Small Parts & Bearings - an MBA company

Bushings Qd Categories


Bushings - QD and Taperlock


Bushings - QD
Bushings - QD

Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing

Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley.





Pulleys Vee


Pulleys - Vee - A - 4L - Single Row - For QD Bushing
Pulleys - Vee - A - 4L - Single Row - For QD Bushing

Also see combined categories:
All Vee Pulleys A Section 12.5 and 12.7mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.

Related Information:
A /4L Section Vee Belts
Type H QD Bushings


Pulleys - Vee - B - 5L - Single Row - For QD Bushing
Pulleys - Vee - B - 5L - Single Row - For QD Bushing

Also see combined categories:
All Vee Pulleys B Section 15.9 and 16.5mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.

Related Information:
B / 5L Section Vee Belts
Type H QD Bushings


You may also like

Bushes Plastic


Bushings - Snap - Closed
Bushings - Snap - Closed

Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.

Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber.

Related Information:
Also see Grommets


Bushings - Snap - Open
Bushings - Snap - Open

Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.

Also called a dome plug. Also see grommets for a similar product made from rubber.

Related Information:
Also see Grommets


Pins Dowel


Pins - Dowel Bushings
Pins - Dowel Bushings

Also see combined categories:
All Dowel Bushings

Series DB100 Spirol

Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12.



Bushings Spherical


Bushings - Spherical - Plastic
Bushings - Spherical - Plastic

Also see combined categories:
All Spherical Bushings

Plastic spherical plain bearings. Also known as ball bushings.

Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.



Bushings - Spherical - Steel
Bushings - Spherical - Steel

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.



Bushings - Spherical - Steel - With Oil Hole
Bushings - Spherical - Steel - With Oil Hole

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.



Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.



Bushings - Spherical - Steel - With Wiper Seal
Bushings - Spherical - Steel - With Wiper Seal

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.



Clamping Bushings


Bushings - Shoulder
Bushings - Shoulder

Mould components



Locking Bushings


Bushings - Integral Taper
Bushings - Integral Taper

Also see combined categories:
All Locking Assemblies
All Locking Bushings

Stainless Steel Taper Bushings.

Will not mar shafts.



Fastening Bushings


Bushings - Drill - Liner Type - Headless
Bushings - Drill - Liner Type - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.



Bushings - Drill - Press-fit - Headless
Bushings - Drill - Press-fit - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.



Bushings - Drill - Press-fit - Headless - Tungsten Carbide
Bushings - Drill - Press-fit - Headless - Tungsten Carbide

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.



Bushings - Drill - Press-fit - Standard Head
Bushings - Drill - Press-fit - Standard Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.



Bushings - Drill - Slip - With Head
Bushings - Drill - Slip - With Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.



Tension Bushings


Bushings - Tension
Bushings - Tension

Like a heavy duty roll pin.

Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications.



Stroke Rotary Bushings


Bushings - Stroke Rotary - Miniature
Bushings - Stroke Rotary - Miniature

Also see combined categories:
All Stroke Rotary Bushings

2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.

Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.

Related Information:
Stroke Rotary Bushings Technical Info


Dual Vee Bearings


Dual Vee - Adaptor Bushings
Dual Vee - Adaptor Bushings

Also see combined categories:
All Dual Vee Guide Wheels

Vee grooved track roller bushings.

Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned.

Related Information:
General Information
Engineering Notes
Guide Wheels to Suit


Spacers


Spacers - Machinery Bushings
Spacers - Machinery Bushings

Also see combined categories:
All Round Spacers
All Flat Washers and Spacers - Metallic

Used as spacers between pulleys, gears etc

Low carbon mild steel.



Cam Followers




Locking Bushings


Elements - Locking
Elements - Locking

Also see combined categories:
All Locking Assemblies

2.4 to 2200 Nm, 6-80mm Bores

ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8.



Bushes Plastic


Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:
G300 Properties


Bushes - Plastic - Iglidur G - Unflanged
Bushes - Plastic - Iglidur G - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:
G300 Properties


Bushes - Plastic - Iglidur H - Flanged
Bushes - Plastic - Iglidur H - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur H - Unflanged
Bushes - Plastic - Iglidur H - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur M250 - Flanged
Bushes - Plastic - Iglidur M250 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:
M250 Properties


Bushes - Plastic - Iglidur M250 - Unflanged
Bushes - Plastic - Iglidur M250 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:
M250 Properties


Bushes - Plastic - Iglidur P - Flanged
Bushes - Plastic - Iglidur P - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur P - Unflanged
Bushes - Plastic - Iglidur P - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur J - Flanged
Bushes - Plastic - Iglidur J - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur J - Unflanged
Bushes - Plastic - Iglidur J - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur Q - Flanged
Bushes - Plastic - Iglidur Q - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur Q - Unflanged
Bushes - Plastic - Iglidur Q - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Plungers Ball


Ball Buttons
Ball Buttons

Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.

Burnished ground hardened steel.



Bushes Plastic


Bushes - Plastic - Iglidur F - Flanged
Bushes - Plastic - Iglidur F - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur F - Unflanged
Bushes - Plastic - Iglidur F - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur Z - Flanged
Bushes - Plastic - Iglidur Z - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur Z - Unflanged
Bushes - Plastic - Iglidur Z - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur H370 - Flanged
Bushes - Plastic - Iglidur H370 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur H370 - Unflanged
Bushes - Plastic - Iglidur H370 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur A200 - Flanged
Bushes - Plastic - Iglidur A200 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur A200 - Unflanged
Bushes - Plastic - Iglidur A200 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur A290 - Flanged
Bushes - Plastic - Iglidur A290 - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur A290 - Unflanged
Bushes - Plastic - Iglidur A290 - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur X - Flanged
Bushes - Plastic - Iglidur X - Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Bushes - Plastic - Iglidur X - Unflanged
Bushes - Plastic - Iglidur X - Unflanged

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.



Seals and Sealing


Grommets - Rubber - EPDM
Grommets - Rubber - EPDM

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

EPDM Rubber Grommets

50 +/-5 Durometer. Easy to install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:
Also see snap bushings


Grommets - Rubber - Natural
Grommets - Rubber - Natural

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

Natural Rubber Grommets

50 +/-5 Durometer. Easy to Install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:
Also see snap bushings


Grommets - Rubber - EPDM - Closed
Grommets - Rubber - EPDM - Closed

Also see combined categories:
All Closed Rubber Grommets
All Rubber Grommets

Closed EPDM Rubber Grommets

50 +/-5 Durometer. Dustproof with Approx 0.5mm thick Membrane. Easy to Install. Dust protection. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:
Also see snap bushings


Tooling Balls


Balls - Tooling - Two Piece - Construction - Steel
Balls - Tooling - Two Piece - Construction - Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.



Housings with Bearing


Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing
Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing

Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.



Housings - Bearing - 3 Bolt Offset - Thermoplastic with Stainless Bearing
Housings - Bearing - 3 Bolt Offset - Thermoplastic with Stainless Bearing

Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.



Housings - Bearing - 4 Bolt Flange - Thermoplastic with Stainless Bearing
Housings - Bearing - 4 Bolt Flange - Thermoplastic with Stainless Bearing

Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.



Linear Bearings


Bearings - Linear - Sliding - Stainless - PTFE - Closed
Bearings - Linear - Sliding - Stainless - PTFE - Closed

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.



Bearings - Linear - Sliding - Stainless - PTFE - Open
Bearings - Linear - Sliding - Stainless - PTFE - Open

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.



Latches Handle


Handles - Latching - 2-Point Locking Rod Kit
Handles - Latching - 2-Point Locking Rod Kit

Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.



Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Small Parts & Bearings offers 126286 products in 2931 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Small Parts & Bearings offers 126286 products in 2931 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.