Small Parts & Bearings - an MBA company

Attachments Wire Rope Clips Carbon Steel Categories


Cable


Attachments - Wire Rope Clips - Carbon Steel
Attachments - Wire Rope Clips - Carbon Steel

Also see combined categories:
All Wire Rope Clips

Hot galvanised carbon steel

Furnished with hex nuts. Meet USA Fed. Spec. FF-C-450c, Type I, Class 1. This category may be available in the new MBA online store at Attachments - Wire Rope Clips - Carbon Steel.


Attachments - Wire Rope Clips - Stainless Steel
Attachments - Wire Rope Clips - Stainless Steel

Also see combined categories:
All Wire Rope Clips

304 Stainless Steel

Furnished with hex nuts. Meet USA Fed. Spec. FF-C-450c, Type I, Class 1. This category may be available in the new MBA online store at Attachments - Wire Rope Clips - Stainless Steel.


Cable Attachments - Thimbles - Steel
Cable Attachments - Thimbles - Steel


Hot galvanised carbon steel. Use with synchromesh or standard miniature cable

Meets USA Fed. Spec. FF-T-276b for Type III thimbles. This category may be available in the new MBA online store at Cable Attachments - Thimbles - Steel.

Related Information:


Cable Attachments - Thimbles - Stainless Steel
Cable Attachments - Thimbles - Stainless Steel


316 Stainless Steel. Use with synchromesh cable or standard miniature cable. Use with synchromesh or standard miniature cable

Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends. This category may be available in the new MBA online store at Cable Attachments - Thimbles - Stainless Steel.

Related Information:


Push In Retaining Rings - Carbon Steel
Push In Retaining Rings - Carbon Steel


Thrust load shown is calculated for ideal conditions with mild steel bore. This category may be available in the new MBA online store at Push In Retaining Rings - Carbon Steel.


Push On Retaining Rings - Carbon Steel
Push On Retaining Rings - Carbon Steel

Also see combined categories:
All Push On Rings

M1465 / DTX / Seeger ZA and KS.

Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested. This category may be available in the new MBA online store at Push On Retaining Rings - Carbon Steel.


Snap Rings - External - Basic - Carbon Steel
Snap Rings - External - Basic - Carbon Steel

Also see combined categories:
All External Snaprings

Includes series M3200 / SP / ESP / M2400 / SW snaprings. Similar to a circlip without the lugs.

Carbon sping steel. Used on the outside diameter of a bearing, shaft or similar equipment. This category may be available in the new MBA online store at Snap Rings - External - Basic - Carbon Steel.


Snap Rings - Internal - Basic - Carbon Steel
Snap Rings - Internal - Basic - Carbon Steel

Also see combined categories:
All Internal Snaprings

M2300 / SB / ESB Snaprings. Like an internal circlip without the lugs.

Applications include gear systems, securing needle bearings and to act as spacers. Used on the inside bore diameter of a housing or similar. This category may be available in the new MBA online store at Snap Rings - Internal - Basic - Carbon Steel.


Pins - Wire Lock Lynch - Double Wire - Round - Carbon Steel
Pins - Wire Lock Lynch - Double Wire - Round - Carbon Steel

Also see combined categories:
All Wire Lock Lynch Pins

Also known as snapper pins

This category may be available in the new MBA online store at Pins - Wire Lock Lynch - Double Wire - Round - Carbon Steel.

Related Information:


Pins - Wire Lock Lynch - Double Wire - Square - Carbon Steel
Pins - Wire Lock Lynch - Double Wire - Square - Carbon Steel

Also see combined categories:
All Wire Lock Lynch Pins

Also known as snapper pins

This category may be available in the new MBA online store at Pins - Wire Lock Lynch - Double Wire - Square - Carbon Steel.

Related Information:


Pins - Wire Lock Lynch - Single Wire - Round - Carbon Steel
Pins - Wire Lock Lynch - Single Wire - Round - Carbon Steel

Also see combined categories:
All Wire Lock Lynch Pins

Also known as snapper pins

This category may be available in the new MBA online store at Pins - Wire Lock Lynch - Single Wire - Round - Carbon Steel.

Related Information:


Pins - Wire Lock Lynch - Single Wire - Square - Carbon Steel
Pins - Wire Lock Lynch - Single Wire - Square - Carbon Steel

Also see combined categories:
All Wire Lock Lynch Pins

Also known as snapper pins

This category may be available in the new MBA online store at Pins - Wire Lock Lynch - Single Wire - Square - Carbon Steel.

Related Information:


Pins - Wire Lock Lynch - Single Wire - Trapezoid - Carbon Steel
Pins - Wire Lock Lynch - Single Wire - Trapezoid - Carbon Steel

Also see combined categories:
All Wire Lock Lynch Pins

Also known as snapper pins

This category may be available in the new MBA online store at Pins - Wire Lock Lynch - Single Wire - Trapezoid - Carbon Steel.

Related Information:


Gears - Pinion Wire - 32 Diametrical Pitch
Gears - Pinion Wire - 32 Diametrical Pitch

Also see combined categories:
All Imperial Pinion Wire

Brass and carbon steel.

Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gears - Pinion Wire - 32 Diametrical Pitch.


Cable Attachments - Eyes
Cable Attachments - Eyes

Also see combined categories:
All Synchromesh Attachments

Use with synchromesh or standard miniature cable

Recommended dimensions after crimping:. 1.05 Cable - A=2.59. 2.06 Cable - A=2.64. 2.60 Cable - A=2.72. 3.40 Cable - A=2.80 (3.40 Cable must have outer helical wire removed prior to crimping).

Related Information:


E-Clips - Basic - Carbon Steel
E-Clips - Basic - Carbon Steel

Also see combined categories:
All E-Clips

Basic imperial and metric e-clips DIN6799 and N1500. Carbon spring steel including zinc plated and plain.

Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip. Includes plain and zinc plated. This category may be available in the new MBA online store at E-Clips - Basic - Carbon Steel.

Related Information:


Circlips - External - Standard - Carbon Steel
Circlips - External - Standard - Carbon Steel

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).

Plain carbon steel. This category may be available in the new MBA online store at Circlips - External - Standard - Carbon Steel.

Related Information:


Circlips - Internal - Standard - Carbon Steel
Circlips - Internal - Standard - Carbon Steel

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Plain carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Carbon Steel.

Related Information:


R Clips - Double Coil - Steel
R Clips - Double Coil - Steel

Also see combined categories:
All R Clips

Also known as internal hitch pins, bridge pins or humpback pins

Material: Spring Wire. This category may be available in the new MBA online store at R Clips - Double Coil - Steel.


R Clips - Single Coil - Steel
R Clips - Single Coil - Steel

Also see combined categories:
All R Clips

Also known as internal hitch pins, bridge pins or humpback pins

Material: Spring Wire. This category may be available in the new MBA online store at R Clips - Single Coil - Steel.


Pins - Clevis - Pin Locking - Low Carbon Steel
Pins - Clevis - Pin Locking - Low Carbon Steel

Also see combined categories:
All Clevis Pins

Match with a suitable R-Clip or Spilt Pin - pin size shown in listings

In addition to retaining parts on a shaft or axle, clevis pins can also be used as light duty axles, spring holders or even fishing line weights. Made from low carbon steel. This category may be available in the new MBA online store at Pins - Clevis - Pin Locking - Low Carbon Steel.

Related Information:


Shafting - Carbon Steel - Keyed
Shafting - Carbon Steel - Keyed

Also see combined categories:
All Shafting
All Steel Shafting

Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.

Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.


Washers - Flat - Carbon Spring Steel - Precision Shim
Washers - Flat - Carbon Spring Steel - Precision Shim

Also see combined categories:
All Precision Shim Washers
All Flat Washers and Spacers - Metallic

Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.

C1010 steel types best suited to arbor shimming. This category may be available in the new MBA online store at Washers - Flat - Carbon Spring Steel - Precision Shim.

Related Information:


Pins - Clik - Carbon Steel
Pins - Clik - Carbon Steel

Also see combined categories:
All Clik Lynch Pins

Self locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Also known as a lynch pin.

Pin is made from carbon steel and heat treated to RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated. This category may be available in the new MBA online store at Pins - Clik - Carbon Steel.

Related Information:


Pins - Roll - Carbon Steel
Pins - Roll - Carbon Steel

Also see combined categories:
All Roll Pins

Plain carbon spring steel DIN1481/ISO8752.

Also known as sel-lok and bissell pins. This category may be available in the new MBA online store at Pins - Roll - Carbon Steel.

Related Information:


Hexagonal Bar - Carbon Steel
Hexagonal Bar - Carbon Steel

Also see combined categories:
All Metal Bar - Hexagonal

Saw Cut Ends. Small A/F sizes may not be perfectly straight. This category may be available in the new MBA online store at Hexagonal Bar - Carbon Steel.


Keys - Machine - Carbon Steel
Keys - Machine - Carbon Steel

Also see combined categories:
All Machine Keys

Form A has rounded ends. Form B has square ends. Form AB has one end rounded and one end square. DIN6885

This category may be available in the new MBA online store at Keys - Machine - Carbon Steel.

Related Information:


Tools - Dies - Carbon Steel
Tools - Dies - Carbon Steel

Also see combined categories:
All Dies
All Tools

Tungsten Chrome Alloy - Carbon Steel Button dies and die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.

This category may be available in the new MBA online store at Tools - Dies - Carbon Steel.


Tools - Taps - Carbon Steel - Hand - Standard
Tools - Taps - Carbon Steel - Hand - Standard

Also see combined categories:
All Taps
All Tools

Carbon Steel Straight Flute Taps. Starting from M1 and 0-90 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.

Carbon steel hand taps. Carbon Steel (CS) Hand taps. This category may be available in the new MBA online store at Tools - Taps - Carbon Steel - Hand - Standard.


Pins - Dowel - Extractable - Carbon Steel
Pins - Dowel - Extractable - Carbon Steel

Also see combined categories:
All Dowel Pins

Hardened and Ground Steel 100 Cr6. Din 7979.

Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin to overcome the problem of pressure build up by trapped air. Hardness 55-62 HRC, HV550-650. Extractable pins may or may not have a flat to vent pressure when pulling. Also known as parallel pins.

Related Information:


Pins - Taper Metric - Carbon Steel
Pins - Taper Metric - Carbon Steel

Also see combined categories:
All Metric Taper Pins

Metric Sizes Tapered 1:50. DIN 1 - A - Ground Ra 0.8um

Metric Sizes to DIN 1. This category may be available in the new MBA online store at Pins - Taper Metric - Carbon Steel.

Related Information:


Sleeves - Hex Hole - Carbon Steel
Sleeves - Hex Hole - Carbon Steel

Also see combined categories:
All Hex Hole Sleeves

Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.

This category may be available in the new MBA online store at Sleeves - Hex Hole - Carbon Steel.


Washers - Disc Spring - Carbon Steel
Washers - Disc Spring - Carbon Steel

Also see combined categories:
All Disc Springs

Includes disc springs to DIN 2093.

Manufactured under strict quality control to conform to DIN 2093. This category may be available in the new MBA online store at Washers - Disc Spring - Carbon Steel.


Washers - Spring - Curved - Carbon Steel
Washers - Spring - Curved - Carbon Steel

Also see combined categories:
All Wave Washers

Wave Washers - All Materials.

ID and OD are long axis dimensions. This category may be available in the new MBA online store at Washers - Spring - Curved - Carbon Steel.


Keysteel Lengths - Rectangular - Carbon Steel
Keysteel Lengths - Rectangular - Carbon Steel

Also see combined categories:
All Keysteel Lengths

Plain carbon steel key steel. Rectangular steel bar that can be used for keysteel or for small construction projects.

Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled. This category may be available in the new MBA online store at Keysteel Lengths - Rectangular - Carbon Steel.

Related Information:


Keysteel Lengths - Square - Carbon Steel
Keysteel Lengths - Square - Carbon Steel

Also see combined categories:
All Keysteel Lengths

Plain carbon steel key steel. Square steel bar that can be used for keysteel or for small construction projects.

Use oversized for replacing keys where the keyway may be slightly worn - standard aftermarket keysteel. Use undersized for manufacturing and new applications where the keyway tolerances can be controlled. This category may be available in the new MBA online store at Keysteel Lengths - Square - Carbon Steel.

Related Information:


Hooks - S - Steel
Hooks - S - Steel

Also see combined categories:
All S Hooks

Low carbon cold drawn steel with zinc plated finish

Any deviations such as angular lifts, shock loads, modifications will result in drastically reduced maximum loads. This category may be available in the new MBA online store at Hooks - S - Steel.


Rod Ends - Steel - Bronze Lined Female
Rod Ends - Steel - Bronze Lined Female

Also see combined categories:
All Female Rod Ends
All Steel Female Rod Ends

Imperial and Metric / Carbon Steel. Also known as Heim Joints

Dimensions not shown are available on request. This category may be available in the new MBA online store at Rod Ends - Steel - Bronze Lined Female.


Rod Ends - Steel - Bronze Lined Male
Rod Ends - Steel - Bronze Lined Male

Also see combined categories:
All Male Rod Ends
All Steel Male Rod Ends

Imperial and Metric / Carbon Steel. Also known as Heim Joints

Dimensions not shown are available on request. This category may be available in the new MBA online store at Rod Ends - Steel - Bronze Lined Male.


Bolts - Eye Blank Shank - Carbon Steel
Bolts - Eye Blank Shank - Carbon Steel

Also see combined categories:
All Eye Bolts

Forged self coloured carbon steel. No threads. No capacity rating as this will depend on your modifications.

Forged self coloured carbon steel. Should not be used for angular lifts greater than 45o. Safety swivel hoist rings are recommended for such applications. This category may be available in the new MBA online store at Bolts - Eye Blank Shank - Carbon Steel.


Pins - Taper Imperial - Miniature - Carbon Steel
Pins - Taper Imperial - Miniature - Carbon Steel

Also see combined categories:
All Imperial Taper Pins

Imperial Sizes Tapered 1:48 (1/4 in. per foot). Miniature sizes.

This category may be available in the new MBA online store at Pins - Taper Imperial - Miniature - Carbon Steel.

Related Information:


Pins - Taper Imperial - Standard - Carbon Steel
Pins - Taper Imperial - Standard - Carbon Steel

Also see combined categories:
All Imperial Taper Pins

Imperial Sizes Tapered 1:48 (1/4 in. per foot). Standard sizes numbers 0 to 14.

This category may be available in the new MBA online store at Pins - Taper Imperial - Standard - Carbon Steel.

Related Information:


Screws - Shoulder - Socket Head - Carbon Steel
Screws - Shoulder - Socket Head - Carbon Steel

Also see combined categories:
All Shoulder Screws

Also known as stripper bolts. This category may be available in the new MBA online store at Screws - Shoulder - Socket Head - Carbon Steel.


Sleeves - Square Hole - Plain - Carbon Steel
Sleeves - Square Hole - Plain - Carbon Steel

Also see combined categories:
All Square Hole Sleeves

Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.

This category may be available in the new MBA online store at Sleeves - Square Hole - Plain - Carbon Steel.


Sleeves - Square Hole - Threaded - Carbon Steel
Sleeves - Square Hole - Threaded - Carbon Steel

Also see combined categories:
All Square Hole Sleeves

Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through and threaded internally at one end.

This category may be available in the new MBA online store at Sleeves - Square Hole - Threaded - Carbon Steel.


Washers - Spring - Wave Type - Carbon Steel
Washers - Spring - Wave Type - Carbon Steel

Also see combined categories:
All Wave Washers

Wave Washers - also called crinkle wave. Includes 2 and 3 wave types. This category includes EPL type bearing pre-load washers.

This category may be available in the new MBA online store at Washers - Spring - Wave Type - Carbon Steel.


Feeler Gauge Stock - C1095 Carbon Steel
Feeler Gauge Stock - C1095 Carbon Steel


Used for close spacing and extremely tight tolerance situation.

Rc48-62 hardness. High carbon steel. Short flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 inches and can be easily cut to length. 12.7mm wide.


Shafting - Ground - Precision - High Carbon Steel
Shafting - Ground - Precision - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - High Carbon Steel.

Related Information:


Washers - Flat - Hardened Steel
Washers - Flat - Hardened Steel

Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic

Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.

This category may be available in the new MBA online store at Washers - Flat - Hardened Steel.

Related Information:


Studs - Full Thread - Steel
Studs - Full Thread - Steel

Also see combined categories:
All Studs

Low carbon steel allthread threaded bar

Short lengths of threaded low carbon steel bar. This category may be available in the new MBA online store at Studs - Full Thread - Steel.





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 153564 products in 2094 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 153564 products in 2094 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.