Balls Tooling One Piece Standard Stainless Steel Slip Fit Categories
Tooling Balls
Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Balls - Tooling - One Piece - Standard - Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
1144 steel heat treated to 53-57 RC. This category may be available in the new MBA online store at Balls - Tooling - One Piece - Standard - Steel - Slip Fit.
Related Information:
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Balls - Tooling - One Piece - Standard - Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
1144 steel heat treated to 53-57 RC. This category may be available in the new MBA online store at Balls - Tooling - One Piece - Standard - Steel - Press Fit.
Related Information:
Balls - Tooling - One Piece - Shoulder - Stainless Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Balls - Tooling - Two Piece - Standard - Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
1144 steel heat treated to 53-57 RC. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at Balls - Tooling - Two Piece - Standard - Steel - Slip Fit.
Related Information:
Balls - Tooling - Two Piece - Standard - Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
1144 steel heat treated to 53-57 RC. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at Balls - Tooling - Two Piece - Standard - Steel - Press Fit.
Related Information:
Balls - Checking - Stainless Steel - Standard
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at Balls - Checking - Stainless Steel - Standard.
Related Information:
Balls - Tooling - One Piece - Construction - Stainless Steel
High quality tooling balls provide a precise reference point for critical machining operations.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 440C Stainless Steel heat treated to 55-58 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. This category may be available in the new MBA online store at Balls - Tooling - One Piece - Construction - Stainless Steel.
Related Information:
Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. This category may be available in the new MBA online store at Balls - Tooling - One Piece - Shoulder - Steel - Slip Fit.
Related Information:
Balls - Tooling - One Piece - Shoulder - Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. This category may be available in the new MBA online store at Balls - Tooling - One Piece - Shoulder - Steel - Press Fit.
Related Information:
Balls - Tooling - Two Piece - Shoulder - Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. Knurled shoulder. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at Balls - Tooling - Two Piece - Shoulder - Steel - Slip Fit.
Related Information:
Plungers - Ball Threaded - 303 Stainless Steel - Standard - Standard
Items shown with Long-Lok have a dry threadlocking sealant applied to thread.
Bearings - Linear Ball - Stainless Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear Ball - Stainless Steel - Closed.
Related Information:
Balls - Metallic - Stainless Steel - 316L Grade
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. This category may be available in the new MBA online store at Balls - Metallic - Stainless Steel - 316L Grade.
Related Information:
Pins - Ball Lock - T Handle - Industrial - Stainless Steel - Standard
Quick release. Body and spindle 17-4 PH stainless steel. Ring and spring 17-7 MO stainless steel. Handle and collar are 300 grade stainless. Tee handle.
Positive lock detent pins. 300 Grade Stainless Components. 440C Stainless Balls.
Related Information:
Cam Followers - Miniature - Standard
Stainless steel ball type cam followers.
This category may be available in the new MBA online store at Cam Followers - Miniature - Standard.
Balls - Tooling - Two Piece - Shoulder - Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
Precision ground shoulder provides precise C dimension to facilitate locating ball centre line. 1144 steel heat treated to 53-57 RC. Knurled shoulder. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at Balls - Tooling - Two Piece - Shoulder - Steel - Press Fit.
Related Information:
Bearings - Single Row Ball Flanged - Standard - 440C Stainless
Stainless Steel Bearings with Flanges.
Single row radial ball bearings with flanges. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at Bearings - Single Row Ball Flanged - Standard - 440C Stainless.
Related Information:
Bearings - Single Row Ball Unflanged - Standard - 440C Stainless
Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
Stainless steel radial ball bearings
Standard single row radial ball bearings. This category may be available in the new MBA online store at Bearings - Single Row Ball Unflanged - Standard - 440C Stainless.
Related Information:
Balls - Tooling - One Piece - Construction - Steel
High quality tooling balls provide a precise reference point for critical machining operations.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. This category may be available in the new MBA online store at Balls - Tooling - One Piece - Construction - Steel.
Related Information:
Balls - Fixture - Stainless Steel
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at Balls - Fixture - Stainless Steel.
Related Information:
Bearings - Single Row Ball Unflanged - Standard - 316 Stainless - Open
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance.
Related Information:
Bearings - Single Row Ball Unflanged - Standard - 316 Stainless - Sealed
Marine, food and medical grade Stainless Steel - Non Hardenable. Polyethylene plastic seals.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races, greased. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Bearings - Single Row Ball Unflanged - Standard - 316 Stainless - Shields
Marine, food and medical grade Stainless Steel - Non Hardenable. 316 stainless steel shields.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Stainless steel 316 cage, grade 200 type 316 stainless balls, 316 stainless races, 316 stainless steel shields. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Usual supply is unlubricated so that they can be used immediately in applications exposed to water, or lubricated by the user with their preferred grease. Special orders can be run with a selected lubricant. Note that some bearings may already be listed with grease.
Related Information:
Balls - Checking - Stainless Steel - With Tapped Shank
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at Balls - Checking - Stainless Steel - With Tapped Shank.
Related Information:
Bearings - Ball Thrust Grooved - Stainless Steel
3 Piece Thrust Bearings Open Type
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others have identical bores on each race, requiring a stepped shaft. Some have a reduced OD on one race allowing seating into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Ball Thrust Grooved - Stainless Steel.
Related Information:
Bearings - Ball Thrust Flat - Stainless Steel
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing. This category may be available in the new MBA online store at Bearings - Ball Thrust Flat - Stainless Steel.
Related Information:
Slides - Linear - Recirculating Ball - Standard
The BSR precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants. Note BSR1530SL and BSR2040SL can not be mounted from inside of track rail.
Collars - Shaft - Hinged - Stainless Steel
Precision machined. Convenient easy-to-assemble design. 303 Stainless Steel
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
Related Information:
Slides - Linear - Non Recirculating Ball - Standard
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
Bearings - Single Row Ball Unflanged - Standard - Special Anti Corrosion
Higher corrosion resistance than 440C stainless - HRC59 Hardness - Same or higher load than 440C
Ideal for applications with salt spray or chemicals in the pH range 3 to 12. ISC CASSTOP design with special TBN-6H stainless steel. Other sizes available on request.
Related Information:
Locknuts - Stainless Insert
Simplify the assembly and reduce costs involved in securing ball bearings. One piece item where the locking function is performed by a spring peened into the top of the nut.
Nut Body: Low Carbon Steel. Locking Insert: Stainless Steel Hardness HB 201-269. The spring bears on the flank of the shaft thread with force (P) generating reaction force (P’) in the screw threads with a resulting high friction torque (prevailing torque). Unique slim body design. Secure locking without keyway and tab washer. One piece construction reduces stock and allows simpler, quicker assembly. Simple infinite adjustment. Re-usable up to 100 times. Resists vibration and shock. Equally effective for rotation in either direction even with rapid reversals.
Related Information:
Plungers - Ball Threaded - With Limit Switch
Suitable for locking and releasing a device by using a built-in electrical switch. Stainless steel spring, nickel plated body, hardened steel ball.
Supply Cable : Grey for normally open contacts, black for normally closed. Oil resistant. Max tensile load 20N. Working Temperature: -10 deg C to 80 deg C. Electrical Supply : 20 mA DC Max. Switching load recommended 5-10 mA. Voltage : 12-24V Supply Cable 3mm - 2 Phase, 2 metres long. Safety Standard : IP40 Average Switch Life Span : 3 milliion switchings.
Balls - Tooling - Two Piece - Construction - Steel
High quality tooling balls provide a precise reference point for critical machining operations.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.
Related Information:
Circlips - External - Standard - Stainless Steel
Imperial and metric DIN471 / D1400 / N1400 / D1460. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. This category may be available in the new MBA online store at Circlips - External - Standard - Stainless Steel.
Related Information:
Circlips - Internal - Standard - Stainless Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Stainless Steel.
Related Information:
Collars - Shaft - Standard - Stainless Steel
Includes miniature precision types. 303 and 316 Types.
Static torque and axial load are for reference only using steel cup point grub screw on soft steel shaft. This category may be available in the new MBA online store at Collars - Shaft - Standard - Stainless Steel.
Related Information:
Pins - Coiled - Stainless Steel - Standard Duty
Spirol Pins. Coiled roll pin.
This category may be available in the new MBA online store at Pins - Coiled - Stainless Steel - Standard Duty.
Related Information:
Pins - Taper Imperial - Standard - Stainless Steel
Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.
This category may be available in the new MBA online store at Pins - Taper Imperial - Standard - Stainless Steel.
Related Information:
Pins - Side Thrust - Single Sided - Stainless Ball
For holding, clamping and positioning work pieces. Body is black oxide steel.
Stainless ball and stainless spring with black oxide coated steel body. This category may be available in the new MBA online store at Pins - Side Thrust - Single Sided - Stainless Ball.
Related Information:
Screws - Thumb - Knurled - Stainless - Standard - Standard
Stainless steel knurled head thumb screws
This category may be available in the new MBA online store at Screws - Thumb - Knurled - Stainless - Standard - Standard.
Related Information:
Collars - Hex Bore - One Piece - 303 Stainless Steel
This category may be available in the new MBA online store at Collars - Hex Bore - One Piece - 303 Stainless Steel.
Related Information:
Plungers - Spring - Threaded - Stainless - Standard - Standard - Standard - St
303 Stainless Steel.
Items shown with Long-Lok have a dry threadlocking sealant applied to thread.
Collars - Shaft - Clamp Type - One Piece - Stainless Steel
This category may be available in the new MBA online store at Collars - Shaft - Clamp Type - One Piece - Stainless Steel.
Related Information:
Bearings - Double Row Ball Semi Precision - 316 Stainless Steel
Marine, food and medical grade Stainless Steel - Non Hardenable. Open, easier to lubricate. Water lubrication is ok.
Tolerances differ from standard bearing types. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. This category may be available in the new MBA online store at Bearings - Double Row Ball Semi Precision - 316 Stainless Steel.
Related Information:
Gear Racks - 24DP - Stainless - Standard - Standard
20 Degree Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
24 DP. Approx 3.33mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gear Racks - 24DP - Stainless - Standard - Standard.
Gear Racks - 48DP - Stainless - Standard - Standard
20 Degree Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 48 DP. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gear Racks - 48DP - Stainless - Standard - Standard.
Gear Racks - 64DP - Stainless - Standard - Standard
20 Degree Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.
Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 64 DP. Approx 1.25mm between teeth. This category may be available in the new MBA online store at Gear Racks - 64DP - Stainless - Standard - Standard.
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153564 products in 2094 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
