Linear Slides
Compact economical Posi Drive Stages take the work out of designing linear motion control systems.
These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.
Compact economical Posi Drive Stages take the work out of designing linear motion control systems.
These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.
You may also be interested in
Belts Poly Vee
Belts include a tensile cord, most suited for industrial or adjustable applications
Poly V are ideal for high ratio and high speed drives. J Section is 2.34mm pitch and 3.56mm belt height. Note, this series is not a strechable type of belt.
Pulleys Poly Vee
Poly V drives are ideal for high ratio drives and high speed. J Section is 2.34mm pitch and 3.56mm belt height.
Pulleys Timing AT10 10mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing AT5 5mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
HTD 5mm series Flanges can be used with this stock.
Related Information:
Pulleys Timing GT2 2mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing GT2 3mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing GT2 5mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing H Pitch 12.7mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing HTD 3mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing HTD 5mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing HTD 8mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing L Pitch 9.53mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing MXL Pitch
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Pulleys Timing T10 10mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing T2.5 2.5mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing T5 5mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing 40DP LT Pitch
For manufacture of timing pulleys or applications requiring multiple belts from a single drive. Also known as LT.
Related Information:
Pulleys Timing GT2 2mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing GT2 5mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing H Pitch 12.7mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing HTD 3mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing HTD 5mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing HTD 8mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing L Pitch 9.53mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Timing XL Pitch 5.08mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Belts Posi-Drive
Same as US 20 Pitch - Use with Posi-Drive Sprockets.
Use Double Core with Posi-Drive Sprockets. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined.
Related Information:
Same as US 20 Pitch - Use with Posi-Drive Pulleys.
Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined.
Related Information:
Pulleys Timing XL Pitch 5.08mm
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys Poly Vee
Use with QD bush to suit your bore requirement
Poly V drives are ideal for high ratio drives and high speed. J Section is 2.34mm pitch and 3.56mm belt height.
Positioning
Used for Gauging and Positioning Light to Medium Loads.
Spring loaded micrometer drives allow precise repeatable adjustments with low friction and zero backlash. Positioning Slides can be stacked for Multi axis applications. Preloaded positioning slides fully assemebled. Black Anodized Finish.
Rollers
Neoprene 60 durometer black ground outside diameter drive rollers
Tensioners
Use with idler shafts and idler pulleys. Fixed base with adjustable arm through 360o.
Idler shaft and pulleys not included with tensioner.
Related Information:
Use with idler shafts and idler pulleys. With flanged base that can be mounted in a tight area.
Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360o controlled tensioning. Serrated teeth to prevent slippage once tightened.
Related Information:
Use with idler shafts and idler pulleys. Adjusting slot assists with precise adjustments.
Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360o controlled tensioning. Serrated teeth to prevent slippage once tightened.
Related Information:
Use with idler shafts and idler pulleys. Mounts on any free point of a fixed shaft allowing controlled tensioning around 360o.
Idler shaft and pulleys not included with tensioner.
Related Information:
Pins Dowel
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
Used to replace screws where the need to remove the pin is unlikely.
Stainless Steel 304 Grade. Simple, low cost assembly. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
Related Information:
Couplings Other
1.88mm bore press fits most standard hobby motors (2mm shaft)
Plungers Spring
Items shown with Long-Lok have a dry threadlocking sealant applied to thread.
Thread Inserts
Made from stress proof steel. The power drive tool is used for volume installation of EZ-LOK thread inserts.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Brass. Install with a screwdriver. Superior holding power in hard and soft woods, particle board and other wood products. Long pilot assists with straight driving into a drilled hole.
Screws Countersunk
Flat Head Countersunk. Metric only. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Nuts sold seperately - See Nuts. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.
Related Information:
Screws Pan Head
Metal Thread Screws. Metric only. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Nuts sold seperately - See Nuts. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.
Related Information:
Gear Blanks
Blanks for cutting gears and pulleys and friction drives.
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2o. Approx Max Temperature 80 oC. Suitable for manual and short term drive application.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 124479
products in 2754 categories including
ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.