A150WAS SEEGER
Cross Referenced Part Numbers
Seeger part number A150-WASMatches our part number
Shaft Diameter (Ds): 150.00. Clip Thickness (T): 4.00. Groove Dia. (Dg): 145.00.
Part Link: CCE-15000-C
Retail Price: 0.00 (Each
)
Lower price for quantities
Stock: 1
Lower price for quantities
Stock: 1
Category Matches
Circlips
Circlips - Internal - Tabbed
DIN984 / D2000 / Seeger JK. Retaining rings. Snap Rings (USA).
Internal tabs are concentrically positioned for a concealed assembly. Tabs act as spacers for securing machine components. This category may be available in the new MBA online store at Circlips - Internal - Tabbed.
Related Information:
Clips
Push On Retaining Rings - Carbon Steel
M1465 / DTX / Seeger ZA and KS.
Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested. This category may be available in the new MBA online store at Push On Retaining Rings - Carbon Steel.
Circlips
Circlips - Grooveless
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Retaining rings. Snap Rings (USA).
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring. This category may be available in the new MBA online store at Circlips - Grooveless.
Related Information:
Circlips - Internal - Standard - Carbon Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Plain carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Carbon Steel.
Related Information:
Circlips - Internal - Standard - Stainless Steel
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).
PH15-7 Mo Stainless Steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Stainless Steel.
Related Information:
Circlips - Internal - Standard - Zinc Plated
Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).
Zinc plated carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Zinc Plated.
Related Information:
Rounthane Belts
Joinable belting. 88 Shore A hardness. Yellow colour. Temperature range -31 to 65 Deg C (-25 to 150 Deg F).
Join with Rounthane Connectors (purchased separately). Material : Non Slip Polyurethane. FDA / USDA approved. Use with grooved idler pulleys with diameters at least 8 times the belt width. Purchased per 305mm (1 foot) of length. Orders for more than one length of 305mm will be supplied as a continuous length. We can obtain more than shown in stock, please contact us for a quotation.
Related Information:
O-Rings - EPDM Rubber
Suitable for heated water and steam.
Temperature Range: -55oC to +150oC. Chemically resistant to Hydraulic Fluids. Resistant to alcohols, glycol engine coolants and SKY-DROL (phosphate ester hydraulic fluid). This category may be available in the new MBA online store at O-Rings - EPDM Rubber.
Related Information:
Mounts - Buffer - Special Purpose
Vibration dampening
Natural rubber with bonded in studs. 50 Durometer hardness. Use up to 65 Degrees C (150 Deg F). This category may be available in the new MBA online store at Mounts - Buffer - Special Purpose.
Related Information:
1500C Abu Garcia Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Calcutta 50-100-150-200-250-251-400-600 Shimano Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Washers - Thrust - DP4 Type
Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.
Operating Temperature -200o to 280o Celsius. Maximum load 250N per mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free. This category may be available in the new MBA online store at Washers - Thrust - DP4 Type.
Washers - Disc Spring - Ball Bearing Type
Specially designed for preloading the outer ring of ball bearings. C1075 steel. Includes disc springs to DIN 2093.
Ensures perfect bearing positioning with no sideways play. May be used to provide bearing preload. Load tolerance +/- 20% of load shown. This category may be available in the new MBA online store at Washers - Disc Spring - Ball Bearing Type.
Washers - Disc Spring - Carbon Steel
Includes disc springs to DIN 2093.
Manufactured under strict quality control to conform to DIN 2093. This category may be available in the new MBA online store at Washers - Disc Spring - Carbon Steel.
Washers - Disc Spring - Flange Locking Type
Used under the nuts or bolt head in bolted flange joints that are subject to thermal or mechanical shock.
The discs deflect and move with the bolted joint. Helps to compensate for loosening that may develop preventing damage and leaks caused by thermal expansion, contraction and shock. Made from 17.7 PH Stainless Steel. Temperature range minus 220 to +300o Celsius. Load tolerance +/- 20% of load shown.
Washers - Disc Spring - Plastic
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.
Washers - Disc Spring - Stainless Steel
Includes disc springs to DIN 2093 and belleville washers to DIN 6796.
Manufactured under strict quality control to conform to DIN 2093. This category may be available in the new MBA online store at Washers - Disc Spring - Stainless Steel.
Washers - Spring - 2 Wave Type - Zinc Plated
Wave Washers - All Materials.
This category may be available in the new MBA online store at Washers - Spring - 2 Wave Type - Zinc Plated.
Washers - Spring - 3 Wave Type - 302 Stainless Steel
Wave Washers - also called crinkle wave.
This category may be available in the new MBA online store at Washers - Spring - 3 Wave Type - 302 Stainless Steel.
Washers - Spring - 3 Wave Type - 400 Grade Stainless
Wave Washers - also called crinkle wave.
This category may be available in the new MBA online store at Washers - Spring - 3 Wave Type - 400 Grade Stainless.
Washers - Spring - 3 Wave Type - Berryllium Copper
Wave Washers - also called crinkle wave.
This category may be available in the new MBA online store at Washers - Spring - 3 Wave Type - Berryllium Copper.
Washers - Spring - Curved - Carbon Steel
Wave Washers - All Materials.
ID and OD are long axis dimensions. This category may be available in the new MBA online store at Washers - Spring - Curved - Carbon Steel.
Washers - Spring - Curved - Stainless Steel
Wave Washers - All Materials.
ID and OD are long axis dimensions. This category may be available in the new MBA online store at Washers - Spring - Curved - Stainless Steel.
Washers - Spring - Wave Type - Carbon Steel
Wave Washers - also called crinkle wave. Includes 2 and 3 wave types. This category includes EPL type bearing pre-load washers.
This category may be available in the new MBA online store at Washers - Spring - Wave Type - Carbon Steel.
Washers - Self Aligning - Components - Hardened Steel
Spherical Seat Washers. Washer A (aligning) and washer B (seat) sold separately.
Case Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-G washers are used for clamping mechanical parts with non-parallel surfaces. Designed for screw solidity in compliance with 8.8. Limited for use on flat closed ring areas - not for elongated holes.
Washers - Self Aligning - Sets - Hardened Steel
Spherical Seat Washers
Hardened steel 9 S Mn Pb 28 K DIN 6319. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at Washers - Self Aligning - Sets - Hardened Steel.
Washers - Self Aligning - Sets - Stainless Steel
Spherical Seat Washers
AISI 303 Stainless Steel. Max Shaft Size Shown will allow 3o of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. This category may be available in the new MBA online store at Washers - Self Aligning - Sets - Stainless Steel.
Washers - Cup - Aluminium
For countersunk screws.
Aluminium solid cup washers. This category may be available in the new MBA online store at Washers - Cup - Aluminium.
Washers - Cup - Brass - Nickel Plated
For countersunk screws.
This category may be available in the new MBA online store at Washers - Cup - Brass - Nickel Plated.
Washers - Cup - Nylon
Countersunk washers for use with screws for decorative finishing
This category may be available in the new MBA online store at Washers - Cup - Nylon.
Washers - Cup - Stainless Steel
For countersunk screws.
Stainless Steel cup washers. This category may be available in the new MBA online store at Washers - Cup - Stainless Steel.
Washers - Flat - Fibre
Also see combined categories:
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic
All Non Precision Flat Washers - Non Metallic
All Flat Washers and Spacers - Non Metallic
Flat red vulcanised fibre washers. Black available on request and sufficient quantity.
Operating temperature up to 105 oC. Tensile strength 6 kg/mm2. Elongation up to 19 percent. Shrinkage up to 3 percent thickness. Water absorption 4 to 70 percent after 24 hours. Density 1 to 1.45 g/cm.
Related Information:
Washers - C - Steel
Cold finished steel, case hardened with a black oxide finish.
This category may be available in the new MBA online store at Washers - C - Steel.
Washers - C - Swing
Cold finished steel, hardened and ground. Black oxide finish.
This category may be available in the new MBA online store at Washers - C - Swing.
Washers - Flat - Aluminium - Precision Shim
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
This category may be available in the new MBA online store at Washers - Flat - Aluminium - Precision Shim.
Related Information:
Washers - Flat - Brass - Commercial
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at Washers - Flat - Brass - Commercial.
Related Information:
Washers - Flat - Brass - Precision Shim
Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Precision Tolerances. Standard and laminated brass shim washers.
This category may be available in the new MBA online store at Washers - Flat - Brass - Precision Shim.
Related Information:
Washers - Flat - Carbon Spring Steel - Precision Shim
Flat Carbon Spring Steel Washers. Commonly used for fast and accurate spacing of milling cutters, gang cutters, saws, slitting blades and grinding tools.
C1010 steel types best suited to arbor shimming. This category may be available in the new MBA online store at Washers - Flat - Carbon Spring Steel - Precision Shim.
Related Information:
Washers - Flat - Copper - Precision Shim
Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Precision Tolerances.
This category may be available in the new MBA online store at Washers - Flat - Copper - Precision Shim.
Related Information:
Washers - Flat - Hardened Steel
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Medium carbon steel through hardened to RC 43-49. Zinc dichromate finish. All dimensions shows are minimum.
This category may be available in the new MBA online store at Washers - Flat - Hardened Steel.
Related Information:
Washers - Flat - High Tensile
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Grade 8 high tensile washers
ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - High Tensile.
Related Information:
Washers - Flat - Mild Steel
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers. Includes fender washers. Zinc plated and unplated listings.
In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD. This category may be available in the new MBA online store at Washers - Flat - Mild Steel.
Related Information:
Washers - Flat - Sintered Bronze - Precision
Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat thrust washers made from oil impregnated sintered bronze
This category may be available in the new MBA online store at Washers - Flat - Sintered Bronze - Precision.
Related Information:
Washers - Flat - Stainless Steel 304 - Commercial
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - Stainless Steel 304 - Commercial.
Related Information:
Washers - Flat - Stainless Steel 316 - Commercial
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers. This category may be available in the new MBA online store at Washers - Flat - Stainless Steel 316 - Commercial.
Related Information:
Washers - Flat - Stainless Steel - Precision Shim
Precision Tolerances.
This category may be available in the new MBA online store at Washers - Flat - Stainless Steel - Precision Shim.
Related Information:
Washers - Flat - Stamped - Heavy Duty - Hardened
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Heat treated. Black oxide finish.
This category may be available in the new MBA online store at Washers - Flat - Stamped - Heavy Duty - Hardened.
Related Information:
Washers - Flat - Titanium - CP Grade 1
Also see combined categories:
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
All Non Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat washers. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at Washers - Flat - Titanium - CP Grade 1.
Related Information:
Washers - Heavy Duty - Machined - Stainless Steel
303 Stainless Steel
This category may be available in the new MBA online store at Washers - Heavy Duty - Machined - Stainless Steel.
Related Information:
Washers - Heavy Duty - Machined - Steel
Case hardened cold finished steel with black oxide finish.
This category may be available in the new MBA online store at Washers - Heavy Duty - Machined - Steel.
Related Information:
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153564 products in 2094 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
