A37 SEEGER
Cross Referenced Part Numbers
Seeger part number A37-BLSMatches our part number
Shaft Diameter (Ds): 37.00. Clip Thickness (T): 1.75. Groove Dia. (Dg): 35.00.
Part Link: CCE-03700-C
Retail Price: 0.00 (Pack of 125
)
Lower price for quantities
Stock: Pre-Order (due 14 weeks) Due dates are estimates only
Lower price for quantities
Stock: Pre-Order (due 14 weeks) Due dates are estimates only
Seeger part number A37Matches our part number
Shaft Diameter (Ds): 37.00. Clip Thickness (T): 1.75. Groove Dia. (Dg): 35.00.
Part Link: CCE-03700-C
Retail Price: 0.00 (Pack of 125
)
Lower price for quantities
Stock: Pre-Order (due 14 weeks) Due dates are estimates only
Lower price for quantities
Stock: Pre-Order (due 14 weeks) Due dates are estimates only
Seeger part number A37X1.75Matches our part number
Shaft Diameter (Ds): 37.00. Clip Thickness (T): 1.75. Groove Dia. (Dg): 35.00.
Part Link: CCE-03700-C
Retail Price: 0.00 (Pack of 125
)
Lower price for quantities
Stock: Pre-Order (due 14 weeks) Due dates are estimates only
Lower price for quantities
Stock: Pre-Order (due 14 weeks) Due dates are estimates only
Category Matches
Circlips
Circlips - Internal - Tabbed
DIN984 / D2000 / Seeger JK. Retaining rings. Snap Rings (USA).
Internal tabs are concentrically positioned for a concealed assembly. Tabs act as spacers for securing machine components. This category may be available in the new MBA online store at Circlips - Internal - Tabbed.
Related Information:
Clips
Push On Retaining Rings - Carbon Steel
M1465 / DTX / Seeger ZA and KS.
Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested. This category may be available in the new MBA online store at Push On Retaining Rings - Carbon Steel.
Circlips
Circlips - Grooveless
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Retaining rings. Snap Rings (USA).
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring. This category may be available in the new MBA online store at Circlips - Grooveless.
Related Information:
Circlips - Internal - Standard - Carbon Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Plain carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Carbon Steel.
Related Information:
Circlips - Internal - Standard - Stainless Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Stainless Steel.
Related Information:
Circlips - Internal - Standard - Zinc Plated
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Zinc plated carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Zinc Plated.
Related Information:
Springs - Die - Imperial - Medium Heavy Duty - Chrome Silicon
Chrome silicon die springs are longer lasting than high carbon steel. Shot peened to reduce working stress and to improve the surface.
Colour coded red. Efficient operating range is 20 to 25 percent of the length. Maximum deflection is 37 percent of the length. This category may be available in the new MBA online store at Springs - Die - Imperial - Medium Heavy Duty - Chrome Silicon.
Related Information:
Springs - Die - Imperial - Medium-Heavy Duty
Vapor degassed high tensile strength chromium alloy steel. Spring ends are ground square. Designed for long life cycle with constant high end deflections and shot peened to increase fatigue life.
Colour coded red. Efficient operating range is 20 to 30 percent of the length. Maximum deflection is 37 percent of the length. This category may be available in the new MBA online store at Springs - Die - Imperial - Medium-Heavy Duty.
Related Information:
637B Mini Lux 3 BellaTorque Kavo Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Oil Seals - Fluoroelastomer Rubber
DIN 3760 - High Temperature and chemical resistance.
Operating Temp. Range: -20oC to +240oC. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Suitable for synthetic and hydraulic fluids, strong acids, steam, many chemicals and many alkalis. This category may be available in the new MBA online store at Oil Seals - Fluoroelastomer Rubber.
Oil Seals - Nitrile Rubber
DIN 3760 - General purpose grease and oil sealing. Note - metal cased and rubber cased seals may be interchanged at our discretion. If one or the other is specifically required please let us know when ordering.
Operating Temp. Range: -30oC to +90oC. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids. This category may be available in the new MBA online store at Oil Seals - Nitrile Rubber.
Bushes - Plastic Unflanged - Iglidur H370
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Belts - Inch Timing - 9.525mm Pitch L - 38.1mm Wide
Standard Series Timing Belts 9.525mm or 0.375 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Pitch (P) - 9.525mm (0.200 inch).
Related Information:
Belts - Inch Timing - 9.525mm Pitch L - 12.7mm Wide - Standard
Standard Series Timing Belts 9.525mm or 0.375 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Pitch (P) - 9.525mm (0.200 inch).
Related Information:
Belts - Inch Timing - 9.525mm Pitch L - 19.1mm Wide - Standard
Standard Series Timing Belts 9.525mm or 0.375 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Pitch (P) - 9.525mm (0.200 inch).
Related Information:
Belts - Inch Timing - 9.525mm Pitch L - 25.4mm Wide - Standard
Standard Series Timing Belts 9.525mm or 0.375 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Pitch (P) - 9.525mm (0.200 inch).
Related Information:
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153564 products in 2094 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
