Small Parts & Bearings - an MBA company

Ball Screws Nook Series Categories


Ballscrew - Nook Series - Flanges
Ballscrew - Nook Series - Flanges


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.


Ballscrew - Nook Series - Right Hand
Ballscrew - Nook Series - Right Hand


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

High quality alloy steel, induction hardened to RC 56-60. Protective black oxide finish. Lead accurate by at least 0.00083mm per mm.


Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit
Ballscrew - Nook Series - Nuts - Right Hand Thread - Double Circuit


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.


Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit
Ballscrew - Nook Series - Nuts - Right Hand Thread - Single Circuit


Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.

Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.


Couplings - Reli-a-flex - Short Series - Set Screw Type
Couplings - Reli-a-flex - Short Series - Set Screw Type

Also see combined categories:
All Helical and Slit Couplings

From compact 6mm diameter 0.15Nm Working Torque to 40mm diameter 8.3Nm Working Torque. Reli-a-flex(R).

Aluminium Alloy 7075-T6. Zero backlash, one piece construction. Maximises torsional stiffness without inducing high bearing loads. Over 50,000,000 test cycles at rated load and 80 percent offset without failure. Maintenance Free. Recommended temperature range minus 80 oC to plus 80 Deg C.

Related Information:


Ballscrew - Thomson Saginaw
Ballscrew - Thomson Saginaw

Also see combined categories:
All Ball Screws

Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.

When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.


Ballscrew - Thomson Saginaw - Accessories
Ballscrew - Thomson Saginaw - Accessories

Also see combined categories:
All Ball Screws

Wiper Kits and Flanges for Ball Nuts. Match all components within the Thomson Saginaw range only.



Ballscrew - Thomson Saginaw - Nut
Ballscrew - Thomson Saginaw - Nut

Also see combined categories:
All Ball Screws

Ball Nuts to Suit Thomson Saginaw ball screws. Match all components within the Thomson Saginaw range only.

All Right hand thread only.


Ball Transfer Units - Screw Stem - Brass and Aluminium
Ball Transfer Units - Screw Stem - Brass and Aluminium

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.


Ball Transfer Units - Screw Stem - Stainless - Precision
Ball Transfer Units - Screw Stem - Stainless - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.


Ball Transfer Units - Screw Stem - Steel - Precision
Ball Transfer Units - Screw Stem - Steel - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.


Ballscrew - 16mm Nuts - Pillow Block
Ballscrew - 16mm Nuts - Pillow Block

Also see combined categories:
All Ball Screws

Includes ball nut. Match all components within the 16mm range only.

Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.


Ballscrew - Ground - Dia 4mm - Lead 1mm
Ballscrew - Ground - Dia 4mm - Lead 1mm

Also see combined categories:
All Ball Screws

Not for sale outside of Australia and New Zealand



Socket Set Screws - Rolling Ball Tip - Carbon Steel
Socket Set Screws - Rolling Ball Tip - Carbon Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Rolling ball tip for locating into a hole

Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application.

Related Information:


Socket Set Screws - Rolling Ball Tip - Stainless Steel
Socket Set Screws - Rolling Ball Tip - Stainless Steel

Also see combined categories:
All Rolling Ball Tip Grub Screws
All Grub Screws

Rolling ball tip for locating into a hole

Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application.

Related Information:


Mounts - Universal - For Acme Thread and Ballscrews
Mounts - Universal - For Acme Thread and Ballscrews


Use grade 8 hex socket head cap screws for mounting.



Ballscrew - Ground - Bi-Directional - Dia 8mm - Lead 1mm
Ballscrew - Ground - Bi-Directional - Dia 8mm - Lead 1mm

Also see combined categories:
All Ball Screws

Not for sale outside of Australia and New Zealand



Bearings - Ball - Semi-Ground - Sealed
Bearings - Ball - Semi-Ground - Sealed

Also see combined categories:
All Radial Ball Bearings

Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127



Bearings - Ball - Semi-Ground - Shielded
Bearings - Ball - Semi-Ground - Shielded

Also see combined categories:
All Radial Ball Bearings

Radial ball bearings. This series is precision ground on all contact surfaces except the bore. Recommended for lighter loads and maximum speed of 3000rpm. Bore tolerance is +0.127/-0.000, OD tolerance is +0.000/-0.013 and width is +0.000/-0.127



Slides - Linear - Recirculating Ball - Standard
Slides - Linear - Recirculating Ball - Standard

Also see combined categories:
All Linear Slides

The BSR precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.

Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants. Note BSR1530SL and BSR2040SL can not be mounted from inside of track rail.


Socket Set Screws - Flat Tip - Aligning - Carbon Steel
Socket Set Screws - Flat Tip - Aligning - Carbon Steel

Also see combined categories:
All Flat Aligning Tip Grub Screws
All Grub Screws

Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.

Also known as a flat ball tip set screw or a clamping screw.

Related Information:


Socket Set Screws - Flat Tip - Aligning - Stainless Steel
Socket Set Screws - Flat Tip - Aligning - Stainless Steel

Also see combined categories:
All Flat Aligning Tip Grub Screws
All Grub Screws

Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.

Also known as a flat ball tip set screw or a clamping screw.

Related Information:


Slides - Linear - Non Recirculating Ball - Standard
Slides - Linear - Non Recirculating Ball - Standard

Also see combined categories:
All Linear Slides

The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.

Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.


Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 16mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 25mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 32mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore
Pulleys - Timing - 10.000mm Pitch - AT10 - 50mm Wide - Through Bore

Also see combined categories:
All 10mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT10 Series belts

Aluminium. Zinc Plated Steel Flanges. Plain Hub No Grub Screw. Finished Bore.

Related Information:


Pins - Hammer Drive - Flat Head
Pins - Hammer Drive - Flat Head

Also see combined categories:
All Hammer Drive Pins

Used to replace screws where the need to remove the pin is unlikely.

Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.

Related Information:


Pulleys - Timing - 5.080mm Pitch - XL - 6.4mm Wide - Through Bore
Pulleys - Timing -  5.080mm Pitch - XL -  6.4mm Wide - Through Bore

Also see combined categories:
All XL 5.08mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide.

Aluminium alloy. Finished bore with set screw locking.

Related Information:


Pulleys - Timing - 5.000mm Pitch - AT5 - 10mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 10mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:


Pulleys - Timing - 5.000mm Pitch - AT5 - 16mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 16mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:


Pulleys - Timing - 5.000mm Pitch - AT5 - 25mm Wide - Through Bore
Pulleys - Timing -  5.000mm Pitch - AT5 - 25mm Wide - Through Bore

Also see combined categories:
All 5mm Pitch Timing Pulleys Through Bore

Timing pulleys to suit AT5 Series belts

Aluminium Alloy. Steel Flanges. Hub is unthreaded, you will need to drill and tap with your required locking screw size.

Related Information:


Pulleys - Timing - 5.080mm Pitch - XL - 9.5mm Wide - Through Bore
Pulleys - Timing -  5.080mm Pitch - XL -  9.5mm Wide - Through Bore

Also see combined categories:
All XL 5.08mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide.

Aluminium alloy and Black Oxide coated steel. Finished bore with set screw locking. Unfinished types requires drilling and tapping. Bore requires machining to finished size.

Related Information:


Housings - Bearing - Square - Miniature
Housings - Bearing - Square - Miniature


Aluminium housings to suit standard radial ball bearings.

Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.


Balls - Tooling - Two Piece - Construction - Steel
Balls - Tooling - Two Piece - Construction - Steel

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.

Related Information:


Universal Joints - Single Joint - High Speed - Plain Bore - Stainless
Universal Joints - Single Joint - High Speed - Plain Bore - Stainless

Also see combined categories:
All Universal Joints
All Single Joint Universals

303 Stainless Body with 440 Stainless Balls. Maximum operating angle 30 degrees (45 for hand operated applications). Zero backlash. Sealed lubrication. Light weight and low inertia. Not supplied with set screws or tapped holes.


Related Information:


Linear - Mini Rail - Self-Lubricating - Carriage
Linear - Mini Rail - Self-Lubricating - Carriage


Additional carriages for the Mini-Rail system. Match by rail width.

Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments.

Related Information:


Linear - Mini Rail - Self-Lubricating - Carriage and Rail
Linear - Mini Rail - Self-Lubricating - Carriage and Rail


Comes with one carriage. Spare carriages sold separately - match by rail width.

Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments.

Related Information:


Rail Systems - Type 2 - Linear - Precision - Carriage - Chrome - Narrow
Rail Systems - Type 2 - Linear - Precision - Carriage - Chrome - Narrow


Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination. Thin dense chrome.

Related Information:


Rail Systems - Type 2 - Linear - Precision - Carriage - Chrome - Standard
Rail Systems - Type 2 - Linear - Precision - Carriage - Chrome - Standard


Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination. Thin dense chrome.

Related Information:


Rail Systems - Type 3 - Linear - Precision - Carriage - Carbon Steel - Narrow
Rail Systems - Type 3 - Linear - Precision - Carriage - Carbon Steel - Narrow


Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination.

Related Information:


Rail Systems - Type 3 -Linear - Precision - Carriage - Carbon Steel - Standard
Rail Systems - Type 3 -Linear - Precision - Carriage - Carbon Steel - Standard


Match with rail by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Low drag longitudinal seals protect the the balls and ball path from contamination.

Related Information:


Rail Systems - Type 2 - Linear - Precision - Rails - Chrome Coated
Rail Systems - Type 2 - Linear - Precision - Rails - Chrome Coated


Match with carriage by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Rails are subjected to multiple straightening processes during and after grinding of the ball paths to ensure straight and accurate rails.

Related Information:


Rail Systems - Type 3 - Linear - Precision - Rails - Carbon Steel
Rail Systems - Type 3 - Linear - Precision - Rails - Carbon Steel


Match with carriage by size column 1. Thomson 500 Series provide long life, exceptional rigidity, high dynamic and static load capabilities in all directions.

Accommodates high moment loads and maintains high running accuracy. Improved machine accuracies and rigidity resulting in reduced vibration and extended machine and tool life. Rails are subjected to multiple straightening processes during and after grinding of the ball paths to ensure straight and accurate rails.

Related Information:


Bearings - Linear - Sliding - Stainless - PTFE - Closed
Bearings - Linear - Sliding - Stainless - PTFE - Closed

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.


Bearings - Linear - Sliding - Stainless - PTFE - Open
Bearings - Linear - Sliding - Stainless - PTFE - Open

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.


Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext
Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


Slides - Drawer - Front Disconnect - Friction - 19mm Ext
Slides - Drawer - Front Disconnect - Friction - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext
Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext

Also see combined categories:
All Drawer Slides

Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.

Side mounted two member slide. Positive locking mechanism keeps drawer locked in the open position until actively released. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124539 products in 2753 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 124539 products in 2753 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.