BDB60 REID

60 and 70 Borden Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Rollers - Drive

Also see combined categories:
All Rollers

Neoprene 60 durometer black ground outside diameter drive rollers

Mounts - Buffer - Male - Conical

Also see combined categories:
All Cylindrical Mounts

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening

Related Information:

Cylindrical Bobbin Mounts PDF Quick Guide

Mounts - Bobbin - Male - Square Base

Also see combined categories:
All Cylindrical Mounts

Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening

Fastener may be steel, brass or zinc plated. Natural Rubber isolator.

Related Information:

Cylindrical Bobbin Mounts PDF Quick Guide

Bushes - Stainless Steel and PTFE - Flanged

Also see combined categories:
All Steel Bushes
All Flanged Steel Bushes

Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.

Operating Temperature -200^o to 280^o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating. Speed Limit in oil 4.5 metres surface speed per second.

Related Information:

Metallic Bushes PDF Catalogue

Bushes - Stainless Steel and PTFE - Unflanged

Also see combined categories:
All Steel Bushes
All Unflanged Steel Bushes

Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.

Operating Temperature -200^o to 280^o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating. Speed Limit in oil 4.5 metres surface speed per second.

Related Information:

Metallic Bushes PDF Catalogue

Gearmotors - DC PM - Size 70x114

Also see combined categories:
All DC Permanent Magnet Gearmotors

Permanent Magnet.

Max. Allowable Radial Load: 100N (10mm from mounting surface). Max. Allowable Axial Load: 30N. Axial Play: 0.05 - 0.6mm. Allowable Temperature Range: -20^oC to +60^oC. Integral CD PM Motor - Brush type commutation - 12 segment commutator - RFI protection standard. Gear train with steel and high quality plastic gears - Terminal dimensions 4.8 x 0.8 - Weight: 1200g.

Straight Handpiece 6000 RPM W.H. Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Inserts - Self Tapping - For Wood - Slotted Drive

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60^o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.

Related Information:

Installation Tools

TT600 Yamaha Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

HA6000A Reelemin Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

UC4600C Abu Garcia Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

P30-60 Ondrives Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

P30-60 Rino Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

360 Polaris Pool Cleaner Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

C60 Polaris Pool Cleaner Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Balls - Chrome Steel

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 60-70.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.

Related Information:

AFBMA Ball Grades

Balls Master Catalogue PDF

Inserts - Self Tapping - For Aluminium - Stainless 303

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60^o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.

Related Information:

Installation Tools

Inserts - Self Tapping - For Plastics - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60^o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.

Related Information:

Installation Tools

Inserts - Self Tapping - For Aluminium - Stainless 316

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60^o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.

Related Information:

Installation Tools

Inserts - Self Tapping - For Aluminium - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60^o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.

Related Information:

Installation Tools

Screws - Captive - Retractable - Steel

Also see combined categories:
All Captive Screws

Compliance with UL 1950 and EN 60950 codes for access areas. Ratchet mechanism allows screw to be tightened down by hand, but a tool is needed to loosen.Fully retractable captive to the panel and spring ejected.

Press in style. Bright chromate zinc plated, case hardened steel with aluminium knob and stainless steel spring. Knobs available either slotted or no.2 phillips.

Collars - Shaft - Gripfast - ABS Plastic

Also see combined categories:
All Round Bore Shaft Collars

Self Locking - Quick Release.

265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.

Related Information:

Shafting

Rail Supports - With Shaft - One Piece

Also see combined categories:
All Shaft Supports

One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.

Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments.

Related Information:

Linear Bearing in Housing

Linear Bearings

Frelon Linear Bearings

Bearings - Linear - Ball - Stainless Steel - Closed

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 ^oC Intermittent, 80 Deg C continuous.

Related Information:

Precision Shafting To Suit Bearings

Linear Slides - Utilitrak - PW - Crowned - Channel - Aluminium

Use with Utilitrak PW Crowned Carriages. 6063-T6 aluminium alloy. Economical choice for light duty applications.

Related Information:

Utilitrak PW Crowned Carriages

Shafting - Aluminium - Ceramic Coated

Also see combined categories:
All Shafting
All Aluminium Shafting

Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.

Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.

Related Information:

Frelon Gold Linear Bearings

Shafting - Aluminium - Ceramic Coated - Tapped

Also see combined categories:
All Shafting
All Aluminium Shafting

Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.

Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.

Related Information:

Frelon Gold Linear Bearings

Linear Slides - Utilitrak - PW - Dual Vee - Channel - Aluminium

Use with Utilitrak PW Dual Vee Carriages. 6063-T6 aluminium alloy. Economical choice for light duty applications.

Related Information:

Utilitrak PW Dual Vee Carriages

Leadscrew Nut Flanges for Acme Supernuts

Also see combined categories:
All Leadscrew Nut Flanges

Flanges for Acme leadscrew thread supernuts metric and imperial

MATERIAL - Aluminum 6062-T6. These flanges are screwed onto the outer thread of the red leadscrew nuts. This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved.

Related Information:

Imperial Acme Supernuts

Calcutta 50-100-150-200-250-251-400-600 Shimano Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Housings - Bearing - Square - Miniature

Aluminium housings to suit standard radial ball bearings.

Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.

Linear Guide System - Two Piece

Using Frelon Gold plain bearing technology. Rail and carriage are made from 6063-T6 aluminium and come as a set.

Rails are ceramic coated to resist corrosion and repel weld spatter and contaminants. Smooth running. Dampens vibration. Guide has slots for T nuts or bolts. Two component system allows for easier installation than traditional rail systems.

Oil Seals - Fluoroelastomer Rubber

Also see combined categories:
All Oil Seals

DIN 3760 - High Temperature and chemical resistance.

Operating Temp. Range: -20^oC to +240^oC. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Suitable for synthetic and hydraulic fluids, strong acids, steam, many chemicals and many alkalis.

Oil Seals - Nitrile Rubber

Also see combined categories:
All Oil Seals

DIN 3760 - General purpose grease and oil sealing. Note - metal cased and rubber cased seals may be interchanged at our discretion. If one or the other is specifically required please let us know when ordering.

Operating Temp. Range: -30^oC to +90^oC. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.

Knobs - Ball - Threaded - Polished Brass

Also see combined categories:
All Female Threaded Ball Knobs

CDA 360 Free Machining Brass

Polished balls are fully finished and suitable for decorative and display purposes.

Related Information:

Knobs PDF Quick Guide by Thread Size

Inserts - Self Tapping - For Plastics - Stainless Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60^o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.

Related Information:

Installation Tools

Bearings - Linear - Ball - Miniature - Super High Precision

Also see combined categories:
All Closed Linear Ball Bearings

High Precision Corrosion Resistant Miniature Linear Bearings.

High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.

Related Information:

Precision Shafting To Suit Bearings

Latches - 200 Series - Heavy Duty

Ultimate strength 660kg. Working strength 265kg.

Heavy Duty.

Housings - Bearing - Pillow Block - Frelon - Standard - Closed

Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. For rotating and linear motion.

Housings - Bearing - Pillow Block - Frelon - Standard - Open

Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. For rotating and linear motion.

Housings - Linear - Square

Also see combined categories:
All Linear Bearing Housings

Used to maintain radial integrity and eliminate the need for parallel shafting.

Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads.

Balls - Stainless Steel - 400 Grade

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 55-60. Includes 420 and 440C grades

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. AISI440C Stainless Steel.

Related Information:

AFBMA Ball Grades

Balls Master Catalogue PDF

Ball Transfer Units - Spring Loaded - Flanged - Zinc Plated

Single ball bearings units for conveyor systems

Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading.

Ball Transfer Units - Spring Loaded - Unflanged - Zinc Plated

Also see combined categories:
All Push Fit Ball Transfers

Single ball bearings units for conveyor systems

Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading.

Circlips - External - Standard - Berryllium Copper

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / N1400 / D1460. Retaining rings. Snap Rings (USA).

Related Information:

Circlip Pliers

Circlips PDF Catalogue

Anderton Cross Reference PDF

Shim and Foil - Aluminium

Also see combined categories:
All Shim
All Sheet

Precision aluminium shim sheet. Very thin to thick sizes.

NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Coloured shim is anodised. The colour is not removable. The colour is for identification purposes only. Includes K&S Metals range and more. Includes listings on 1100, 3003, 6061-T6 and commercial grades aluminium sheet.