CLEARANCE
Category Matches
Surplus Stock
Locking Assemblies
Assemblies - Locking - Flanged
Suitable for locking sprockets, pulleys, eccentric shafts.
Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. Flange eliminates axial movement of secured component. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub.
You may also be interested in
Rod Ends PTFE Lined
Rod Ends - Steel - PTFE Lined - Tight Fit Female
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon Steel. Also known as Heim Joints
Dimensions not shown are available on request. This category may be available in the new MBA online store at Rod Ends - Steel - PTFE Lined - Tight Fit Female.
Rod Ends - Steel - PTFE Lined - Tight Fit Male
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon Steel. Also known as Heim Joints
Dimensions not shown are available on request. This category may be available in the new MBA online store at Rod Ends - Steel - PTFE Lined - Tight Fit Male.
Clamps
Clamps - Gear - Split
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Clamps - Gear - Screw Type
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
Related Information:
Springs Disc
Washers - Disc Spring - Plastic
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.
Clamping Rings
Spiral Rings - Internal - Light Duty - Carbon Steel
Includes series CI / VH / UR - Spring Steel
Light duty rings for use in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CI, Smalley: VH, Spirolox and Ramsey: UR.
Spiral Rings - Internal - Light Duty - Stainless Steel
Includes series CI / VH / UR - Stainless Steel.
Light duty rings for use in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CI, Smalley: VH, Spirolox and Ramsey: UR.
Spiral Rings - External - Light Duty - Carbon Steel
Includes series CE / VS / US - Spring Steel
Light duty single turn rings used in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CE, Smalley: VS, Spirolox and Ramsey: US.
Spiral Rings - External - Light Duty - Stainless Steel
Includes series CE / VS / US - Stainless Steel.
Light duty single turn rings used in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CE, Smalley: VS, Spirolox and Ramsey: US.
Linear Bearings
Bearings - Linear Sliding - Frelon Gold Lined - Closed - Precision
Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.
Related Information:
Bearings - Linear Sliding - Frelon Gold Lined - Open - Precision
Also see combined categories:
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.
Related Information:
Bearings - Linear Sliding - Frelon J Lined - Closed - Standard
Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon J Lined Linear Bearings
All Closed Frelon Lined Linear Bearings
All Closed Frelon J Lined Linear Bearings
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon J = 10000 PV. Dry Running Max Surface Speed Frelon J = 0.7 mtrs / sec (140 ft / min). With Lubrication Max Surface Speed Frelon J = 2 mtrs / sec (400 ft / min). Standard type has slightly larger running clearances.
Related Information:
Bearings - Linear Sliding - Frelon Gold Lined - Closed - Standard
Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Standard type has slightly larger running clearances.
Related Information:
Bearings - Linear Sliding - Frelon Gold Lined - Open - Standard
Also see combined categories:
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings
Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C
Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Standard type has slightly larger running clearances.
Related Information:
Circlips
Circlips - Internal - Inverted
M1308 / JV / INTV / BN830. Retaining rings. Snap Rings (USA).
Inverted lugs seat into the groove for better clearance and cleaner appearance. Good for shielded bearings that pass tightly through the bore or housing. Use recommended installation pliers. This category may be available in the new MBA online store at Circlips - Internal - Inverted.
Related Information:
Clips
Rings - Crescent
Variation of an E-Clip with an open face. Also known as a C-Clip.
Narrow section height provides good clearance capabilities. Absence of teeth and deep set mean less thrust load ratings than e-clips. For best results install using the recommended applicator tool. This category may be available in the new MBA online store at Rings - Crescent.
Related Information:
Bushes Plastic
Bushes - Plastic Clip - Double Flanged
For use with sheet metal. Used as a light duty split bearing.
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40 oC to 80 oC (minus 40 Deg F to 176 Deg F). This category may be available in the new MBA online store at Bushes - Plastic Clip - Double Flanged.
Related Information:
Hubs
Hubs - Gear and Dial - Single
Fairloctm Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Hubs - Gear and Dial - Single.
Related Information:
Bushes Plastic
Bushes - Plastic Clip - Bevelled Edge
M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F). Used as a light duty split bearing.
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. This category may be available in the new MBA online store at Bushes - Plastic Clip - Bevelled Edge.
Related Information:
Circlips
Circlips - External - Inverted
N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel. Retaining rings. Snap Rings (USA).
Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips. This category may be available in the new MBA online store at Circlips - External - Inverted.
Related Information:
Gears Metric Spur
Gears - Spur - Module 0.4 - Brass
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Brass.
Gears - Spur - Module 0.75 - Brass
PCD = No. of Teeth x 0.750mm. 20o Pressure Angle. Brass.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.75 - Brass.
Gears - Spur - Module 0.7 - Plastic
PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.7 - Plastic.
Gears - Spur - Module 3 - Plastic
PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 3 - Plastic.
Gears - Spur - Module 0.8 - Aluminium
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Aluminium.
Gears - Spur - Module 1.25 - Stainless
PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.25 - Stainless.
Gears - Spur - Module 0.4 - Plastic - Standard
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic - Standard.
Gears - Spur - Module 0.5 - Plastic - Standard
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic - Standard.
Gears - Spur - Module 1.5 - Plastic - Standard
PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1.5 - Plastic - Standard.
Gears - Spur - Module 0.4 - Plastic with Insert
PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.4 - Plastic with Insert.
Gears - Spur - Module 0.5 - Plastic with Insert
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Plastic with Insert.
Gears - Spur - Module 0.5 - Stainless
PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.5 - Stainless.
Gears - Spur - Module 0.8 - Plastic - Standard - Standard
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic - Standard - Standard.
Gears - Spur - Module 0.8 - Plastic with Insert
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Plastic with Insert.
Gears - Spur - Module 0.8 - Stainless
PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 0.8 - Stainless.
Gears - Spur - Module 1 - Plastic - Standard - Standard
PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at Gears - Spur - Module 1 - Plastic - Standard - Standard.
Gears - Spur - 72DP - Stainless
PCD = No. of Teeth x 0.353mm (1/72 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 72 Diametrical Pitch. Approx 1.11mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 72DP - Stainless.
Bearings - Linear Ball - Stainless Steel - Closed
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at Bearings - Linear Ball - Stainless Steel - Closed.
Related Information:
Gears - Spur - 64DP - Aluminium
PCD = No. of Teeth x 0.397mm (1/64 in.). 20o Pressure Angle. 5052 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 64 Diametrical Pitch. Approx 1.25mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 64DP - Aluminium.
Gears - Spur - 72DP - Aluminium
PCD = No. of Teeth x 0.353mm (1/72 in.). 20o Pressure Angle. 2024 aluminium. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 72 Diametrical Pitch. Approx 1.11mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 72DP - Aluminium.
Gears - Spur - 16DP - 14.5 Degree - Steel
PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 16 Diametrical Pitch. Approx 4.99mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 16DP - 14.5 Degree - Steel.
Gears - Spur - 24DP - 14.5 Degree - Brass
PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 24DP - 14.5 Degree - Brass.
Gears - Spur - 32DP - 14.5 Degree - Brass
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 32DP - 14.5 Degree - Brass.
Gears - Spur - 32DP - 14.5 Degree - Plastic
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 32DP - 14.5 Degree - Plastic.
Gears - Spur - 24DP - 14.5 Degree - Steel
PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system. Carbon Steel.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 24 Diametrical Pitch. Approx 3.33mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 24DP - 14.5 Degree - Steel.
Gears - Spur - 32DP - 14.5 Degree - Steel
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5o Pressure Angle. Carbon steel. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 32DP - 14.5 Degree - Steel.
Gears - Spur - 32DP - 20 Degree - Plastic - Standard
PCD = No. of Teeth x 0.794mm (1/32 in.). 20o Pressure Angle. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 32 Diametrical Pitch. Approx 2.49mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 32DP - 20 Degree - Plastic - Standard.
Gears - Spur - 48DP - 20 Degree - Stainless
PCD = No. of Teeth x 0.529mm (1/48 in.). 20o Pressure Angle. 303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.
FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. 48 Diametrical Pitch. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gears - Spur - 48DP - 20 Degree - Stainless.
Main Pages
About Us
Acetal Bearings PDF
ADR and SKF PDF
Anderton Circlips Cross Reference PDF
Ball Lock Pins PDF
Balls List
Balls PDF
Barden Bearings Cross Reference PDF
Bearings List
Brands
Ceramic Bearings PDF
Circlips PDF
Clearance Items List
Clevis Pins PDF
Contact Us
Corrosion Resistant Bearings PDF
Dental Bearings
Disc Springs PDF
Dowel Pins PDF
Dowel Pins
Economy Bearings PDF
Essentra Cross Reference PDF
Flocast Cross Reference PDF
Freight Rates and Shipping Times
Frequently Asked Questions
General Information about MBA
Hammer Drive Pins PDF
High Speed Bearings PDF
Hobby Clearance
Hobby Information
K&S Metals Cross Reference PDF
Key Steel PDF
Knobs PDF
Large Bearings
Leveling Mounts PDF
Mailorder Form
Metallic Bushes PDF
Miniature Precison Bearings Cross Reference PDF
Miscellaneous Brands Cross Reference PDF
Nordex Cross Reference PDF
NSK and NTN Cross Reference PDF
Ondrives Cross Reference PDF
O-Rings PDF
Pins PDF
Plastic Bearings PDF
Polyvee Belts and Pulleys PDF
Precision Shim Washers PDF
Privacy
Push On and Push In Rings PDF
Reid Supply Cross Reference PDF
Rod & Tube PDF
Roll Pins PDF
Screws PDF
SDP-SI Designatronics Cross Reference PDF
Seeger Circlips Cross Reference PDF
Shaft Collars PDF
Shim Sheet PDF
Shoulder Screws PDF
Sintered Bronze Bushes PDF
Sintered Bronze Cross Reference PDF
Small Bearings
Small Parts Inc Cross Reference PDF
Snap Rings PDF
Socket Set Screws PDF
Solid Bronze Bushes PDF
Spring Steel Strip PDF
Springs PDF
Standard Ball Bearing Range PDF
Super Precision Bearings PDF
Taper Pins PDF
Technical Information
Terms
Thrust Bearings PDF
Thumb Screws and Nuts PDF
Timing Belts and Pulleys Cross Reference PDF
Timing Belts PDF
Timing Pulley Stock PDF
Timing Pulleys PDF
Vibration Mounts PDF
Washers and Spacers PDF
Wave Washers PDF
Domains
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 153564 products in 2094 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.
