Includes ball nut. Match all components within the 16mm range only.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
You may also be interested in
Ball Screws Rolled
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.
Ball Screw Accessories
Wiper Kits and Flanges for Ball Nuts. Match all components within the Thomson Saginaw range only.
Ball Nuts to Suit Thomson Saginaw ball screws. Match all components within the Thomson Saginaw range only.
All Right hand thread only.
Ball Screws Nook Series
Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.
Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.
Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.
High quality alloy steel, induction hardened to RC 56-60. Protective black oxide finish. Lead accurate by at least 0.00083mm per mm.
Ball Screws Ground
Not for sale outside of Australia and New Zealand
Not for sale outside of Australia and New Zealand
Ball Screws Nook Series
Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.
Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.
Match all components within the Nook Series range only. Match nuts, flanges and screws based on ball circle diameter.
Carburised steel with ball tracks heated to RC 58-60. Protective black oxide finish.
Ball Screw Accessories
Use grade 8 hex socket head cap screws for mounting.
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
Rolling ball tip for locating into a hole
Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application.
Related Information:
Rolling ball tip for locating into a hole
Rolling ball set screws are not designed to bear heavy loads. Used to lightly fasten fragile work pieces. We would recommend testing if you plan to use them in a load bearing application.
Related Information:
Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.
Also known as a flat ball tip set screw or a clamping screw.
Related Information:
Grub screws with a pivoting flat tip. The ball can pivot up to 9 Deg. To fasten the object securely to misaligned parts.
Also known as a flat ball tip set screw or a clamping screw.
Related Information:
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
High quality tooling balls provide a precise reference point for critical machining operations.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.
Related Information:
303 Stainless Body with 440 Stainless Balls. Maximum operating angle 30 degrees (45 for hand operated applications). Zero backlash. Sealed lubrication. Light weight and low inertia. Not supplied with set screws or tapped holes.
Related Information:
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Positive locking mechanism keeps drawer locked in the open position until actively released. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by lifting a lever lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Provide a permanent and proper mating hole for commercial and industrial type quick release ball lock pins. Also called detent pins.
Designed to be used on materials or in applications where the pin does not have anything to lock against. Positive lock detent pins. Pin does not protrude past the bottom of the receptacle so they are ideal for blind hole applications. 303 Stainless Steel. Mounted with screws, rivets or bolts. The quick release ball lock pins are inserted from the flanged end, and the ball extends into the wider opening at the top of the receptacle.
Related Information:
Simplify the assembly and reduce costs involved in securing ball bearings. One piece item where the locking function is performed by a spring peened into the top of the nut.
Nut Body: Low Carbon Steel. Locking Insert: Stainless Steel Hardness HB 201-269. The spring bears on the flank of the shaft thread with force (P) generating reaction force (P’) in the screw threads with a resulting high friction torque (prevailing torque). Unique slim body design. Secure locking without keyway and tab washer. One piece construction reduces stock and allows simpler, quicker assembly. Simple infinite adjustment. Re-usable up to 100 times. Resists vibration and shock. Equally effective for rotation in either direction even with rapid reversals.
Related Information:
Also known as stripper bolts.
Metal Thread Screws. Metric and BSW only. Supplied with nut.
Nuts sold seperately - See Nuts.
Related Information:
BSW and METRIC - Bolts
Related Information:
Also known as stripper bolts.
Also known as stripper bolts.
Also known as stripper bolts.
303 Stainless Steel
Also known as stripper bolts.
Used in construction of tool, jig and fixture work. 4140L heat treated steel with black oxide finish.
Also known as stripper bolts.
The quick and easy way to remove broken screws, bolts, pipes and studs.
Note! You will also need a drill bit of the correct size for each extractor.
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
Related Information:
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
Related Information:
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
Related Information:
Metric - UNC - UNF
Nuts sold seperately - See Nuts. DIN 84.
Related Information:
Flat Head Countersunk UNC - UNF - METRIC - Stainless Steel
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. ISO 10642.
Related Information:
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
Related Information:
Metric Only
Nuts sold seperately - See Nuts.
Related Information:
316L Stainless Steel. Other sizes available on request.
Hexagon socket cap head with low head. Safety improvements and compact size for equipment and devices. May be used in vacuum chamber applications in clean rooms, Flat Panel Displays, Semiconductor production equipment and devices. All clean washed, preventing the inclusion of oil and foreign particles.
Countersunk screws length includes head. ie, the full overall length of the screw.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 125482
products in 2754 categories including
ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.