Belts Rounthane Categories
Rounthane Belts
Joinable belting. 88 Shore A hardness. Yellow colour. Temperature range -31 to 65 Deg C (-25 to 150 Deg F).
Join with Rounthane Connectors (purchased separately). Material : Non Slip Polyurethane. FDA / USDA approved. Use with grooved idler pulleys with diameters at least 8 times the belt width. Purchased per 305mm (1 foot) of length. Orders for more than one length of 305mm will be supplied as a continuous length. We can obtain more than shown in stock, please contact us for a quotation.
Related Information:
Rounthane Connectors
Joinable belting connectors.
This category may be available in the new MBA online store at Rounthane Connectors.
Related Information:
Belts - Round - Urethane - Seamless
Seamless round belting. Yellow colour. Temperature range -31 to 70 Deg C (-25 to 158 Deg F).
Working Load is 8 Percent of Tensile Strength. Use with grooved idler pulleys with diameters at least 8 times the belt width. This category may be available in the new MBA online store at Belts - Round - Urethane - Seamless.
Related Information:
Pulleys - U Groove - Idler - Steel - With Bearing
Steel with Steel Ball Bearings
Use with round belts such as Rounthane or O-Rings. This category may be available in the new MBA online store at Pulleys - U Groove - Idler - Steel - With Bearing.
Related Information:
Pulleys - U Groove - Idler - Double - Aluminium - With Bearing
Aluminium with Stainless Ball Bearings
Use with round belts such as Rounthane or O-Rings. This category may be available in the new MBA online store at Pulleys - U Groove - Idler - Double - Aluminium - With Bearing.
Related Information:
Pulleys - U Groove - Idler - Double - Stainless - With Bearing
Stainless with Stainless Ball Bearings
Use with round belts such as Rounthane or O-Rings. This category may be available in the new MBA online store at Pulleys - U Groove - Idler - Double - Stainless - With Bearing.
Related Information:
Pulleys - U Groove - Idler - Plastic - With Ball Bearing
Plastic and Steel with Steel Ball Bearings or Plain Bearings.
Use with round belts such as Rounthane or O-Rings. This category may be available in the new MBA online store at Pulleys - U Groove - Idler - Plastic - With Ball Bearing.
Related Information:
Pulleys - U Groove - Idler - Plastic - With Plain Bore
Plastic and Steel with Steel Ball Bearings or Plain Bearings.
Use with round belts such as Rounthane or O-Rings. This category may be available in the new MBA online store at Pulleys - U Groove - Idler - Plastic - With Plain Bore.
Related Information:
Belts - Poly V - J Section
Belts include a tensile cord, most suited for industrial or adjustable applications
Poly Vee are ideal for high ratio and high speed drives. J Section polyvee is 2.34mm pitch and 3.56mm belt height. Note, this series is not a strechable type of belt. The belt width wll be determined by the number of ribs x the pitch. This category may be available in the new MBA online store at Belts - Poly V - J Section.
Related Information:
Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core
Same as US 20 Pitch - Use with Posi-Drive Pulleys.
Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined. This category may be available in the new MBA online store at Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core.
Related Information:
Belts - Vee - 10.0 x 5.5mm - M-3L
Miniature and small belts. 10.0mm Top Width x 5.5mm Height.
Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.
Related Information:
Belts - Vee - 12.5 x 9.0mm - A-4L
12.5mm Top Width x 9.0mm Height.
Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.
Related Information:
Belts - Vee - 12.7 x 7.9mm - Notched AX
12.7mm Top Width x 7.9mm Height.
This category may be available in the new MBA online store at Belts - Vee - 12.7 x 7.9mm - Notched AX.
Related Information:
Belts - Vee - 15.9 x 10.3mm - Notched BX
15.9mm Top Width x 10.3mm Height.
This category may be available in the new MBA online store at Belts - Vee - 15.9 x 10.3mm - Notched BX.
Related Information:
Belts - Vee - 16.5 x 11.0mm - B
16.5mm Top Width x 11.0mm Height.
Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Vee - 16.5 x 11.0mm - B.
Related Information:
Belts - Vee - 22.2 x 13.5mm - Notched CX
22.2mm Top Width x 13.5mm Height.
This category may be available in the new MBA online store at Belts - Vee - 22.2 x 13.5mm - Notched CX.
Related Information:
Belts - Vee - 31.5 x 19.0mm - D
31.5mm Top Width x 19.0mm Height.
Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Vee - 31.5 x 19.0mm - D.
Related Information:
Belts - Vee - 8.0 x 4.0mm
Miniature and small belts. 8.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Vee - 8.0 x 4.0mm.
Related Information:
Belts - Wedge - 12.7 x 10.0mm - SPA
12.7mm Top Width x 10.0mm Height.
Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Wedge - 12.7 x 10.0mm - SPA.
Related Information:
Belts - Wedge - 15.9 x 13.5mm - Notched 5VX
15.9mm Top Width x 13.5mm Height.
This category may be available in the new MBA online store at Belts - Wedge - 15.9 x 13.5mm - Notched 5VX.
Related Information:
Belts - Wedge - 16.3 x 13.0mm - SPB - 5V
16.3mm Top Width x 13.0mm Height.
Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Wedge - 16.3 x 13.0mm - SPB - 5V.
Related Information:
Belts - Wedge - 25.4 x 22.2mm - SPP-8V
25.4mm Top Width x 22.2mm Height.
Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Wedge - 25.4 x 22.2mm - SPP-8V.
Related Information:
Belts - Wedge - 9.5 x 7.9mm - Notched XPZ - 3VX
Miniature and small belts. 9.5mm Top Width x 7.9mm Height.
This category may be available in the new MBA online store at Belts - Wedge - 9.5 x 7.9mm - Notched XPZ - 3VX.
Related Information:
Belts - Wedge - 9.7 x 8.0mm - SPZ - 3V
Miniature and small belts. 9.7mm Top Width x 8.0mm Height.
Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Wedge - 9.7 x 8.0mm - SPZ - 3V.
Related Information:
Belts - Inch Timing - 2.073mm Pitch 40DP - 3.2mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).
Related Information:
Belts - Inch Timing - 2.073mm Pitch 40DP - 4.8mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).
Related Information:
Belts - Inch Timing - 2.073mm Pitch 40DP - 6.4mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).
Related Information:
Belts - Inch Timing - 2.073mm Pitch 40DP - 7.9mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).
Related Information:
Belts - Metric Timing - 10.000mm Pitch - AT10 - 10mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.
Related Information:
Belts - Metric Timing - 10.000mm Pitch - AT10 - 12mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.
Related Information:
Belts - Metric Timing - 10.000mm Pitch - AT10 - 16mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.
Related Information:
Belts - Metric Timing - 10.000mm Pitch - AT10 - 20mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.
Related Information:
Belts - Metric Timing - 10.000mm Pitch - AT10 - 25mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.
Related Information:
Belts - Metric Timing - 10.000mm Pitch - AT10 - 32mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.
Related Information:
Belts - Metric Timing - 10.000mm Pitch - AT10 - 50mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 2.50mm. Belt Height (W) - 4.50mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 10.000mm.
Related Information:
Belts - Metric Timing - 5.000mm Pitch AT5 - 10mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Metric Timing - 5.000mm Pitch AT5 - 12mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Metric Timing - 5.000mm Pitch AT5 - 16mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Metric Timing - 5.000mm Pitch AT5 - 20mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Metric Timing - 5.000mm Pitch AT5 - 25mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Metric Timing - 5.000mm Pitch AT5 - 6mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Metric Timing - 5.000mm Pitch AT5 - 8mm Wide
AT Synchroflex Generation III Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.70mm - Corner Radii ( r )- 0.60mm. Pitch (P) - 5.000mm.
Related Information:
Belts - Metric Timing - 14.000mm Pitch GT - 115mm Wide
GT2 and GT3 Series Metric Timing Belts
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.
Related Information:
Belts - Metric Timing - 14.000mm Pitch GT - 170mm Wide
GT2 and GT3 Series Metric Timing Belts
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.
Related Information:
Belts - Metric Timing - 14.000mm Pitch GT - 40mm Wide
GT2 and GT3 Series Metric Timing Belts
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.
Related Information:
Belts - Metric Timing - 14.000mm Pitch GT - 55mm Wide
GT2 and GT3 Series Metric Timing Belts
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.
Related Information:
Belts - Metric Timing - 14.000mm Pitch GT - 85mm Wide
GT2 and GT3 Series Metric Timing Belts
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.
Related Information:
Belts - Metric Timing - 2.000mm Pitch GT - 3mm Wide
GT2 and GT3 Series Metric Timing Belts.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 2.000mm.
Related Information:
Belts - Metric Timing - 2.000mm Pitch GT - 4mm Wide
GT2 and GT3 Series Metric Timing Belts.
Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 2.000mm.
Related Information:
Belts - Metric Timing - 2.000mm Pitch GT - 6mm Wide - Clean
PowerGrip(R) TruMotion(R) Timing Belts in 2.000mm.
The TruMotion(R) belt construction utilizes a cream-colored polymer compound reinforced with fiberglass tensile cord and a clean polymer-free nylon tooth facing. The belt can withstand high and low temperature ranges of -40oF to +220oF, has a virtually dust-free operation and is non-marking. The belt also has a high flex life and resistance to elongation. GT3 will replace GT2 as stock is depleted. Pitch (P) - 2.00mm, Tooth Height (H) - 0.76mm, Belt Height (W) - 1.52mm. Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength.
Related Information:
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153564 products in 2094 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
