Small Parts & Bearings - an MBA company

Bushings Spherical Plastic Categories


Bushings Spherical


Bushings - Spherical - Plastic
Bushings - Spherical - Plastic

Also see combined categories:
All Spherical Bushings

Plastic spherical plain bearings. Also known as ball bushings.

Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.


Bushings - Spherical - Steel
Bushings - Spherical - Steel

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Bushings - Spherical - Steel - With Oil Hole
Bushings - Spherical - Steel - With Oil Hole

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Bushings - Spherical - Steel - With Wiper Seal
Bushings - Spherical - Steel - With Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


You may also be interested in

Bearings for Housings


Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings
Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings


Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.

Load and speed calculations are for reference only. Testing is recommended.

Related Information:


Bearings Thrust


Washers - Self Aligning - Sets - Plastic
Washers - Self Aligning - Sets - Plastic

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers

Tensile strengths shown are Static Axial in Newtons. Easy to install. Good friction wear properties.

Related Information:


Bushes Plastic


Bushings - Snap - Closed
Bushings - Snap - Closed


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.

Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber.

Related Information:


Bushings - Snap - Open
Bushings - Snap - Open


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.

Also called a dome plug. Also see grommets for a similar product made from rubber.

Related Information:


Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur G - Unflanged
Bushes - Plastic - Iglidur G - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H - Flanged
Bushes - Plastic - Iglidur H - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H - Unflanged
Bushes - Plastic - Iglidur H - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur M250 - Flanged
Bushes - Plastic - Iglidur M250 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur M250 - Unflanged
Bushes - Plastic - Iglidur M250 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur P - Flanged
Bushes - Plastic - Iglidur P - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur P - Unflanged
Bushes - Plastic - Iglidur P - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur J - Flanged
Bushes - Plastic - Iglidur J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur J - Unflanged
Bushes - Plastic - Iglidur J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur Q - Flanged
Bushes - Plastic - Iglidur Q - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur Q - Unflanged
Bushes - Plastic - Iglidur Q - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur F - Flanged
Bushes - Plastic - Iglidur F - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur F - Unflanged
Bushes - Plastic - Iglidur F - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur Z - Flanged
Bushes - Plastic - Iglidur Z - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur Z - Unflanged
Bushes - Plastic - Iglidur Z - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H370 - Flanged
Bushes - Plastic - Iglidur H370 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H370 - Unflanged
Bushes - Plastic - Iglidur H370 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A200 - Flanged
Bushes - Plastic - Iglidur A200 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A200 - Unflanged
Bushes - Plastic - Iglidur A200 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A290 - Flanged
Bushes - Plastic - Iglidur A290 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A290 - Unflanged
Bushes - Plastic - Iglidur A290 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur X - Flanged
Bushes - Plastic - Iglidur X - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur X - Unflanged
Bushes - Plastic - Iglidur X - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Seals and Sealing


Grommets - Rubber - EPDM
Grommets - Rubber - EPDM

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

EPDM Rubber Grommets

50 +/-5 Durometer. Easy to install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Grommets - Rubber - Natural
Grommets - Rubber - Natural

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

Natural Rubber Grommets

50 +/-5 Durometer. Easy to Install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Grommets - Rubber - EPDM - Closed
Grommets - Rubber - EPDM - Closed

Also see combined categories:
All Closed Rubber Grommets
All Rubber Grommets

Closed EPDM Rubber Grommets

50 +/-5 Durometer. Dustproof with Approx 0.5mm thick Membrane. Easy to Install. Dust protection. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Handles - Latching - 2-Point Locking Rod Kit
Handles - Latching - 2-Point Locking Rod Kit


Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.



Bushes - Bronze - Spherical - Sintered
Bushes - Bronze - Spherical - Sintered

Also see combined categories:
All Bronze Bushes

Spherical OD Oil Impregnated Sintered Bronze Bushes.

ID and OD oversized. Enquire if details required.

Related Information:


Bearings - Spherical OD
Bearings - Spherical OD


Bearings with a spherical outside diameter.

Combined listing of spherical OD track rollers and bearings for Linear Guide systems.

Related Information:


Washers - Self Aligning - Components - Hardened Steel
Washers - Self Aligning - Components - Hardened Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.

Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.


Washers - Self Aligning - Components - Stainless Steel
Washers - Self Aligning - Components - Stainless Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.

AISI 303 Stainless Steel. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.


Washers - Self Aligning - Sets - Hardened Steel
Washers - Self Aligning - Sets - Hardened Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers

Hardened steel 9 S Mn Pb 28 K DIN 6319. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.


Washers - Self Aligning - Sets - Stainless Steel
Washers - Self Aligning - Sets - Stainless Steel

Also see combined categories:
All Thrust Washers
All Aligning Washers

Spherical Seat Washers

AISI 303 Stainless Steel. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.


Bearings - For Cast Iron Housings
Bearings - For Cast Iron Housings


Insert bearings with spherical OD for use with cast iron flanged and pillow block housings.

Grub Screw locking. Preferred misallignment of no more than 2o, but can accommodate up to 6o. Also available with eccentric locking collars on request. Lubrication Hole to match Lubrication groove in housing.

Related Information:


Bearings - For Pressed Metal Housings
Bearings - For Pressed Metal Housings


Insert bearings with spherical OD for use with pressed metal flanged and pillow block housings.

Grub Screw locking. Preferred misallignment of no more than 2o, but can accommodate up to 6o. Also available with eccentric locking collars on request.

Related Information:


Bushes - Plastic - X-Lube - Flanged
Bushes - Plastic - X-Lube - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Self lubricating - low friction - non-corrosive - light weight - chemical resistant.

Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.

Related Information:


Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing
Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing


Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.


Bushes - Plastic - Clip - Bevelled Edge
Bushes - Plastic - Clip - Bevelled Edge

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F). Used as a light duty split bearing.

Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124472 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124472 products in 2754 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.