Stainless steel ball type cam followers.
Small carbon steel roller type cam followers.
Carbon Steel - Nitrile Rubber seals assembled in the outer ring. Screwdriver slot for mounting. Stud designed to fit H7 housing.
Related Information:
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
Related Information:
Carbon steel roller type cam followers.
Load 1 applies when outer race is mounted into a housing with standard bearing fit. Load 2 applies when used as a track roller. Stud designed to fit H7 housing.
Related Information:
Urethane tyred cam followers for noise reduction, reduced wear and non marking
Related Information:
Urethane tyred cam yoke rollers for noise reduction, reduced wear and non marking
Polycoated shore 80A cast urethane cover.
Related Information:
Used with cam action indexing plungers
Mounting blocks are made from steel with black oxide finish.
Related Information:
Used in many tooling applications as well as on many types of machinery and equipment.
Plunger is retracted as the nadle is turned on the cam of the body. Groove on top of cam locks the plunger into retracted position. Body made from black oxide coated steel. Plunger is made from steel, ground and nitrided.
Related Information:
Used in many tooling applications as well as on many types of machinery and equipment.
Plunger is retracted as the nadle is turned on the cam of the body. Groove on top of cam locks the plunger into retracted position. Body made from black oxide coated steel. Plunger is made from steel, ground and nitrided.
Related Information:
With 5.08mm offset cam. Cam may be reversed for increased grip range. Includes detent in body which signals positive open or closed position.
The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
Designed for press fit installation. Correct interference dimensions must be maintained to obtain maximum bearing and clutch performance. Mount the clutch ensuring that the shaft drive directionis in the direction indicated by the arrow on the inner race. To install, use a press tool / do not hammer or apply other stock to clutch. Make sure housing has enough strength to withstand press required for fitting installation. High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes.
Related Information:
Supplied in pairs.
Locking function not affected by lubrication. Assembled in pairs, cam face to cam face. Eliminates the need for adhesives. Reusable. Can be used with fasteners up to grade 12.9.
Quarter turn latches. Nema 4 and IP65 rated. Supplied assembled. Includes housing, insert, rubber seal, gasket, hex nut and cam.
Heavy Duty. Grip range is approximate and calculated as the door flange with compressed gasket and cabinet flange. Black polyamide handle. The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.
Supplied in pairs. With Delta Protekt coating.
Locking function not affected by lubrication. Assembled in pairs, cam face to cam face. Eliminates the need for adhesives. Reusable. Can be used with fasteners up to grade 12.9.
Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.
Alternative to ball bearings - quiet operation - patented design.
Applications include compact fan motors, copy machines, printers, laptop computers, cameras and toys. Stainless Steel casing and shield - Long Life. Use with Case Hardened shafting 2um surface finish -0.007/-0.012 for normal use. Use with Case Hardened shafting 1um surface finish -0.005/-0.007 for high accuracy use. 30% weight savings over ball bearings.
Related Information:
Self fusing silicone wrapping tape for emergency repairs or general protection. Seals leaks. Permanent. Self Bonding. No adhesive. Supa Tape.
Resists Fuels, Oils, Acid, Solvent, Salt Water, Road Salt and UV Rays. Temp Range minus 50 oC to plus 260 deg C. Insulates 8000 Volts (per unstretched layer). Tensile Strength 700psi. Lasts for years with a permanent air tight and water tight seal. Some uses include emergency radiator hose repair, insulation for radioactive areas, garden hose repair, exhaust pipe repair, electrical insulation, tool grips, sporting grips, rope ends, air duct joints, wire bundles. Areas of use include outdoor, auto, marine, workshop, motorcycle, camper, hunting, fishing, farming, plumbing, corrosive areas.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 126998
products in 2361 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.