Circlips
DIN984 / D2000 / Seeger JK. Retaining rings. Snap Rings (USA).
Internal tabs are concentrically positioned for a concealed assembly. Tabs act as spacers for securing machine components.
Related Information:
Clips
M1465 / DTX / Seeger ZA and KS.
Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested.
Circlips
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Plain carbon steel. Tolerances on request.
Related Information:
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. Tolerances on request.
Related Information:
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Zinc plated carbon steel. Tolerances on request.
Related Information:
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Retaining rings. Snap Rings (USA).
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.
Related Information:
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening
Fastener may be steel, brass or zinc plated. Natural Rubber isolator.
Related Information:
Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening
Related Information:
Neoprene 60 durometer black ground outside diameter drive rollers
Permanent Magnet.
Max. Allowable Radial Load: 100N (10mm from mounting surface). Max. Allowable Axial Load: 30N. Axial Play: 0.05 - 0.6mm. Allowable Temperature Range: -20oC to +60oC. Integral CD PM Motor - Brush type commutation - 12 segment commutator - RFI protection standard. Gear train with steel and high quality plastic gears - Terminal dimensions 4.8 x 0.8 - Weight: 1200g.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.
Operating Temperature -200o to 280o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating. Speed Limit in oil 4.5 metres surface speed per second.
Related Information:
Oil, acid, alkali and salt water resistant. Contains no lead. Particularly suited to food applications, flow meters and pumps in pharmaceutical applications, printing machines chemical engineering and seawater applications.
Operating Temperature -200o to 280o Celsuis. PTFE with oilfibre 0.01 to around 0.03mm. Porous bronze 0.2 to around 0.3mm. Stainless steel backing 0.7 to around 2.3mm. 140 N/mm2 dynamic load rating. 250 N/mm2 static. 60 N/mm2 Oscillating. Speed Limit in oil 4.5 metres surface speed per second.
Related Information:
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with soft plastics, hard and soft wood, particle board.
Related Information:
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
Hardness: Rockwell C: 60-70.
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.
Related Information:
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
Related Information:
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.
Related Information:
Use with Utilitrak PW Crowned Carriages. 6063-T6 aluminium alloy. Economical choice for light duty applications.
Related Information:
Compliance with UL 1950 and EN 60950 codes for access areas. Ratchet mechanism allows screw to be tightened down by hand, but a tool is needed to loosen.Fully retractable captive to the panel and spring ejected.
Press in style. Bright chromate zinc plated, case hardened steel with aluminium knob and stainless steel spring. Knobs available either slotted or no.2 phillips.
Use with Utilitrak PW Dual Vee Carriages. 6063-T6 aluminium alloy. Economical choice for light duty applications.
Related Information:
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
High Precision Corrosion Resistant Miniature Linear Bearings.
High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.
Related Information:
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. For rotating and linear motion.
Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. For rotating and linear motion.
CDA 360 Free Machining Brass
Polished balls are fully finished and suitable for decorative and display purposes.
Related Information:
Using Frelon Gold plain bearing technology. Rail and carriage are made from 6063-T6 aluminium and come as a set.
Rails are ceramic coated to resist corrosion and repel weld spatter and contaminants. Smooth running. Dampens vibration. Guide has slots for T nuts or bolts. Two component system allows for easier installation than traditional rail systems.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
Related Information:
Flanges for Acme leadscrew thread supernuts metric and imperial
MATERIAL - Aluminum 6062-T6. These flanges are screwed onto the outer thread of the red leadscrew nuts. This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved.
Related Information:
Imperial and metric DIN471 / N1400 / D1460. Retaining rings. Snap Rings (USA).
Related Information:
Single and double length
Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. Double length has two bearings mounted internally. For rotating and linear motion.
Single and double length
Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. Double length has two bearings mounted internally. For rotating and linear motion.
Single and double length
Bearing is Frelon Gold -tm- encased in a flanged housing made from 6061-T6 aluminium. Double length has two bearings mounted internally. For rotating and linear motion.
Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.
Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated.
Related Information:
Imperial and metric DIN471 / D1400 / N1400 / D1460. Retaining rings. Snap Rings (USA).
Plain carbon steel.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 131199
products in 2163 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.