A44ARS SEEGER
Cross Referenced Part Numbers
Seeger part number A44-ARSMatches our part number
Shaft Diameter (Ds): 44.00. Groove Dia. (Dg): 41.50. Clip Thickness (T): 1.75.
Part Link: CCE-04400-C
Online Price: 0.00
Stock: 38
Stock: 38
Category Matches
Circlips
Circlips - Internal - Tabbed
DIN984 / D2000 / Seeger JK. Retaining rings. Snap Rings (USA).
Internal tabs are concentrically positioned for a concealed assembly. Tabs act as spacers for securing machine components.
Related Information:
Clips
Push On Retaining Rings - Carbon Steel
M1465 / DTX / Seeger ZA and KS.
Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested.
Circlips
Circlips - External - Grooveless
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Retaining rings. Snap Rings (USA).
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.
Related Information:
Circlips - Internal - Standard - Carbon Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Plain carbon steel. Tolerances on request.
Related Information:
Circlips - Internal - Standard - Stainless Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. Tolerances on request.
Related Information:
Circlips - Internal - Standard - Zinc Plated
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Zinc plated carbon steel. Tolerances on request.
Related Information:
Couplings - Oldham - Hubs - Clamp Style
0.06 to 44 Nm. Max Speed: 3000 RPM.
Single hubs. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Related Information:
Couplings - Oldham - Disks for Clamp Style
0.06 to 44 Nm. Max Speed: 3000 RPM.
Disk inserts. This type of coupling is ideal for applications where it is difficult to move shafts to allow the coupling to be installed. The centre disk can be fitted after the hubs have been assembled and aligned.
Related Information:
Bearings - Ball - 440C Stainless
Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
Stainless steel radial ball bearings
Standard single row radial ball bearings. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
Bearings - Ball - Flanged - 440C Stainless
Stainless Steel Bearings with Flanges.
Single row radial ball bearings with flanges. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
Bearings - Ball - WIR - 440C Stainless
Stainless Steel Bearings with a Snap Ring on the OD
Single row radial ball bearings with extended inner ring (wide inner ring). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
Bearings - Ball - Angular Contact - 440C Stainless
Including miniature sizes down to 8mm from stock and even smaller available.
Single row angular contact ball bearings.
Related Information:
Bearings - Ball - Flanged - WIR - 440C Stainless
Stainless Steel Bearings with Flanges.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore.
Related Information:
Bearings - Ball - Angular Contact - Flanged - 440C Stainless
Single row angular contact ball bearings with flanges.
Related Information:
Shafting - Ground - Precision - Stainless 440C Grade Hardened
Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.
Related Information:
Balls - Checking - Stainless Steel
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.
Related Information:
Balls - Fixture - Stainless Steel
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.
Related Information:
Gearboxes - Right Angle - Model RA 0750-0750-0440 - 75.0 x 75.0 x 44.0mm
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
Related Information:
Bearings - Ball - High Precision - 440C Stainless
Also see combined categories:
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
All Radial Ball Bearings
All Basic Single Row Bearings Stainless and Chrome
Stainless Steel Bearings - Abec 5 and Abec 7.
Single row radial ball bearings. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
Bearings - Ball - Anti Corrosion - Special Stainless
Higher corrosion resistance than 440C stainless - HRC59 Hardness - Same or higher load than 440C
Ideal for applications with salt spray or chemicals in the pH range 3 to 12. ISC CASSTOP design with special TBN-6H stainless steel. Other sizes available on request.
Related Information:
Housings - Bearing - Pillow Block - Miniature
Spyraflo aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings. Double shielded bearings to minimise contamination.
Related Information:
Balls - Checking - Stainless Steel - With Tapped Shank
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft.
Related Information:
Bearings - Ball - Flanged - High Precision - 440C Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
Bearings - Ball - WIR - High Precision - 440C Stainless
Stainless Steel Bearings - Abec 5 and Abec 7.
Single row radial ball bearings with extended inner ring (wide inner ring). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
Bearings - Ball - Flanged - WIR - High Precision - 440C Stainless
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
Related Information:
Balls - Stainless Steel - 400 Grade
Hardness: Rockwell C: 55-60. Includes 420 and 440C grades
Tolerances available on request. Grades shown are AFBMA / ISO3290-1. AISI440C Stainless Steel.
Related Information:
Screws - Panel - Jack - Steel
Female 4-40 UNC thread in head allows for secure fixing of studs to a panel.
Each screw comes with two flat washers, 1one lock washer and one hex nut. Yellow chromate zinc finish.
Slides - Linear - Clean Room
Stainless Steel throughout (similar to 440C). Speed: 0.5 m/sec (30 m/min). Temperature: +100oC (Continuous), +140oC (Maximum). Life will be less than normal at +100oC and dimensions may change. Lateral Loading: Dynamic x 1.13 C - Static x 1.19 Co. Precision Linear Slide Unit is a compact linear motion rolling guide for limited stroke length.
Motors - DC 30.5X24.2X18.3 mm
MF-28 Series - 1.5 to 24 VDC - 4470 to 13430 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
Related Information:
Universal Joints - Single Joint - High Speed - Plain Bore - Stainless
303 Stainless Body with 440 Stainless Balls. Maximum operating angle 30 degrees (45 for hand operated applications). Zero backlash. Sealed lubrication. Light weight and low inertia. Not supplied with set screws or tapped holes.
Related Information:
Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing
Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.
Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.
Balls - Tooling - One Piece - Standard - Stainless Steel - Press Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
440C Stainless Steel heat treated to 55-58 RC.
Related Information:
Balls - Tooling - One Piece - Standard - Stainless Steel - Slip Fit
High quality tooling balls provide a precise reference point for critical machining operations. Available with slip fit or light press fit shank diameters.
440C Stainless Steel heat treated to 55-58 RC.
Related Information:
AR2000 Daiwa Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Housings - Bearing - 3 Bolt Offset - Thermoplastic with Stainless Bearing
Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.
Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.
Housings - Bearing - 4 Bolt Flange - Thermoplastic with Stainless Bearing
Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.
Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.
Pool Sweep Arneson Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
9072702 Long Arm Jentschman Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Housings - Bearing - Tapped Base Unit - Stainless
Full stainless steel bearing units are the best solution for hostile chemical washdown applications. All metal bearing insert components are a combination of 302, 304 and 440 stainless steel. Seals are silicone rubber. Grease is H-1 food grade.
Operating temperature minus 20 oC to +120 deg C. Solid 304 stainless housings have a machined base and extremely smooth surface finish, essential for demanding washdown installations. These housings do not experience flaking, cracking or discolouration and are virtually unaffected by scrapes. Bearings are removable. Food grade.
Turntable - Lockable
Heavy duty turntables are ideal for swivel displays, welding tables, industrial assemblies and many other applications.
Similar to lazy susans but heavy duty.
Related Information:
Bumpers - Radial - Tube
These bumpers are designed for applications involving shock and collision protection along a straight line.
Made from TecsPaks patented elastomer. Less than 40D hardness. Mounting bolt not included.
Springs - Urethane
Urethane springs are designed for use in applications where corrosion, vibration or magnetism prevent the use of conventional steel springs.
They replace steel coil springs in medium pressure applications involving space limitations, high blank holding pressure and adequate stripping. Durometer 95 shore A. Colour black. Tensile strength 5000 psi. Temperature range minus 40 to 80 oC.
Related Information:
Bearings - Acetal - Double Row - with 316 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.
Related Information:
Bearings - Acetal - Double Row - with Glass Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.
Related Information:
Bearings - Acetal - Single Row - with 302 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 302 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 oC to 100 oC Continuous.
Related Information:
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Dental Bearings
Dowel Pins
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 127040 products in 2365 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
