BEF08LH RINO
Cross Referenced Part Numbers
RINO part number BEF-08-LHMatches our part number
Eye Size (d1): 8.000. Overall Length (L): 47.00. Thread Size (T): M8x1.25 Left.
Part Link: REF-080-L-CB
Retail Price: 0.00
Lower price for quantities
Stock: 1
Lower price for quantities
Stock: 1
Category Matches
Gearbox Parts
P30-60 Rino Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Spring Motors
Spring Motor Assemblies - Open - RINO
Budget Assemblies. Average fatigue life of 5000 to 30000 cycles.
Springs : 301 Stainless Steel. Average fatigue life of 5,000 to 30,000 cycles.
Belts - Timing - 5.080mm Pitch - XL - 6.4mm Wide
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Belts - Timing - 5.080mm Pitch - XL - 7.9mm Wide
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Belts - Timing - 5.080mm Pitch - XL - 9.5mm Wide
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Belts - Timing - 5.080mm Pitch - XL Double Sided - 9.5mm Wide
Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Pulleys - Timing - 5.080mm Pitch - XL - 6.4mm Wide - Through Bore
Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide.
Aluminium alloy. Finished bore with set screw locking.
Related Information:
Pulleys - Timing - 5.080mm Pitch - XL - 9.5mm Wide - Plastic - Insert
Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Brass insert.
Related Information:
Pulleys - Timing - 5.080mm Pitch - XL - 9.5mm Wide - Through Bore
Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide.
Aluminium alloy and Black Oxide coated steel. Finished bore with set screw locking. Unfinished types requires drilling and tapping. Bore requires machining to finished size.
Related Information:
Pulleys - Timing - 5.080mm Pitch - XL - STOCK - Aluminium
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Pulleys - Timing - 5.080mm Pitch - XL - STOCK - Carbon Steel
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Tools - Nut Drivers
Includes socket wrench for 0-80 size screws
Lengths shown are based on standard stock but may vary.
Housings - Bearing - Single Assembly
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
Circlips - External - Inverted
N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel. Retaining rings. Snap Rings (USA).
Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips.
Related Information:
Circlips - Internal - Inverted
M1308 / JV / INTV / BN830. Retaining rings. Snap Rings (USA).
Inverted lugs seat into the groove for better clearance and cleaner appearance. Good for shielded bearings that pass tightly through the bore or housing. Use recommended installation pliers.
Related Information:
Flanges - Timing Pulley - Suit 5.080mm XL Series - Aluminium
Use with timing pulley stock to custom make your own pulleys
Related Information:
Flanges - Timing Pulley - Suit 5.080mm XL Series - Carbon Steel
Use with timing pulley stock to custom make your own pulleys
Related Information:
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock
Match with 12.70x7.75mm simplex chain (08B BS)
Taperlock Bored sprockets need to be matched up with a taperlock bush to obtain the correct bore size. British Standard 08B - 1/2 inch.
Related Information:
Tools - Die Nuts
Tungsten Chrome Alloy - Carbon Steel die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore
Match with 12.70x7.75mm duplex chain (08B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch.
Related Information:
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Match with 12.70x7.75mm simplex chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
Related Information:
Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Match with 12.70x7.75mm simplex chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
Related Information:
Check Size Before Ordering BB30 Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Check Size Before Ordering BMX MID Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Check Size Before Ordering Canondale Lefty Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Check Size Before Ordering DT Swiss Hubs Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Check Size Before Ordering FSA Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Check Size Before Ordering Giant Tapered OD2 Road Overdrive2 Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Check Size Before Ordering Shimano External BB Pre 2006 Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Check Size Before Ordering Specialized Roubaix Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Check Size Before Ordering Sram Truvativ Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Tools - Dies - Carbon Steel
Tungsten Chrome Alloy - Carbon Steel Button dies and die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
Latches - 1-4 Turn - Simple
With 5.08mm offset cam. Cam may be reversed for increased grip range. Includes detent in body which signals positive open or closed position.
The catch on these latches may be supplied either standard, inverted or flat depending on the grip range. Catches are not reversible.
Attachments - Cable - Threaded Plugs
Use with synchromesh or standard miniature cable
F and L dimensions are obtained after swaging. Before swaging the fitting is round.
Related Information:
Belts - Timing - 2.032mm Pitch - MXL - 19.1mm Wide
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 19.1mm (3/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Belts - Timing - 2.032mm Pitch - MXL - 3.2mm Wide
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 3.18mm (1/8 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Belts - Timing - 2.032mm Pitch - MXL - 4.8mm Wide
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 4.76mm (3/16 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Belts - Timing - 2.032mm Pitch - MXL - 6.4mm Wide
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Belts - Timing - 2.032mm Pitch - MXL - 7.9mm Wide
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 7.93mm (5/16 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Belts - Timing - 2.032mm Pitch - MXL - 9.5mm Wide
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 9.53mm (3/8 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 3.2mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 4.8mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 6.4mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).
Related Information:
Belts - Timing - 2.073mm Pitch - 40DP - 7.9mm Wide
Standard Series Timing Belts 2.072mm or 0.0816 inch pitch. Also known as LT.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Pitch (P) - 2.073mm (0.0816 inch).
Related Information:
Balls - Plastic - Acrylic
Resistance to weather and sunlight. Good abrasion resistance.
Diametrical tolerances typically + / - 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.
Related Information:
Housings - Bearing - Square - Miniature
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
Tube - Round - Stainless Steel
Hollow round tubing for general hobby applications.
For general hobby applications. Includes K&S Metals range and more. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft.
Related Information:
Belts - Timing - 2.032mm Pitch - MXL Double Sided - 6.4mm Wide
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.51mm. Belt Height (W) - 1.52mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Contact Us
Charity
Dental Bearings
Dowel Pins
Downloadable PDF Catalogue Ball Lock Pins
Downloadable PDF Catalogue Balls
Downloadable PDF Catalogue Ceramic Bearings
Downloadable PDF Catalogue Circlips
Downloadable PDF Catalogue Corrosion Resistant Bearings
Downloadable PDF Catalogue Disc Springs
Downloadable PDF Catalogue Dowel Pins
Downloadable PDF Catalogue Economy Bearings
Downloadable PDF Catalogue Hammer Drive Pins
Downloadable PDF Catalogue High Speed Bearings
Downloadable PDF Catalogue Key Steel
Downloadable PDF Catalogue Knobs
Downloadable PDF Catalogue Leveling Mounts
Downloadable PDF Catalogue Metallic Bushes
Downloadable PDF Catalogue O-Rings
Downloadable PDF Catalogue Pins
Downloadable PDF Catalogue Plastic Bearings
Downloadable PDF Catalogue Polyvee Belts and Pulleys
Downloadable PDF Catalogue Precision Shim Washers
Downloadable PDF Catalogue Push On and Push In Rings
Downloadable PDF Catalogue Rod & Tube
Downloadable PDF Catalogue Roll Pins
Downloadable PDF Catalogue Shaft Collars
Downloadable PDF Catalogue Shim Sheet
Downloadable PDF Catalogue Shoulder Screws
Downloadable PDF Catalogue Sintered Bronze Bushes
Downloadable PDF Catalogue Socket Set Screws
Downloadable PDF Catalogue Solid Bronze Bushes
Downloadable PDF Catalogue Spring Steel Strip
Downloadable PDF Catalogue Springs
Downloadable PDF Catalogue Standard Ball Bearing Range
Downloadable PDF Catalogue Super Precision Bearings
Downloadable PDF Catalogue Taper Pins
Downloadable PDF Catalogue Thrust Bearings
Downloadable PDF Catalogue Thumb Screws and Nuts
Downloadable PDF Catalogue Timing Belts
Downloadable PDF Catalogue Timing Pulley Stock
Downloadable PDF Catalogue Timing Pulleys
Downloadable PDF Catalogue Vibration Mounts
Downloadable PDF Catalogue Washers
Downloadable PDF Catalogue Wave Washers
Downloadable PDF Cross Reference ADR and SKF
Downloadable PDF Cross Reference Anderton Circlips
Downloadable PDF Cross Reference Barden Bearings
Downloadable PDF Cross Reference Essentra
Downloadable PDF Cross Reference Flocast
Downloadable PDF Cross Reference K&S Metals
Downloadable PDF Cross Reference McMaster Carr
Downloadable PDF Cross Reference Miniature Precison Bearings
Downloadable PDF Cross Reference Nordex
Downloadable PDF Cross Reference NSK and NTN
Downloadable PDF Cross Reference Ondrives
Downloadable PDF Cross Reference Reid Supply
Downloadable PDF Cross Reference SDP-SI Designatronics
Downloadable PDF Cross Reference Seeger Circlips
Downloadable PDF Cross Reference Sintered Bronze
Downloadable PDF Cross Reference Small Parts Inc
Downloadable PDF Cross Reference Timing Belts and Pulleys
Freight Rates and Shipping Times
Frequently Asked Questions
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 129827 products in 2148 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
