillow Block - Thermoplastic - W300
Iglide L280 / Igus W300 Ball with Thermoplatic Body.
Maintenance Free, Lightweight, Self-Lubricating. Compensates for alignment errors. Temperature Range -40 oC to +130 oC. Max. Static Tensile Strength is Long Term. Info for Short Term also available.
Bearings Press In
Bearings - Press-Fit - Acetal - SDP
Press fit installation. Do not press bearing against insert. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 oC. Carbon steel outer. Self aligning to +/- 5o. Use any shaft material with 0.4 um or finer finish.
Related Information:
Bushes Plastic
Bushes - Plastic - Clip - Double Flanged
For use with sheet metal. Used as a light duty split bearing.
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40 oC to 80 oC (minus 40 Deg F to 176 Deg F).
Related Information:
Linear Bearings
Bearings - Linear - Sliding - Ceramic Coated
Approved for direct food contact in applications where animal fat or food approved lubricants are present.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Minimum shaft hardness RC35. Max PV 40,000. Temperature range -125 oC to +226 Deg C. Max static PSI 5000.
Engineering and Hobby Rod
Rod - Round - Nylon
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
Related Information:
Springs Die
Springs - Die - Imperial - Medium Duty
Vapor degassed high tensile strength chromium alloy steel. Spring ends are ground square. Designed for long life cycle with constant high end deflections and shot peened to increase fatigue life.
Colour coded blue. Efficient operating range is 25 to 40 percent of the length. Maximum deflection is 50 percent of the length.
Related Information:
Engineering and Hobby Rod
Rod - Round - Acetal
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
Related Information:
Linear Slides
Slides - Dovetail
Used for work feeders for production milling, positioning fixutres, work holding devices, checking fixtures, shuttle devices, assembly equipment, etc.
Tapered gibs are adjusted with a single screw that moves the gib on the taper. This type remains parallel and wears less as it occurs over the entire surface. Made of continuous cast GS 40,000 PSI pearlitic grey iron. Able to be milled, drilled, tapped, etc.
Couplings K Type
Couplings - K Type
Up to 3600 RPM - Minus 20 to Plus 60o C. 0.34 to 18 Nm.
Strong, flexible polyurethane or Hyrtel(R) is cut and tear resistant. Up to 3600 RPM. Urethane: Minus 20 to Plus 60o C / Hyrtel(R) : Minus 40 to Plus 100o C. Precision swaged mechanically crimped hubs. Annealed steel hubs.
Related Information:
Spring Mounts
Springs - Urethane
Urethane springs are designed for use in applications where corrosion, vibration or magnetism prevent the use of conventional steel springs.
They replace steel coil springs in medium pressure applications involving space limitations, high blank holding pressure and adequate stripping. Durometer 95 shore A. Colour black. Tensile strength 5000 psi. Temperature range minus 40 to 80 oC.
Related Information:
Housings with Bearing
Housings - Bearing - Pedestal - Miniature - Self Aligning
Spyraflo pressed steel housings incorporating Abec 3 bearings in a special seat allowing for +/- 5 Deg Misalignment. Improves performance and reduces manufacturing costs. Simplify designs.
Small and cost effective. All bore sizes are mounted in the same size housing for ease of design and cost efficiency. High precision bearings pre-mounted with a 5o misalignment capability. 40,000 RPM recommended maximum speed with testing. 27kgf radial static capacity, 54kgf radial dynamic capacity per bearing. RoHS, REACH and SVHC environmental compliant.
Belts Timing GT2 5mm
Belts - Timing - 5.000mm Pitch - GT2 - 25mm Wide
GT2 Series Metric Timing Belts.
The TruMotion(R) belt construction utilizes a cream-colored polymer compound reinforced with fiberglass tensile cord and a clean polymer-free nylon tooth facing. The belt can withstand high and low temperature ranges of -40oF to +220oF, has a virtually dust-free operation and is non-marking. The belt also has a high flex life and resistance to elongation. Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.
Related Information:
4000 MS-ML Siemens Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
4000 S-SL Push Button Siemens Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
400 Midwest Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Stradic 4000 FI Shimano Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Theory 4000 Daiwa Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Belts - Timing - 2.000mm Pitch - GT2 - Clean - 6mm Wide
PowerGrip(R) TruMotion(R) Timing Belts in 2.000mm.
The TruMotion(R) belt construction utilizes a cream-colored polymer compound reinforced with fiberglass tensile cord and a clean polymer-free nylon tooth facing. The belt can withstand high and low temperature ranges of -40oF to +220oF, has a virtually dust-free operation and is non-marking. The belt also has a high flex life and resistance to elongation. Pitch (P) - 2.00mm, Tooth Height (H) - 0.76mm, Belt Height (W) - 1.52mm. Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.
Related Information:
Balls - Stainless Steel - 400 Grade
Hardness: Rockwell C: 55-60. Includes 420 and 440C grades
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. AISI440C Stainless Steel.
Related Information:
Balls - Rubber - Santoprene 40D
A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.
It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .95 g/cc. Hardness, Shore 40D. Tensile Strength 3000 psi. Melting Point 410 F. Rohs Compliant. Not FDA compliant. This grade is slightly harder than the 87A grade. Colour usually red but some sizes are beige.
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 3.2mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 4.8mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 6.4mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 7.9mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
Related Information:
Pulleys - Timing - 2.073mm Pitch - 40DP - 4.8mm Wide - Through Bore
Timing Pulleys to suit 40DP 2.070mm Pitch Timing Belts. Suits belts 4.7 to 4.8mm wide. Also known as LT.
Aluminium Alloy. Finished Through Bore Ready To Assemble.
Related Information:
Pulleys - Timing - 2.073mm Pitch - 40DP - 6.4mm Wide - Plastic - Plain
Timing Pulleys to suit 40DP 2.070mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Also known as LT. Moulded single or double flange. No locking device.
Related Information:
Pulleys - Timing - 2.073mm Pitch - 40DP - 7.9mm Wide - Through Bore
Timing Pulleys to suit 40DP 2.070mm Pitch Timing Belts. Suits belts 7.9 to 8.0mm wide. Also known as LT.
Aluminium Alloy. Finished Through Bore Ready To Assemble.
Related Information:
Pulleys - Timing - 2.073mm Pitch - 40DP - STOCK - Aluminium
For manufacture of timing pulleys or applications requiring multiple belts from a single drive. Also known as LT.
Related Information:
Dampers - Rotary - 50 to 400 Ncm
Rotary dampers enable products to function with a smooth mechanical motion. Prevent lid and access panel closure damage.
Body: Polycarbonate. Temp range 0 to 50 oC. Weight: Max 120 grams.
Belts - Timing - 14.000mm Pitch - GT2 - 40mm Wide
GT2 Series Metric Timing Belts
Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 14.000mm Pitch - HTD - 40mm Wide
HTD Series Metric Timing Belts
Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.
Related Information:
Pulleys - Timing - 14.000mm Pitch - GT2 - 40mm Wide - Taperlock
Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 40mm wide. Taperlock
Cast Iron. Match with a taperlock to suit your bore requirements.
Related Information:
Belts - Timing - 2.032mm Pitch - MXL - Clean - 3.2mm Wide
PowerGrip(R) TruMotion(R) Timing Belts in 2.032mm or 0.080 inch pitch.
The TruMotion(R) belt construction utilizes a cream-colored polymer compound reinforced with fiberglass tensile cord and a clean polymer-free nylon tooth facing. The belt can withstand high and low temperature ranges of -40oC to +90oC, has a virtually dust-free operation and is non-marking. The belt also has a high flex life and resistance to elongation. TruMotion(R) belts have a durable wear surface for longer life and are RoHS compliant. Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. RoHs comliant.
Related Information:
S400 - S405 Faro Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Calcutta 50-100-150-200-250-251-400-600 Shimano Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
DA4000M Daiwa Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
340 Polaris Pool Cleaner Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Flanges - Timing Pulley - Suit 2.032mm MXL and 40DP Series
Use with timing pulley stock to custom make your own pulleys
Related Information:
Micromotor MC2 20-40E - 20GTAV-40GTAV - 20GT-40GT Bien Air Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings - Ball - 440C Stainless
Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
Stainless steel radial ball bearings
Standard single row radial ball bearings. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
Micromat-Athlet Type H240B Motor Muss Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127030 products in 2352 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
