A11 SEEGER

Clips

Push On Retaining Rings - Carbon Steel

Also see combined categories:
All Push On Rings

M1465 / DTX / Seeger ZA and KS.

Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested. This category may be available in the new MBA online store at Push On Retaining Rings - Carbon Steel.

Circlips

Circlips - Grooveless

Also see combined categories:
All External Circlips

Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Retaining rings. Snap Rings (USA).

Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring. This category may be available in the new MBA online store at Circlips - Grooveless.

Related Information:

Circlips - Internal - Standard - Carbon Steel

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Plain carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Carbon Steel.

Related Information:

Circlips - Internal - Standard - Stainless Steel

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. PH15-7 Mo Stainless Steel. Retaining rings. Snap Rings (USA).

PH15-7 Mo Stainless Steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Stainless Steel.

Related Information:

Circlips - Internal - Standard - Zinc Plated

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / D1300 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Zinc plated carbon steel. Tolerances on request. This category may be available in the new MBA online store at Circlips - Internal - Standard - Zinc Plated.

Related Information:

Inexpensive Gearmotor Kits

Leadscrew Nuts - Metric - Square - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Related Information:

Metric Rolled Leadscrew

Metric Whirled Leadscrew

Leadscrew Nuts - Metric - Round - Metallic

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.

Related Information:

Metric Rolled Leadscrew

Metric Whirled Leadscrew

Latches - 110 Series - Adjustable Grip

Ultimate strength 145kg. Working strength 120kg.

Strike needs to be ordered separately. This category may be available in the new MBA online store at Latches - 110 Series - Adjustable Grip.

Gearboxes - Cross Axis - 110 x 95 x 38mm

Also see combined categories:
All Cross Axis Gearboxes

Worm and Wormwheel box. 10.3 to 40.0Nm. 5:1 to 120:1 ratios. P45 and PF45 Series.

Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.

Related Information:

Output Shafts

Rims - Hobby - Car 1-10 - Off Road - Front - Plastic

Also see combined categories:
All Rims

Rims for RC wheels

This category may be available in the new MBA online store at Rims - Hobby - Car 1-10 - Off Road - Front - Plastic.

Rims - Hobby - Car 1-10 - Off Road - Rear - Plastic

Also see combined categories:
All Rims

Rims for RC wheels

This category may be available in the new MBA online store at Rims - Hobby - Car 1-10 - Off Road - Rear - Plastic.

Rims - Hobby - Car 1-10 - Road and Drift - Plastic

Also see combined categories:
All Rims

Rims for RC wheels

This category may be available in the new MBA online store at Rims - Hobby - Car 1-10 - Road and Drift - Plastic.

Sprocket Plates - 19.05 x 11.68mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 19.05x11.68mm simplex steel chain (12B-1 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 12B - 3/4 inch.

Related Information:

Stainless Chain To Suit Listed Here

Steel Simplex Chain to Suit Listed Here

Belts - Vee - 16.5 x 11.0mm - B

Also see combined categories:
All Vee Belts 15.9mm and 16.5mm Top Width

16.5mm Top Width x 11.0mm Height.

Sizes are nominal and may vary slightly. This category may be available in the new MBA online store at Belts - Vee - 16.5 x 11.0mm - B.

Related Information:

Vee Pulleys - B/5L Section - Cast Iron

Vee Pulleys - Idler

Pulleys - Timing 14.000mm Pitch GT - 115mm Wide - Taperlock

Also see combined categories:
All 14mm Pitch Timing Pulleys Taperlock

Timing Pulleys to suit HTD 14.000mm Pitch Timing Belts. Suits belts 115mm wide. Taperlock. Use with GT2 or GT3 type belts.

Cast iron with black oxide coating. Match with a taperlock to suit your bore requirements. This category may be available in the new MBA online store at Pulleys - Timing 14.000mm Pitch GT - 115mm Wide - Taperlock.

Related Information:

Belts to suit 14.000 Pitch HTD Pulleys

Taperlock Bushings

Timing Pulleys Catalogue PDF

Belts - Metric Timing - 14.000mm Pitch GT - 115mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

GT2 and GT3 Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. GT3 replaces GT2 as GT2 stock is depleted. Pitch (P) - 14.000mm.

Related Information:

All 14mm Pitch Taperlock Pulleys - Choose width carefully

Timing Belts Catalogue PDF

Belts - Metric Timing - 14.000mm Pitch HTD - 115mm Wide

Also see combined categories:
All 14mm Pitch Timing Belts

HTD Series Metric Timing Belts

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Pitch (P) - 14.000mm.

Related Information:

All 14mm Pitch Taperlock Pulleys - Choose width carefully

Timing Belts Catalogue PDF

1311002 Adler Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Gearmotors - DC PM - Size 70x114

Also see combined categories:
All DC Permanent Magnet Gearmotors

Permanent Magnet.

Max. Allowable Radial Load: 100N (10mm from mounting surface). Max. Allowable Axial Load: 30N. Axial Play: 0.05 - 0.6mm. Allowable Temperature Range: -20^oC to +60^oC. Integral CD PM Motor - Brush type commutation - 12 segment commutator - RFI protection standard. Gear train with steel and high quality plastic gears - Terminal dimensions 4.8 x 0.8 - Weight: 1200g.

Shim and Foil - Aluminium

Also see combined categories:
All Shim
All Sheet

Precision aluminium shim sheet. Very thin to thick sizes.

NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Coloured shim is anodised. The colour is not removable. The colour is for identification purposes only. Includes K&S Metals range and more. Includes listings on 1100, 3003, 6061-T6 and commercial grades aluminium sheet.

Pins - Ball Lock - Shoulder Type - T Handle

Also see combined categories:
All Ball Lock Pins

Zinc plated C1144 pins with a shoulder that prevents the pin being inserted all the way to the handle. Tee handle.

Positive lock detent pins. Carbon steel components. This category may be available in the new MBA online store at Pins - Ball Lock - Shoulder Type - T Handle.

Related Information:

Pins - Ball Lock - Shoulder Type - Ring Handle

Also see combined categories:
All Ball Lock Pins

Zinc plated C1144 pins with a shoulder that prevents the pin being inserted all the way to the handle.

Positive lock detent pins. Carbon steel components. This category may be available in the new MBA online store at Pins - Ball Lock - Shoulder Type - Ring Handle.

Related Information:

Pins - Ball Lock - T Handle - Plastic Handle

Also see combined categories:
All Ball Lock Pins

Quick release. Zinc plated C1144 steel pins with black plastic ball handles and spring loaded balls. Quick alternative to cotter pins. Tee handle.

Positive lock detent pins. Plastic Handles. Carbon steel components. This category may be available in the new MBA online store at Pins - Ball Lock - T Handle - Plastic Handle.

Related Information:

Pins - Ball Lock - Ball Handle - Plastic Handle

Also see combined categories:
All Ball Lock Pins

Quick release. Zinc plated C1144 steel pins with black plastic ball handles snd spring loaded balls. Quick alternative to cotter pins.

Positive lock detent pins. Plastic Handles. 300 Grade Stainless Components. 440C Stainless Balls. This category may be available in the new MBA online store at Pins - Ball Lock - Ball Handle - Plastic Handle.

Related Information: