Small Parts & Bearings - an MBA company

Ball Parallels Categories


Parallels - Ball
Parallels - Ball


Used for handling large work in drill presses or band saw machines.

Placed between work and machine so work can be easily moved. Black Oxide finish with 9.525mm hardened steel balls. Balls are exposed both sides of sheet. This category may be available in the new MBA online store at Parallels - Ball.


You may also be interested in

Bearings Double Row Ball




Pins - Dowel - Extractable
Pins - Dowel - Extractable

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6. Din 7979.

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin to overcome the problem of pressure build up by trapped air. Hardness 55-62 HRC, HV550-650. Extractable pins may or may not have a flat to vent pressure when pulling. Also known as parallel pins.

Related Information:


Housings - Linear - Square
Housings - Linear - Square

Also see combined categories:
All Linear Bearing Housings

Used to maintain radial integrity and eliminate the need for parallel shafting.

Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads. This category may be available in the new MBA online store at Housings - Linear - Square.


Couplings - Crowned Tooth Gear - Hubs Only
Couplings - Crowned Tooth Gear - Hubs Only


Match with sleeves from the sleeves category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:


Couplings - Crowned Tooth Gear - Sleeve Only
Couplings - Crowned Tooth Gear - Sleeve Only


Match with hubs from the hubs category

+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.

Related Information:


Couplings - Helical - Standard
Couplings - Helical - Standard

Also see combined categories:
All Helical and Slit Couplings

0.1 to 16.2 Nm.

Zero backlash. Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm. This category may be available in the new MBA online store at Couplings - Helical - Standard.

Related Information:


Pins - Dowel - Standard - 416 Stainless - Chamfered End
Pins - Dowel - Standard - 416 Stainless - Chamfered End

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 416 Grade - Based on DIN6325 or ISO2338

Also known as parallel pins. Also known as parallel pins. This category may be available in the new MBA online store at Pins - Dowel - Standard - 416 Stainless - Chamfered End.

Related Information:


Couplings - Helical - Economy
Couplings - Helical - Economy

Also see combined categories:
All Helical and Slit Couplings

Low cost aluminium couplings primarily used for 3D printer stepper motors

Max. Ang Misalignment 5o. Max Parallel Offset 0.25mm. This category may be available in the new MBA online store at Couplings - Helical - Economy.

Related Information:


Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends
Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - Based on DIN7

Diameter tolerances are m6. Also known as parallel pins. This category may be available in the new MBA online store at Pins - Dowel - Standard - Unhardened Steel - Rounded Both Ends.

Related Information:


Pins - Dowel - Standard - Chamfered End
Pins - Dowel - Standard - Chamfered End

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - Based on DIN6325, ISO2338

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins. This category may be available in the new MBA online store at Pins - Dowel - Standard - Chamfered End.

Related Information:


Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends
Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - Based on DIN7

Diameter tolerances are m6. Also known as parallel pins. This category may be available in the new MBA online store at Pins - Dowel - Standard - 316 Stainless - Rounded Both Ends.

Related Information:


Slides - Dovetail
Slides - Dovetail

Also see combined categories:
All Linear Slides

Used for work feeders for production milling, positioning fixutres, work holding devices, checking fixtures, shuttle devices, assembly equipment, etc.

Tapered gibs are adjusted with a single screw that moves the gib on the taper. This type remains parallel and wears less as it occurs over the entire surface. Made of continuous cast GS 40,000 PSI pearlitic grey iron. Able to be milled, drilled, tapped, etc. This category may be available in the new MBA online store at Slides - Dovetail.


Pins - Dowel - Standard - 316 Stainless - Chamfered End
Pins - Dowel - Standard - 316 Stainless - Chamfered End

Also see combined categories:
All Dowel Pins

Precision Dowel Pins - 316 Grade - Based on DIN6325, ISO2338, ISO 8734

Note! Type 2 pins may be supplied in lieu of type 1 pins. Also known as parallel pins. This category may be available in the new MBA online store at Pins - Dowel - Standard - 316 Stainless - Chamfered End.

Related Information:


Balls - Ceramic - Ruby - Synthetic
Balls - Ceramic - Ruby - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.

Related Information:


Balls - Ceramic - Sapphire - Synthetic
Balls - Ceramic - Sapphire - Synthetic

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).

Related Information:


Balls - Ceramic - Silicon Nitride
Balls - Ceramic - Silicon Nitride

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Outstanding wear resistance. Good thermal and chemical resistance.

High hardness. Grades shown are AFBMA / ISO3290-1. High strength over a wide temperature range. High fracture toughness. Outstanding wear resistance. Good thermal and chemical resistance.

Related Information:


Balls - Ceramic - Zirconia
Balls - Ceramic - Zirconia

Also see combined categories:
All Ceramic Balls
All Non Metallic Balls

Outstanding wear resistance. Excellent thermal and chemical resistance.

Grades shown are AFBMA / ISO3290-1. This category may be available in the new MBA online store at Balls - Ceramic - Zirconia.

Related Information:


Balls - Chrome Steel
Balls - Chrome Steel

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 60-70.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833. This category may be available in the new MBA online store at Balls - Chrome Steel.

Related Information:


Balls - Phosphor Bronze
Balls - Phosphor Bronze

Also see combined categories:
All Metallic Balls

Specific Gravity 8.4

Grades shown are AFBMA / ISO3290-1. This category may be available in the new MBA online store at Balls - Phosphor Bronze.

Related Information:


Balls - Stainless Steel - 304 Grade
Balls - Stainless Steel - 304 Grade

Also see combined categories:
All Metallic Balls

A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 oC. This category may be available in the new MBA online store at Balls - Stainless Steel - 304 Grade.

Related Information:


Balls - Stainless Steel - 316 Grade
Balls - Stainless Steel - 316 Grade

Also see combined categories:
All Metallic Balls

A4 Grade. Very low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 oC. This category may be available in the new MBA online store at Balls - Stainless Steel - 316 Grade.

Related Information:


Balls - Stainless Steel - 316L Grade
Balls - Stainless Steel - 316L Grade

Also see combined categories:
All Metallic Balls

Easier to machine than standard 316 grade.

316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. This category may be available in the new MBA online store at Balls - Stainless Steel - 316L Grade.

Related Information:


Balls - Stainless Steel - 400 Grade
Balls - Stainless Steel - 400 Grade

Also see combined categories:
All Metallic Balls

Hardness: Rockwell C: 55-60. Includes 420 and 440C grades

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. AISI440C Stainless Steel. This category may be available in the new MBA online store at Balls - Stainless Steel - 400 Grade.

Related Information:


Balls - Steel - Bored
Balls - Steel - Bored

Also see combined categories:
All Metallic Balls - Bored

Bored steel balls as used in steel rod ends.

Hardness: 58-64 Rc. Material: SUJ-2. This category may be available in the new MBA online store at Balls - Steel - Bored.

Related Information:


Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI

Also see combined categories:
All Metallic Balls

Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent. This category may be available in the new MBA online store at Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI.

Related Information:


Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded
Balls - Titanium Alloy - Ti-Gr23 Ti-6Al4V-ELI - Threaded

Also see combined categories:
All Threaded Metallic Balls

Implant Grade can be used for Jewellery and Body Piercing. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent.

Precision Grade: 200. Grades shown are AFBMA / ISO3290-1. Plain. Composition Percentage: Al 5.5-6.5, V 3.5-4.5, N 0.03, C 0.08, H 0.013, Fe 0.25, O 0.13, Ti Balance. Grade 23 6Al-4V is a high strength titanium alloy. Tensile Strength 84.5kgf / mm2. Yield Strength 77.5kgf / mm2. Elongation 10 Percent. Threaded either 1-72 UNF or M1.2.

Related Information:


Balls - Tungsten Carbide
Balls - Tungsten Carbide

Also see combined categories:
All Metallic Balls

Extreme hardness and wear resistance.

Tolerances available on request. Grades shown are AFBMA / ISO3290-1. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.

Related Information:


Balls - Plastic - Acetal
Balls - Plastic - Acetal

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.

Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Standard Opaque White. Specific Gravity: 1.4.

Related Information:


Balls - Plastic - Acrylic
Balls - Plastic - Acrylic

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Resistance to weather and sunlight. Good abrasion resistance.

Diametrical tolerances typically + / - 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.

Related Information:


Balls - Plastic - Bored
Balls - Plastic - Bored

Also see combined categories:
All Plastic Balls - Bored

Bored acetal balls as used in plastic rod ends.

Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight. This category may be available in the new MBA online store at Balls - Plastic - Bored.

Related Information:


Balls - Plastic - Nylon
Balls - Plastic - Nylon

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Resists alkalies, weak acids and most organic solvents.

Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.

Related Information:


Balls - Plastic - Polypropylene
Balls - Plastic - Polypropylene

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Excellent for liquid level float applications.

Tolerance and sphericity: up to and including 25.4mm diameter = + / -0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.

Related Information:


Balls - Plastic - PTFE
Balls - Plastic -  PTFE

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

No water absorption. Temperatures up to 288 Deg C.

Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 oC. Unpolished. Specific Gravity: 2.3.

Related Information:


Balls - Plastic - PVC
Balls - Plastic -  PVC

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

Polyvinyl chloride. PVC is a chemically stable material, which shows little change in molecular structure, and also exhibits little change in its mechanical strength.

Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. It is easily worked or machined and has good chemical and biological resistance. It is relatively hard and can be polished to a shine. Polyvinyl chloride is a widely used and inexpensive thermoplastic polymer. Heat Deflection Temperature 176 F / 80 C. Rockwell Hardness 115. Zero water absorption in 24 hours.

Related Information:


Balls - Plastic - Torlon
Balls - Plastic - Torlon

Also see combined categories:
All Plastic Balls
All Non Metallic Balls

TorlonTM 4301 Bearing Grade Balls. Grade 1.

Polyamide-imide (TorlonTM< / sup>) Balls. Rockwell Hardness (Method A): E86 or M109-119. Specific Gravity: 1.38. Colour: Brown Opaque. This category may be available in the new MBA online store at Balls - Plastic - Torlon.

Related Information:


Balls - Rubber - Santoprene 40D
Balls - Rubber - Santoprene 40D

Also see combined categories:
All Rubber Balls
All Non Metallic Balls

A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.

It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .95 g/cc. Hardness, Shore 40D. Tensile Strength 3000 psi. Melting Point 410 F. Rohs Compliant. Not FDA compliant. This grade is slightly harder than the 87A grade. Colour usually red but some sizes are beige.

Related Information:


Balls - Rubber - Santoprene 87A
Balls - Rubber - Santoprene 87A

Also see combined categories:
All Rubber Balls
All Non Metallic Balls

A high performance thermoplastic created by cross linking EPDM rubber with Polypropylene. As an elastomer plastic it is flexible, light weight, and has very good abrasion resistance. It also has good resistance to many acids, bases and aqueous solutions.

It holds up well in both extreme hot and cold environments which can make it preferred over rubber. Common uses include; grips, knobs, handles, gaskets, and ball check valves. Specific Gravity .96 g/cc. Hardness, Shore 87A. Tensile Strength 2550 psi. Melting Point 400 F. Rohs Compliant and FDA compliant. This grade is slightly softer than the 40D grade. Colour Beige.

Related Information:


Ball Transfer Units - Base Mount - Heavy Duty - Steel
Ball Transfer Units - Base Mount  - Heavy Duty - Steel

Also see combined categories:
All Base Mount Ball Transfers

Single ball bearings units for conveyor systems

This category may be available in the new MBA online store at Ball Transfer Units - Base Mount - Heavy Duty - Steel.


Ball Transfer Units - Dismantlable - Heavy Duty - Steel
Ball Transfer Units - Dismantlable  - Heavy Duty - Steel

Also see combined categories:
All Push Fit Ball Transfers

Single ball bearings units for conveyor systems

This category may be available in the new MBA online store at Ball Transfer Units - Dismantlable - Heavy Duty - Steel.


Ball Transfer Units - Flange Mount - Heavy Duty - Pressed Steel
Ball Transfer Units - Flange Mount - Heavy Duty - Pressed Steel

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems

This category may be available in the new MBA online store at Ball Transfer Units - Flange Mount - Heavy Duty - Pressed Steel.


Ball Transfer Units - Flange Mount - Heavy Duty - Stainless Steel
Ball Transfer Units - Flange Mount - Heavy Duty - Stainless Steel

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems



Ball Transfer Units - Flange Mount - Heavy Duty - Zinc Plated
Ball Transfer Units - Flange Mount - Heavy Duty - Zinc Plated

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems

This category may be available in the new MBA online store at Ball Transfer Units - Flange Mount - Heavy Duty - Zinc Plated.


Ball Transfer Units - Flange Mount - Standard - Stainless - Deep
Ball Transfer Units - Flange Mount - Standard - Stainless - Deep

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems

This category may be available in the new MBA online store at Ball Transfer Units - Flange Mount - Standard - Stainless - Deep.


Ball Transfer Units - Flange Mount - Standard - Stainless - Slim
Ball Transfer Units - Flange Mount - Standard - Stainless - Slim

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems

This category may be available in the new MBA online store at Ball Transfer Units - Flange Mount - Standard - Stainless - Slim.


Ball Transfer Units - Flange Mount - Standard - Steel - Slim
Ball Transfer Units - Flange Mount - Standard - Steel - Slim

Also see combined categories:
All Flange Mount Ball Transfers

Single ball bearings units for conveyor systems

This category may be available in the new MBA online store at Ball Transfer Units - Flange Mount - Standard - Steel - Slim.


Ball Transfer Units - Screw Stem - Brass and Aluminium
Ball Transfer Units - Screw Stem - Brass and Aluminium

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Brass and Aluminium.


Ball Transfer Units - Screw Stem - Stainless - Precision
Ball Transfer Units - Screw Stem - Stainless - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Stainless - Precision.


Ball Transfer Units - Screw Stem - Steel - Precision
Ball Transfer Units - Screw Stem - Steel - Precision

Also see combined categories:
All Screw Fit Ball Transfers

Single ball bearings units for conveyor systems

Applications include measuring equipment and light weight coil handlers. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms. This category may be available in the new MBA online store at Ball Transfer Units - Screw Stem - Steel - Precision.


Ball Transfer Units - Spring Loaded - Flanged - Zinc Plated
Ball Transfer Units - Spring Loaded - Flanged - Zinc Plated


Single ball bearings units for conveyor systems

Case: Zinc plated Mild Steel. Ball: Carbon Steel 60-66 HRC. Applications: - Guillotines - Presses - Moulding machines - Base of machines for easy handling - Press brakes - Shock loading. This category may be available in the new MBA online store at Ball Transfer Units - Spring Loaded - Flanged - Zinc Plated.





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138615 products in 2015 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138615 products in 2015 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.