Small Parts & Bearings - an MBA company

Bushings Snap Closed Categories


Bushes Plastic


Bushings - Snap - Closed
Bushings - Snap - Closed


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.

Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber.

Related Information:


Bushings - Snap - Open
Bushings - Snap - Open


Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.

Also called a dome plug. Also see grommets for a similar product made from rubber.

Related Information:


You may also be interested in

Seals and Sealing


Grommets - Rubber - EPDM - Closed
Grommets - Rubber - EPDM - Closed

Also see combined categories:
All Closed Rubber Grommets
All Rubber Grommets

Closed EPDM Rubber Grommets

50 +/-5 Durometer. Dustproof with Approx 0.5mm thick Membrane. Easy to Install. Dust protection. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Grommets - Rubber - EPDM
Grommets - Rubber - EPDM

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

EPDM Rubber Grommets

50 +/-5 Durometer. Easy to install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Grommets - Rubber - Natural
Grommets - Rubber - Natural

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

Natural Rubber Grommets

50 +/-5 Durometer. Easy to Install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:


Pins Dowel


Pins - Dowel Bushings
Pins - Dowel Bushings

Also see combined categories:
All Dowel Bushings

Series DB100 Spirol

Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12.

Related Information:


Bushings - QD and Taperlock


Bushings - QD
Bushings - QD


Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing

Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley.


Tension Bushings


Bushings - Tension
Bushings - Tension


Like a heavy duty roll pin.

Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications.


Bushings - QD and Taperlock


Bushings - Taperlock
Bushings - Taperlock




Bushings Spherical


Bushings - Spherical - Plastic
Bushings - Spherical - Plastic

Also see combined categories:
All Spherical Bushings

Plastic spherical plain bearings. Also known as ball bushings.

Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.


Bushings - Spherical - Steel
Bushings - Spherical - Steel

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Bushings - Spherical - Steel - With Oil Hole
Bushings - Spherical - Steel - With Oil Hole

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Bushings - Spherical - Steel - With Wiper Seal
Bushings - Spherical - Steel - With Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Clamping Bushings


Bushings - Shoulder
Bushings - Shoulder


Mould components



Locking Bushings


Bushings - Integral Taper
Bushings - Integral Taper

Also see combined categories:
All Locking Assemblies
All Locking Bushings

Stainless Steel Taper Bushings.

Will not mar shafts.


Fastening Bushings


Bushings - Drill - Liner Type - Headless
Bushings - Drill - Liner Type - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Bushings - Drill - Press-fit - Headless
Bushings - Drill - Press-fit - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.



Bushings - Drill - Press-fit - Headless - Tungsten Carbide
Bushings - Drill - Press-fit - Headless - Tungsten Carbide

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Bushings - Drill - Press-fit - Standard Head
Bushings - Drill - Press-fit - Standard Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.



Bushings - Drill - Slip - With Head
Bushings - Drill - Slip - With Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Stroke Rotary Bushings


Bushings - Stroke Rotary - Miniature
Bushings - Stroke Rotary - Miniature

Also see combined categories:
All Stroke Rotary Bushings

2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.

Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.

Related Information:


Dual Vee Bearings


Dual Vee - Adaptor Bushings
Dual Vee - Adaptor Bushings

Also see combined categories:
All Dual Vee Guide Wheels

Vee grooved track roller bushings.

Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned.

Related Information:


Spacers


Spacers - Machinery Bushings
Spacers - Machinery Bushings

Also see combined categories:
All Round Spacers
All Flat Washers and Spacers - Metallic

Used as spacers between pulleys, gears etc

Low carbon mild steel.


Cam Followers


Cam Followers - Self Lubricating - Bronze Bushing
Cam Followers - Self Lubricating - Bronze Bushing

Also see combined categories:
All Cam Followers



Locking Bushings


Elements - Locking
Elements - Locking

Also see combined categories:
All Locking Assemblies

2.4 to 2200 Nm, 6-80mm Bores

ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8.


Bushes Plastic


Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur G - Unflanged
Bushes - Plastic - Iglidur G - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H - Flanged
Bushes - Plastic - Iglidur H - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H - Unflanged
Bushes - Plastic - Iglidur H - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Pulleys Vee


Pulleys - Vee - A - 4L - Single Row - For QD Bushing
Pulleys - Vee - A - 4L - Single Row - For QD Bushing

Also see combined categories:
All Vee Pulleys A Section 12.5 and 12.7mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.


Related Information:


Pulleys - Vee - B - 5L - Single Row - For QD Bushing
Pulleys - Vee - B - 5L - Single Row - For QD Bushing

Also see combined categories:
All Vee Pulleys B Section 15.9 and 16.5mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.


Related Information:


Bushes Plastic


Bushes - Plastic - Iglidur M250 - Flanged
Bushes - Plastic - Iglidur M250 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur M250 - Unflanged
Bushes - Plastic - Iglidur M250 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur P - Flanged
Bushes - Plastic - Iglidur P - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur P - Unflanged
Bushes - Plastic - Iglidur P - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur J - Flanged
Bushes - Plastic - Iglidur J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur J - Unflanged
Bushes - Plastic - Iglidur J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur Q - Flanged
Bushes - Plastic - Iglidur Q - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur Q - Unflanged
Bushes - Plastic - Iglidur Q - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Plungers Ball


Ball Buttons
Ball Buttons


Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.

Burnished ground hardened steel.


Bushes Plastic


Bushes - Plastic - Iglidur F - Flanged
Bushes - Plastic - Iglidur F - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur F - Unflanged
Bushes - Plastic - Iglidur F - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur Z - Flanged
Bushes - Plastic - Iglidur Z - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur Z - Unflanged
Bushes - Plastic - Iglidur Z - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H370 - Flanged
Bushes - Plastic - Iglidur H370 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur H370 - Unflanged
Bushes - Plastic - Iglidur H370 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Bushes - Plastic - Iglidur A200 - Flanged
Bushes - Plastic - Iglidur A200 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124371 products in 2774 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124371 products in 2774 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.