Used for handling large work in drill presses or band saw machines.
Placed between work and machine so work can be easily moved. Black Oxide finish with 9.525mm hardened steel balls. Balls are exposed both sides of sheet. This category may be available in the new MBA online store at
Parallels - Ball.
You may also be interested in
Bearings Double Row Ball
Related Information:
Hardened and Ground Steel 100 Cr6. Din 7979.
Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin to overcome the problem of pressure build up by trapped air. Hardness 55-62 HRC, HV550-650. Extractable pins may or may not have a flat to vent pressure when pulling. Also known as parallel pins.
Related Information:
Used to maintain radial integrity and eliminate the need for parallel shafting.
Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads. This category may be available in the new MBA online store at
Housings - Linear - Square.
Match with sleeves from the sleeves category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
Match with hubs from the hubs category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
Plastic Dowel Pins - Based on DIN6325 or ISO2338
Related Information:
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5
o. Max Parallel Offset 0.25mm. This category may be available in the new MBA online store at
Couplings - Helical - Standard.
Related Information:
Precision Dowel Pins - 416 Grade - Based on DIN6325 or ISO2338
Related Information:
Precision Dowel Pins - Based on DIN7
Related Information:
Low cost aluminium couplings primarily used for 3D printer stepper motors
Max. Ang Misalignment 5
o. Max Parallel Offset 0.25mm. This category may be available in the new MBA online store at
Couplings - Helical - Economy.
Related Information:
Precision Dowel Pins - 316 Grade - Based on DIN7
Related Information:
Precision Dowel Pins - Based on DIN6325, ISO2338
Related Information:
Used for work feeders for production milling, positioning fixutres, work holding devices, checking fixtures, shuttle devices, assembly equipment, etc.
Tapered gibs are adjusted with a single screw that moves the gib on the taper. This type remains parallel and wears less as it occurs over the entire surface. Made of continuous cast GS 40,000 PSI pearlitic grey iron. Able to be milled, drilled, tapped, etc. This category may be available in the new MBA online store at
Slides - Dovetail.
Precision Dowel Pins - 316 Grade - Based on DIN6325, ISO2338, ISO 8734
Related Information:
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.
Related Information:
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).
Related Information:
Outstanding wear resistance. Good thermal and chemical resistance.
High hardness. Grades shown are AFBMA / ISO3290-1. High strength over a wide temperature range. High fracture toughness. Outstanding wear resistance. Good thermal and chemical resistance.
Related Information:
Outstanding wear resistance. Excellent thermal and chemical resistance.
Related Information:
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2. This category may be available in the new MBA online store at
Balls - Bored - Steel.
Related Information:
Hardness: Rockwell C: 60-70.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833. This category may be available in the new MBA online store at
Balls - Metallic - Chrome Steel.
Related Information:
Please note that ball magnets are not to be used as toys. These are a strong magnet must be kept away from children as serious harm may result from ingestion.
Related Information:
Specific Gravity 8.4
Related Information:
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000
oC. This category may be available in the new MBA online store at
Balls - Metallic - Stainless Steel - 304 Grade.
Related Information:
A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000
oC. This category may be available in the new MBA online store at
Balls - Metallic - Stainless Steel - 316 Grade.
Related Information:
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. This category may be available in the new MBA online store at
Balls - Metallic - Stainless Steel - 316L Grade.
Related Information:
Hardness: Rockwell C: 55-60. Includes 420 and 440C grades
Related Information:
Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Related Information:
Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.
Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent. Threaded either 1-72 UNF or M1.2.
Related Information:
Extreme hardness and wear resistance.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.
Related Information:
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight. This category may be available in the new MBA online store at
Balls - Bored - Plastic.
Related Information:
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Standard Opaque White. Specific Gravity: 1.4.
Related Information:
Resistance to weather and sunlight. Good abrasion resistance.
Diametrical tolerances typically + / - 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.
Related Information:
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
Related Information:
Excellent for liquid level float applications.
Tolerance and sphericity: up to and including 25.4mm diameter = + / -0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.
Related Information:
No water absorption. Temperatures up to 288 Deg C.
Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 oC. Unpolished. Specific Gravity: 2.3.
Related Information:
Polyvinyl chloride. PVC is a chemically stable material, which shows little change in molecular structure, and also exhibits little change in its mechanical strength.
Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. It is easily worked or machined and has good chemical and biological resistance. It is relatively hard and can be polished to a shine. Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. Heat Deflection Temperature 176 F / 80 C. Rockwell Hardness 115. Zero water absorption in 24 hours.
Related Information:
TorlonTM 4301 Bearing Grade Balls. Grade 1.
Polyamide-imide (Torlon
TM< / sup>) Balls. Rockwell Hardness (Method A): E86 or M109-119. Specific Gravity: 1.38. Colour: Brown Opaque. This category may be available in the new MBA online store at Balls - Plastic - Torlon.
Related Information:
A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.
It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .95 g/cc. Hardness, Shore 40D. Tensile Strength 3000 psi. Melting Point 410 F. Rohs Compliant. Not FDA compliant. This grade is slightly harder than the 87A grade. Colour usually red but some sizes are beige.
Related Information:
A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.
It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .96 g/cc. Hardness, Shore 87A. Tensile Strength 2550 psi. Melting Point 400 F. Rohs Compliant and FDA compliant. This grade is slightly softer than the 40D grade. Colour Beige.
Related Information:
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Max Load is applicable when used as a transfer, not as a castor.
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Max Load is applicable when used as a transfer, not as a castor. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at
Ball Transfer Units - Screw Stem - Brass and Aluminium.
Single ball bearings units for conveyor systems
Applications include measuring equipment and light weight coil handlers. Max Load is applicable when used as a transfer, not as a castor. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at
Ball Transfer Units - Screw Stem - Stainless - Precision.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153543
products in 2089 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.