Cable
Use with synchromesh or standard miniature cable. Use a swaging tool to compress the stop sleeve over the end of the cable.
Related Information:
Use with synchromesh or standard miniature cable
Related Information:
Use with synchromesh or standard miniature cable
Recommended dimensions after crimping:. 1.05 Cable - A=2.59. 2.06 Cable - A=2.64. 2.60 Cable - A=2.72. 3.40 Cable - A=2.80 (3.40 Cable must have outer helical wire removed prior to crimping).
Related Information:
Hot galvanised carbon steel. Use with synchromesh or standard miniature cable
Related Information:
316 Stainless Steel. Use with synchromesh cable or standard miniature cable. Use with synchromesh or standard miniature cable
Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends. This category may be available in the new MBA online store at
Attachments - Cable - Thimbles - Stainless Steel.
Related Information:
Use with synchromesh or standard miniature cable
F and L dimensions are obtained after swaging. Before swaging the fitting is round. This category may be available in the new MBA online store at
Attachments - Cable - Threaded Plugs.
Related Information:
Hot galvanised carbon steel
304 Stainless Steel
Lever knobs with moulded female threads, ideal for direct attachment to operating levers. Plastic (high grade gloss black phenolic) with Steel insert. Temperature Range: -30
oC to +140
oC. All knobs are fitted with a brass female insert. This category may be available in the new MBA online store at
Knobs - Lever - Threaded Bore.
Related Information:
Lever knobs with moulded female threads, ideal for direct attachment to operating levers. Plastic (high grade gloss black phenolic) with Steel insert. Temperature Range: -30
oC to +140
oC. All knobs are fitted with a brass female insert. This category may be available in the new MBA online store at
Knobs - Lever - Through Bore.
Related Information:
Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.
Pre hardened to Rockwell 23-30C. Carefully turned to provide 0.076mm (0.003in) concentricity ID to OD. Round OD with with a uniform hex hole broached from one end to the other.
Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.
Pre hardened to Rockwell 23-30C. Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through.
Square and concentric to 0.076mm (0.003in). Round OD with with a uniform square hole all the way through and threaded internally at one end.
Simple effective way to lock components onto shafts.
416 Stainless Steel. Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened. This category may be available in the new MBA online store at
Shaftloc-tm Sleeves - Single Ended.
Related Information:
Match with hubs from hubs category
Related Information:
Match with hubs from the hubs category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
Low cost protection for threaded and cylindrical parts
Elastic snug tight fit protective sleeve fits over straight, tapered or contoured parts. Made from polyethylene. Thickness of web approx 1.8mm. Sold per foot (300mm). Maximum contunuous roll is 100 feet (30 mtrs).
Hardened sleeves for needle roller bearings.
Related Information:
Match with sleeves from sleeves category
Related Information:
Match with sleeves from the sleeves category
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1o Angular Displacement. Free axial movement. 19.55 to 88 Nm. 8500 to 14000 rpm. High torque / low inertia.
Related Information:
Low cost alternative for making your own wheels, castors, rollers, sheaves etc. Urethane rod with dual hardness. Harder inner sleeve with softer outside for use as a roller.
Blue outer tyre 90A Durometer bonded to a hard brown 75D Durometer inner sleeve. This results in a hard anti friction bearing surface inside with a soft tyre outside. The roller can be cut and machined to suit your purposes. Testing for your application is recommended. This category may be available in the new MBA online store at
Rollers - Urethane - Lengths.
Related Information:
Unthreaded
Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.
Unthreaded. Plastic body and ball.
Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.
Timing Pulleys to suit HTD 3.000mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Moulded single or double flange. No hub.
Suitable for use with shaftloc sleeves.
Related Information:
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is hardened and ground smooth. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is hardened and ground smooth. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Related Information:
Elastomer bumpers provide excellent resistance to chemicals and humidity. 20 times greater durability than urethane.
10 greater durability than rubber and 500 times greater than steel coiled springs. Also see Mounts - Buffers. Maintains excellent resilience at extreme temperatures and remains flexible with no material degradation between -62
oC and +148 Deg C (-80 Deg F and +300 Deg F). Mounting screws not included. This category may be available in the new MBA online store at
Bumpers - Elastomer - Radial - Low Energy - Longer - Soft Stop.
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs. This category may be available in the new MBA online store at
Collars - Shaft - Gripfast - ABS Plastic.
Related Information:
Rails, rollers and end stops sold separately. Please choose your components from the listing.
Easy to use system is usually mounted on a vertical surface as a low cost linear motion solution. Hardened crown roller allows for self-alignment with good strength and long life. Rails are unistrut typeand are black powder coated. End stops prevent over travel and come with a mounting bolt. End stops are not designed to support loads. Maximum bearing load is 130 kg. Maximum bearing speed is 45 mtrs per minute. This category may be available in the new MBA online store at
Linear Track System - Crowned Roller.
Thermoplastic housed units offer a more favourable economic choice. Hard chrome inserts offer an intermediate level of corrosion resistance.
Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel.
Thermoplastic housed units offer a more favourable economic choice. Hard chrome inserts offer an intermediate level of corrosion resistance.
Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel.
Individual Inserts for use with the Klik Thread Setter Tool
These threaded inserts can be used in blind or through hole applications. Can be used in almost any material over 2.38mm thick. As the insert is installed the threaded section is completely swaged into the sleeve portion of the hole, permitting them to be used with grade 8 screws. The installation hole size is determined by the density of the parent material. Can be pressed or otherwise compressed manually with a hammer for quick installation jobs in sheet material. Tools are available for assembly in blind holes or production assembly. Email us for a price on tools.
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
Thermoplastic housed units offer a more favourable economic choice. Stainless steel bearings offer a high level of corrosion resistance and all metal parts are made from either 302, 304 or 440C stainless steel.
Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel. Food grade.
The BSR precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants. Note BSR1530SL and BSR2040SL can not be mounted from inside of track rail.
Thermoplastic housed units offer a more favourable economic choice. Stainless steel bearings offer a high level of corrosion resistance and all metal parts are made from either 302, 304 or 440C stainless steel.
Operating temperature minus 20 oC to +95 deg C. Thermoplastic hosuings are offwhite and are made from glass reinforced PBT resin. Favourable chemical resistance. Very resistant to moisture absorption. Excellent mechanical, thermal and electrical properties. All sleeves, bushings and grease fittings are 300 grade stainless steel. Food Grade.
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.
Higher load capacity than precision ball slide assemblies. High cycling rates. Tolerant of shock and overhanging loads.
Accuracy of 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm. Not as naturally cleaning as ball slides. A good choice for environments protected from dust, and when heavy loads are a consideration. Positive stops prevent over-travel. Rollers improve capacity 8-10 times that of balls. Alternately crossed rollers handle force in any direction. Lightweight aluminium carriage and base. Interchangeable with many types of ball slides. Four tapped carriage holes and two counter bored base holes simplify installation and component mounting. This category may be available in the new MBA online store at
Linear Slide Assemblies - Cross Roller.
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). This category may be available in the new MBA online store at
Slides - Drawer - Front Disconnect - Friction - 19mm Ext.
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide with a quick disconnect. This category may be available in the new MBA online store at
Slides - Drawer - Quick Disconnect - Medium Duty - Full Ext.
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.