BEM16LH ONDRIVES
Cross Referenced Part Numbers
Ondrives part number BEM-16-LHMatches our part number
Eye Size (d1): 16.000. Overall Length (L): 85.00. Thread Size: M16x2 Left.
Part Link: REM-160-L-CB
Retail Price: 0.00
Lower price for quantities
Stock: Pre-Order (due 2 weeks) Due dates are estimates only
Lower price for quantities
Stock: Pre-Order (due 2 weeks) Due dates are estimates only
Category Matches
Gearbox Parts
P30-60 Ondrives Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Gears - Mitre - 16 Diametrical Pitch - Steel
1:1 Ratio. 20o Pressure Angle - Unhardened Steel
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios.
Handles - Latching - Cab Locks
Zinc finished steel. Accepts 5/16 in. square shank. Inside handle, right or left hand. Picture shown is right hand.
Gears - Spur - 16DP - 14.5 Degree - Steel
PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth.
Gears - Spur - 16DP - 20 Degree - Plastic
PCD = No. of Teeth x 1.588mm (1/16 in.). 20o Pressure Angle. Nylon and acetal. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth.
Gear Racks - 16DP - Steel
14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.
16 DP. Approx 4.99mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths.
Belts - Timing - 2.032mm Pitch - MXL - 4.8mm Wide
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 4.76mm (3/16 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Belts - Timing - 2.032mm Pitch - MXL - 7.9mm Wide
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 7.93mm (5/16 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Slides - Drawer - Front Disconnect - Friction - 19mm Ext
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Positive locking mechanism keeps drawer locked in the open position until actively released. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.
Slides - Drawer - Front Disconnect - Lever - Full Ext
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by lifting a lever lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Slides - Drawer - Front Disconnect - Latch Lever - Full Ext
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Ballscrew - 16mm Nuts - Pillow Block
Includes ball nut. Match all components within the 16mm range only.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
Belts - Vee - 16.5 x 11.0mm - B
16.5mm Top Width x 11.0mm Height.
Sizes are nominal and may vary slightly.
Related Information:
Belts - Wedge - 16.3 x 13.0mm - SPB - 5V
16.3mm Top Width x 13.0mm Height.
Sizes are nominal and may vary slightly.
Related Information:
Belts - Timing - 10.000mm Pitch - AT10 - 16mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.
Related Information:
Belts - Timing - 5.000mm Pitch - AT5 - 16mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Timing - 10.000mm Pitch - T10 - 16mm Wide
T Series Metric Timing Belts.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.
Related Information:
Belts - Timing - 5.000mm Pitch - T5 - 16mm Wide
T Series Metric Timing Belts.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 2.65mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.20mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.000mm.
Related Information:
Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore
Timing pulleys to suit AT10 Series belts
Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.
Related Information:
Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore
Timing pulleys to suit AT5 Series belts
Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.
Related Information:
Pulleys - Timing - 10.000mm Pitch - T10 - 16mm Wide - Through Bore
Timing pulleys to suit T10 Series belts
Related Information:
Pulleys - Timing - 5.000mm Pitch - T5 - 16mm Wide - Through Bore
Timing Pulleys to suit T Series 5.000mm Pitch Timing Belts. Suits belts 15.0 to 16.0mm wide.
Aluminium alloy. No locking provided. You will need to drill and tap the hub to suit your desired grub screw. Tapped hubs can be provided on request.
Related Information:
Circlips - External - Inverted
N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel. Retaining rings. Snap Rings (USA).
Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips.
Related Information:
Circlips - Internal - Bevelled
N1302 / VHO / 16631 / 9002 / N5002. Retaining rings. Snap Rings (USA).
A 15 Deg. bevel on the outside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments.
Related Information:
46-243167P1AD Bracket GE Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
46-243167P1AD GE Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Circlips - External - Bevelled
N1402 / VSH / 5102 / 16630. Retaining rings. Snap Rings (USA).
A 15 Deg. bevel on the inside diameter to be fitted to a 15% bevel on the load bearing groove wall. Will yield rigid end-play take-up of manufacturing tolerances or wear on the retained part. Used in greasy or oily environments.
Related Information:
Bearings - 316 Stainless Steel - Spherical OD - For Plastic Housings
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Load and speed calculations are for reference only. Testing is recommended.
Related Information:
Couplings - Helical - Standard
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm.
Related Information:
Tools - Die Holders
Bar and round holders. 16mm, 20.64mm and 25.4mm (inch). Also called a button die stock.
Bearings - Ball - 316 Stainless Steel - Double Row - Open
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance.
Related Information:
Bearings - Ball - 316 Stainless Steel - Single Row - Open
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance.
Related Information:
Bearings - Ball - 316 Stainless Steel - Single Row - Sealed
Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Bearings - Ball - 316 Stainless Steel - Single Row - Shielded
Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Screws - Countersunk - 316 Stainless - Philips
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
Related Information:
Screws - Countersunk - 316 Stainless - Slotted
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
Related Information:
Washers - LockRite - 316 Stainless Steel
Supplied in pairs.
Locking function not affected by lubrication. Assembled in pairs, cam face to cam face. Eliminates the need for adhesives. Reusable. Can be used with fasteners up to grade 12.9.
Balls - Stainless Steel - 316 Grade
A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 oC.
Related Information:
Balls - Stainless Steel - 316L Grade
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
Related Information:
Pins - Dowel - Standard - 316 Stainless - Chamfered End
Precision Dowel Pins - 316 Grade - Based on DIN6325, ISO2338, ISO 8734
Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Precision Dowel Pins - 316 Grade - Based on DIN7
Diameter tolerances are m6. Also known as parallel pins.
Related Information:
Pins - Dowel - Standard - 416 Stainless - Chamfered End
Precision Dowel Pins - 416 Grade - Based on DIN6325 or ISO2338
Also known as parallel pins. Also known as parallel pins.
Related Information:
Screws - Button - Socket - 316 Stainless
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Contact Us
Charity
Dental Bearings
Dowel Pins
Downloadable PDF Catalogue Ball Lock Pins
Downloadable PDF Catalogue Balls
Downloadable PDF Catalogue Ceramic Bearings
Downloadable PDF Catalogue Circlips
Downloadable PDF Catalogue Corrosion Resistant Bearings
Downloadable PDF Catalogue Disc Springs
Downloadable PDF Catalogue Dowel Pins
Downloadable PDF Catalogue Economy Bearings
Downloadable PDF Catalogue Hammer Drive Pins
Downloadable PDF Catalogue High Speed Bearings
Downloadable PDF Catalogue Key Steel
Downloadable PDF Catalogue Knobs
Downloadable PDF Catalogue Leveling Mounts
Downloadable PDF Catalogue Metallic Bushes
Downloadable PDF Catalogue O-Rings
Downloadable PDF Catalogue Pins
Downloadable PDF Catalogue Plastic Bearings
Downloadable PDF Catalogue Polyvee Belts and Pulleys
Downloadable PDF Catalogue Precision Shim Washers
Downloadable PDF Catalogue Push On and Push In Rings
Downloadable PDF Catalogue Rod & Tube
Downloadable PDF Catalogue Roll Pins
Downloadable PDF Catalogue Shaft Collars
Downloadable PDF Catalogue Shim Sheet
Downloadable PDF Catalogue Shoulder Screws
Downloadable PDF Catalogue Sintered Bronze Bushes
Downloadable PDF Catalogue Socket Set Screws
Downloadable PDF Catalogue Solid Bronze Bushes
Downloadable PDF Catalogue Spring Steel Strip
Downloadable PDF Catalogue Springs
Downloadable PDF Catalogue Standard Ball Bearing Range
Downloadable PDF Catalogue Super Precision Bearings
Downloadable PDF Catalogue Taper Pins
Downloadable PDF Catalogue Thrust Bearings
Downloadable PDF Catalogue Thumb Screws and Nuts
Downloadable PDF Catalogue Timing Belts
Downloadable PDF Catalogue Timing Pulley Stock
Downloadable PDF Catalogue Timing Pulleys
Downloadable PDF Catalogue Vibration Mounts
Downloadable PDF Catalogue Washers
Downloadable PDF Catalogue Wave Washers
Downloadable PDF Cross Reference ADR and SKF
Downloadable PDF Cross Reference Anderton Circlips
Downloadable PDF Cross Reference Barden Bearings
Downloadable PDF Cross Reference Essentra
Downloadable PDF Cross Reference Flocast
Downloadable PDF Cross Reference K&S Metals
Downloadable PDF Cross Reference McMaster Carr
Downloadable PDF Cross Reference Miniature Precison Bearings
Downloadable PDF Cross Reference Nordex
Downloadable PDF Cross Reference NSK and NTN
Downloadable PDF Cross Reference Ondrives
Downloadable PDF Cross Reference Reid Supply
Downloadable PDF Cross Reference SDP-SI Designatronics
Downloadable PDF Cross Reference Seeger Circlips
Downloadable PDF Cross Reference Sintered Bronze
Downloadable PDF Cross Reference Small Parts Inc
Downloadable PDF Cross Reference Timing Belts and Pulleys
Freight Rates and Shipping Times
Frequently Asked Questions
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 129514 products in 2148 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
