Circlips
DIN984 / D2000 / Seeger JK. Retaining rings. Snap Rings (USA).
Internal tabs are concentrically positioned for a concealed assembly. Tabs act as spacers for securing machine components.
Related Information:
Clips
M1465 / DTX / Seeger ZA and KS.
Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested.
Circlips
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Retaining rings. Snap Rings (USA).
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.
Related Information:
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Plain carbon steel. Tolerances on request.
Related Information:
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. Tolerances on request.
Related Information:
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Zinc plated carbon steel. Tolerances on request.
Related Information:
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
CDA 360 Free Machining Brass
Polished balls are fully finished and suitable for decorative and display purposes.
Related Information:
Chrome finished zinc die-cast construction. 360o handle rotation. Comes with gasket. All locks are keyed alike. Keys included. May be used with rod kit for 2 point locking.
Related Information:
Gold zinc finished steel. Die cast construction. 5/16in. Square shank. 360o rotation. Blind mount. Padlockable.
Use with idler shafts and idler pulleys. Fixed base with adjustable arm through 360o.
Idler shaft and pulleys not included with tensioner.
Related Information:
Use with idler shafts and idler pulleys. Mounts on any free point of a fixed shaft allowing controlled tensioning around 360o.
Idler shaft and pulleys not included with tensioner.
Related Information:
Use with idler shafts and idler pulleys. Adjusting slot assists with precise adjustments.
Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360o controlled tensioning. Serrated teeth to prevent slippage once tightened.
Related Information:
Use with idler shafts and idler pulleys. With flanged base that can be mounted in a tight area.
Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360o controlled tensioning. Serrated teeth to prevent slippage once tightened.
Related Information:
Quick release. Commercial pins provide strong locking and are perfect for less demanding applications where fastening and locating are needed.
Economical. Positive lock detent pins. Aluminium handles. 360 Brass Buttons. 304 Stainless Steel Shank and balls. Use industrial grade T handled pins when higher double shear strength is required.
Related Information:
Quick release. Commercial pins provide strong locking and are perfect for less demanding applications where fastening and locating are needed.
Economical. Positive lock detent pins. Aluminium handles. Commercial Carbon Steel Shank and balls. 360 Brass Button. Use industrial grade T handled pins when higher double shear strength is required.
Related Information:
Quick release. Stainless steel commercial pins provide strong locking and are perfect for less demanding applications where fastening and locating are needed. Tee handle.
Economical. Positive lock detent pins. Aluminium handles. 304 Stainless Steel Shank. 360 Brass Button. Use industrial grade T handled pins when higher double shear strength is required.
Related Information:
Quick release. Stainless steel commercial pins provide strong locking and are perfect for less demanding applications where fastening and locating are needed. Tee handle.
Economical. Positive lock detent pins. Aluminium handles. Commercial Carbon Steel Shank and balls. 360 Brass Button. Use industrial grade T handled pins when higher double shear strength is required.
Related Information:
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Standard Series Timing Belts 5.080mm or 0.200 inch pitch - Double Sided.
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 3.00mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).
Related Information:
Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide.
Aluminium alloy. Finished bore with set screw locking.
Related Information:
Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide. Brass insert.
Related Information:
Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts. Suits belts 9.0 to 9.6mm wide.
Aluminium alloy and Black Oxide coated steel. Finished bore with set screw locking. Unfinished types requires drilling and tapping. Bore requires machining to finished size.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
Related Information:
Use with timing pulley stock to custom make your own pulleys
Related Information:
Use with timing pulley stock to custom make your own pulleys
Related Information:
Used for locking the ends of timing belt lengths used in reciprocating applications
Suits single and double sided belts. Black Polycarbonate with 303 stainless fasteners. Low inertia. Compact Design. Patent Pending. For MXL, XL, GT 2mm, GT 3mm, GT 5mm, HTD 3mm and HTD 5mm belt pitches.
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 19.1mm (3/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 3.18mm (1/8 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 4.76mm (3/16 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 7.93mm (5/16 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 9.53mm (3/8 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
PowerGrip(R) TruMotion(R) Timing Belts in 2.032mm or 0.080 inch pitch.
The TruMotion(R) belt construction utilizes a cream-colored polymer compound reinforced with fiberglass tensile cord and a clean polymer-free nylon tooth facing. The belt can withstand high and low temperature ranges of -40oC to +90oC, has a virtually dust-free operation and is non-marking. The belt also has a high flex life and resistance to elongation. TruMotion(R) belts have a durable wear surface for longer life and are RoHS compliant. Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. RoHs compliant.
Related Information:
Standard Series Timing Belts 2.032mm or 0.080 inch pitch. 6.35mm (1/4 inch) widths +/- 0.2mm
Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.51mm. Belt Height (W) - 1.52mm - Corner Radii ( r ) - 0.13mm. Pitch (P) - 2.032mm (0.08 inch).
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 3.0 to 3.2mm wide.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide.
2.032mm metric is equivalent to 0.080 pitch imperial. Socket Cap Screw is Supplied with Pulley. Aluminium Alloy.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With brass insert.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. With aluminium hub.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide. Moulded single or double flange. No locking device.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 6.0 to 6.4mm wide.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts. Suits belts 9.5 to 9.6mm wide
2.032mm metric is equivalent to 0.080 pitch imperial. Aluminium Alloy. Finished Through Bore Ready To Assemble.
Related Information:
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
2.032mm metric is equivalent to 0.080 pitch imperial.
Related Information:
Use with timing pulley stock to custom make your own pulleys
Related Information:
Solid precision leaded gunmetal bronze bushes. Either LG2 (C83600A) or C93200 as indicated in the listings.
Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
Related Information:
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc. Not recommended for use with precision steel or stainless steel bearings. Some sizes have special features such as serrations or small barbs (noted in description). Unground ends. Ideal for axles in robotic applications and educational projects.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 131199
products in 2163 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.