Bushings Spherical Categories
Bushings - Spherical - Plastic
Plastic spherical plain bearings. Also known as ball bushings.
Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.
Bushings - Spherical - Steel
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment.
Bushings - Spherical - Steel - With Oil Hole
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment.
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment.
Bushings - Spherical - Steel - With Wiper Seal
Steel spherical plain bearings. Also known as ball bushings.
Compensates for axial loads and misalignment.
Bushes - Bronze - Spherical - Sintered
Spherical OD Oil Impregnated Sintered Bronze Bushes.
ID and OD oversized. Enquire if details required.
Related Information:
Bearings - Spherical OD
Bearings with a spherical outside diameter.
Combined listing of spherical OD track rollers and bearings for Linear Guide systems.
Related Information:
Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Washers - Self Aligning - Sets - Plastic
Spherical Seat Washers
Tensile strengths shown are Static Axial in Newtons. Easy to install. Good friction wear properties.
Related Information:
Washers - Self Aligning - Components - Hardened Steel
Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.
Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Washers - Self Aligning - Components - Stainless Steel
Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.
AISI 303 Stainless Steel. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Washers - Self Aligning - Sets - Hardened Steel
Spherical Seat Washers
Hardened steel 9 S Mn Pb 28 K DIN 6319. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Washers - Self Aligning - Sets - Stainless Steel
Spherical Seat Washers
AISI 303 Stainless Steel. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
Bearings - For Cast Iron Housings
Insert bearings with spherical OD for use with cast iron flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2o, but can accommodate up to 6o. Also available with eccentric locking collars on request. Lubrication Hole to match Lubrication groove in housing.
Related Information:
Bearings - For Pressed Metal Housings
Insert bearings with spherical OD for use with pressed metal flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2o, but can accommodate up to 6o. Also available with eccentric locking collars on request.
Related Information:
Bushings - Snap - Closed
Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.
Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber.
Related Information:
Bushings - Snap - Open
Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.
Also called a dome plug. Also see grommets for a similar product made from rubber.
Related Information:
Pins - Dowel Bushings
Series DB100 Spirol
Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12.
Related Information:
Bushings - QD
Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing
Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley.
Related Information:
Bushings - Drill - Liner Type - Headless
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.
Bushings - Drill - Press-fit - Headless
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Bushings - Drill - Press-fit - Headless - Tungsten Carbide
Designed to guide, position, and support the cutting tool in a metalworking jig.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.
Bushings - Drill - Press-fit - Standard Head
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Bushings - Drill - Slip - With Head
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.
Bushings - Tension
Like a heavy duty roll pin.
Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications.
Bushings - Stroke Rotary - Miniature
2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.
Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.
Related Information:
Dual Vee - Adaptor Bushings
Vee grooved track roller bushings.
Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned.
Related Information:
Elements - Locking
2.4 to 2200 Nm, 6-80mm Bores
ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8.
Bushes - Plastic - Iglidur G - Flanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur G - Unflanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur H - Flanged
Underwater performance. High Temp. Chemical Resistance.
Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur H - Unflanged
Underwater performance. High Temp. Chemical Resistance.
Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Pulleys - Vee - A - 4L - Single Row - For QD Bushing
Cast iron pulleys. QD bushings are used to vary the bore sizes.
Related Information:
Pulleys - Vee - B - 5L - Single Row - For QD Bushing
Cast iron pulleys. QD bushings are used to vary the bore sizes.
Related Information:
Bushes - Plastic - Iglidur M250 - Flanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur M250 - Unflanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur P - Flanged
Low water absorption. Low wear. Hgh load.
Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur P - Unflanged
Low water absorption. Low wear. Hgh load.
Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur J - Flanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur J - Unflanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur Q - Flanged
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur Q - Unflanged
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Ball Buttons
Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.
Burnished ground hardened steel.
Bushes - Plastic - Iglidur F - Flanged
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Bushes - Plastic - Iglidur F - Unflanged
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127031 products in 2352 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
