Belts Rounthane Categories
Belts - Rounthane
Joinable belting. 88 Shore A hardness. Yellow colour. Temperature range -31 to 65 Deg C (-25 to 150 Deg F).
Join with Rounthane Connectors (purchased separately). Material : Non Slip Polyurethane. Use with grooved idler pulleys with diameters at least 8 times the belt width. Purchased per 305mm (1 foot). Orders for more than 1 foot will be supplied as a continuous length. FDA / USDA approved.
Related Information:
You may also be interested in
Pulleys Grooved
Pulleys - U Groove - Idler - Steel - With Bearing
Steel with Steel Ball Bearings
Use with round belts such as Rounthane or O-Rings.
Related Information:
Pulleys - U Groove - Idler - Plastic - With Ball Bearing
Plastic and Steel with Steel Ball Bearings or Plain Bearings.
Use with round belts such as Rounthane or O-Rings.
Related Information:
Pulleys - U Groove - Idler - Plastic - With Plain Bore
Plastic and Steel with Steel Ball Bearings or Plain Bearings.
Use with round belts such as Rounthane or O-Rings.
Related Information:
Belts - Poly V - J Section
Belts include a tensile cord, most suited for industrial or adjustable applications
Poly V are ideal for high ratio and high speed drives. J Section is 2.34mm pitch and 3.56mm belt height. Note, this series is not a strechable type of belt.
Related Information:
Belts - Posi-Drive - 4.00 mm Circular Pitch - Double Core
Same as US 20 Pitch - Use with Posi-Drive Sprockets.
Use Double Core with Posi-Drive Sprockets. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined.
Related Information:
Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core
Same as US 20 Pitch - Use with Posi-Drive Pulleys.
Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined.
Related Information:
Belts - Vee - 10.0 x 5.5mm - M-3L
Miniature and small belts. 10.0mm Top Width x 5.5mm Height.
Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.
Related Information:
Belts - Vee - 10.0 x 6.0mm - Z
Miniature and small belts. 10.0mm Top Width x 6.0mm Height.
Sizes are nominal and may vary slightly.
Related Information:
Belts - Vee - 12.5 x 9.0mm - A-4L
12.5mm Top Width x 9.0mm Height.
Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.
Related Information:
Belts - Vee - 16.5 x 11.0mm - B
16.5mm Top Width x 11.0mm Height.
Sizes are nominal and may vary slightly.
Related Information:
Belts - Vee - 31.5 x 19.0mm - D
31.5mm Top Width x 19.0mm Height.
Sizes are nominal and may vary slightly.
Related Information:
Belts - Vee - 8.0 x 4.0mm
Miniature and small belts. 8.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly.
Related Information:
Belts - Wedge - 12.7 x 10.0mm - SPA
12.7mm Top Width x 10.0mm Height.
Sizes are nominal and may vary slightly.
Related Information:
Belts - Wedge - 16.3 x 13.0mm - SPB - 5V
16.3mm Top Width x 13.0mm Height.
Sizes are nominal and may vary slightly.
Related Information:
Belts - Wedge - 25.4 x 22.2mm - SPP-8V
25.4mm Top Width x 22.2mm Height.
Sizes are nominal and may vary slightly.
Related Information:
Belts - Wedge - 9.5 x 7.9mm - Notched XPZ - 3VX
Miniature and small belts. 9.5mm Top Width x 7.9mm Height.
Related Information:
Belts - Wedge - 9.7 x 8.0mm - SPZ - 3V
Miniature and small belts. 9.7mm Top Width x 8.0mm Height.
Sizes are nominal and may vary slightly.
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 3.2mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 4.8mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 6.4mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 7.9mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Pitch (P) - 2.073mm (0.0816 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 10.000mm Pitch - AT10 - 10mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 10.000mm Pitch - AT10 - 12mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 10.000mm Pitch - AT10 - 16mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 10.000mm Pitch - AT10 - 20mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 10.000mm Pitch - AT10 - 25mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 10.000mm Pitch - AT10 - 32mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 10.000mm Pitch - AT10 - 50mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 10.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 5.000mm Pitch - AT5 - 10mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 5.000mm Pitch - AT5 - 12mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 5.000mm Pitch - AT5 - 16mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 5.000mm Pitch - AT5 - 20mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 5.000mm Pitch - AT5 - 25mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 5.000mm Pitch - AT5 - 6mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 5.000mm Pitch - AT5 - 8mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Pitch (P) - 5.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm.
Related Information:
Belts - Timing - 14.000mm Pitch - GT2 - 115mm Wide
GT2 Series Metric Timing Belts
Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 14.000mm Pitch - GT2 - 170mm Wide
GT2 Series Metric Timing Belts
Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 14.000mm Pitch - GT2 - 40mm Wide
GT2 Series Metric Timing Belts
Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 14.000mm Pitch - GT2 - 55mm Wide
GT2 Series Metric Timing Belts
Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 14.000mm Pitch - GT2 - 85mm Wide
GT2 Series Metric Timing Belts
Pitch (P) - 14.000mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 2.000mm Pitch - GT2 - 16mm Wide
GT2 Series Metric Timing Belts.
Pitch (P) - 2.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 2.000mm Pitch - GT2 - 3mm Wide
GT2 Series Metric Timing Belts.
Pitch (P) - 2.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. Breaking strength is not indicative of working strength.
Related Information:
Belts - Timing - 2.000mm Pitch - GT2 - 4mm Wide
GT2 Series Metric Timing Belts.
Pitch (P) - 2.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. For easy ready selected sets of timing belts and pulleys please see the HES website.
Related Information:
Belts - Timing - 2.000mm Pitch - GT2 - 6mm Wide
GT2 Series Metric Timing Belts.
Pitch (P) - 2.000mm. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. Breaking strength is not indicative of working strength.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127063 products in 2368 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
