Small Parts & Bearings - an MBA company

CLEARANCE


Surplus Stock


Clearance Items
Clearance Items


Surplus items and deleted stock lines



Locking Assemblies


Assemblies - Locking - Flanged
Assemblies - Locking - Flanged

Also see combined categories:
All Locking Assemblies

Suitable for locking sprockets, pulleys, eccentric shafts.

Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. Flange eliminates axial movement of secured component. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub.


You may also be interested in

Bushes Plastic


Bushes - Plastic - Clip - Double Flanged
Bushes - Plastic - Clip - Double Flanged

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For use with sheet metal. Used as a light duty split bearing.

Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40 oC to 80 oC (minus 40 Deg F to 176 Deg F).

Related Information:


Rod Ends PTFE Lined


Rod Ends - Steel - PTFE Lined - Tight Fit - Female
Rod Ends - Steel - PTFE Lined - Tight Fit - Female

Also see combined categories:
All Female Rod Ends
All Steel Female Rod Ends

Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon Steel. Also known as Heim Joints

Dimensions not shown are available on request.


Rod Ends - Steel - PTFE Lined - Tight Fit - Male
Rod Ends - Steel - PTFE Lined - Tight Fit - Male

Also see combined categories:
All Male Rod Ends
All Steel Male Rod Ends

Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon Steel. Also known as Heim Joints

Dimensions not shown are available on request.


Rod Ends Stainless Steel


Rod Ends - Stainless Steel 303 with 420 Ball - PTFE Lined - Male
Rod Ends - Stainless Steel 303 with 420 Ball - PTFE Lined - Male

Also see combined categories:
All Male Rod Ends
All Stainless Steel Male Rod Ends

Tight fit (Minimal ball clearance). Also known as Heim Joints

Dimensions not shown are available on request.


Circlips


Circlips - Internal - Inverted
Circlips - Internal - Inverted

Also see combined categories:
All Internal Circlips

M1308 / JV / INTV / BN830. Retaining rings. Snap Rings (USA).

Inverted lugs seat into the groove for better clearance and cleaner appearance. Good for shielded bearings that pass tightly through the bore or housing. Use recommended installation pliers.

Related Information:


Hubs


Hubs - Gear and Dial - Single
Hubs - Gear and Dial - Single

Also see combined categories:
All Hubs

Fairloctm Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.

Related Information:


Clamps


Clamps - Gear - Split
Clamps - Gear - Split

Also see combined categories:
All Gear Clamps

Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.

Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.

Related Information:


Clips


Rings - Crescent
Rings - Crescent


Variation of an E-Clip with an open face. Also known as a C-Clip.

Narrow section height provides good clearance capabilities. Absence of teeth and deep set mean less thrust load ratings than e-clips. For best results install using the recommended applicator tool.

Related Information:


Clamps


Clamps - Gear - Screw Type
Clamps - Gear - Screw Type

Also see combined categories:
All Gear Clamps

Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.

Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.

Related Information:


Bushes Plastic


Bushes - Plastic - Clip - Bevelled Edge
Bushes - Plastic - Clip - Bevelled Edge

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F). Used as a light duty split bearing.

Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight.

Related Information:


Ball Joints


Joints - Ball and Socket - Right Angle - Light Duty
Joints - Ball and Socket - Right Angle - Light Duty


Light duty ball joints provide a pivot point. They are unhardened and should not be used for high load or high repetition applications. Clearance is not specified, so actual joints may range from very loose to reasonably tight.

Steel Type: Zinc Passivated Induction Hardened. Stainless Steel Type: 303 Grade unhardened. Max. Static push/pull loads are valid for both radial and axial loads. Standard Steel type Ball Stud Tensile strength: Rm = 600 N/mm sq (Not applicable to stainless type). Standard Steel type Housing Tensile strength: Rm = 500 N/mm sq (Not applicable to stainless type).


Clamping Rings


Spiral Rings - Internal - Light Duty
Spiral Rings - Internal - Light Duty

Also see combined categories:
All Internal Spiral Rings

Includes series CI / VH / UR - Spring Steel and Stainless Steel.

Light duty rings for use in low clearance applications. Also used as a positioning point for light loads. Radius notch on one end for removal. Narrow radial wall yields moderate thrust loads. Equivalent to Associated Spring: CI, Smalley: VH, Spirolox and Ramsey: UR.


Linear Bearings


Bearings - Linear - Ball - Closed
Bearings - Linear - Ball - Closed

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Related Information:


Circlips


Circlips - External - Inverted
Circlips - External - Inverted

Also see combined categories:
All External Circlips

N1408 / SHI / 16626 / 4100 / 5108 - Spring Steel and Stainless Steel. Retaining rings. Snap Rings (USA).

Tapered section ring with lugs inverted on the ID to allow use in tight areas with minimal clearance. Less thrust load than standard circlips.

Related Information:


Springs Disc


Washers - Disc Spring - Plastic
Washers - Disc Spring - Plastic

Also see combined categories:
All Disc Springs

Also known as belleville washers.

Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb(R) material.


Linear Bearings


Bearings - Linear - Frelon J Lined - Closed - Precision
Bearings - Linear - Frelon J Lined - Closed - Precision

Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon J Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon J = 10000 PV. Dry Running Max Surface Speed Frelon J = 0.7 mtrs / sec (140 ft / min). With Lubrication Max Surface Speed Frelon J = 2 mtrs / sec (400 ft / min). Precision type has closer running clearances.

Related Information:


Bearings - Linear - Frelon Gold Lined - Closed - Precision
Bearings - Linear - Frelon Gold Lined - Closed - Precision

Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.

Related Information:


Bearings - Linear - Frelon Gold Lined - Open - Precision
Bearings - Linear - Frelon Gold Lined - Open - Precision

Also see combined categories:
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Precision type has closer running clearances.

Related Information:


Bearings - Linear - Frelon J Lined - Closed - Standard
Bearings - Linear - Frelon J Lined - Closed - Standard

Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon J Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon J = 10000 PV. Dry Running Max Surface Speed Frelon J = 0.7 mtrs / sec (140 ft / min). With Lubrication Max Surface Speed Frelon J = 2 mtrs / sec (400 ft / min). Standard type has slightly larger running clearances.

Related Information:


Bearings - Linear - Ball - Stainless Steel - Closed
Bearings - Linear - Ball - Stainless Steel - Closed

Also see combined categories:
All Closed Linear Ball Bearings

Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.

Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.

Related Information:


Bearings - Linear - Frelon Gold Lined - Closed - Standard
Bearings - Linear - Frelon Gold Lined - Closed - Standard

Also see combined categories:
All Closed Frelon Lined Linear Bearings
All Closed Frelon Gold Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Standard type has slightly larger running clearances.

Related Information:


Bearings - Linear - Frelon Gold Lined - Open - Standard
Bearings - Linear - Frelon Gold Lined - Open - Standard

Also see combined categories:
All Open Frelon Lined Linear Bearings
All Open Frelon Gold Lined Linear Bearings

Self lubricating. Eliminates galling and shaft damage. Dampens vibration for quiet smooth operation. High load capacity. Absorbs shock loads. Maintenance free. Chemically inert. Temp range -240 Deg C to +260 Deg C

Frelon Gold = 20000 PV. Dry Running Max Surface Speed Frelon Gold = 1.5 mtrs / sec (300 ft / min). With Lubrication Max Surface Speed Frelon Gold = 4.1 mtrs / sec (825 ft / min). Interaction of the Frelon Gold material and the shafting creates a microscopic transfer of Frelon Gold to the running surfaces filling the valleys during the initial break-in period. Standard type has slightly larger running clearances.

Related Information:


Gears Metric Spur


Gears - Spur - Module 0.15 - Brass
Gears - Spur - Module 0.15 - Brass


PCD = No. of Teeth x 0.150mm. 20o Pressure Angle.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.4 - Brass
Gears - Spur - Module 0.4 - Brass

Also see combined categories:
All Module 0.4 Spur Gears
All Metal Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.5 - Brass
Gears - Spur - Module 0.5 - Brass

Also see combined categories:
All Module 0.5 Spur Gears
All Metal Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.75 - Brass
Gears - Spur - Module 0.75 - Brass


PCD = No. of Teeth x 0.750mm. 20o Pressure Angle. Brass.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.7 - Plastic
Gears - Spur - Module 0.7 - Plastic


PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.8 - Brass
Gears - Spur - Module 0.8 - Brass

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 1 - Brass
Gears - Spur - Module 1 - Brass

Also see combined categories:
All Module 1.0 Spur Gears
All Metal Module 1.0 Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Spur Gears Circular Pitch


Gears - Spur - Circular Pitch 2 - Steel
Gears - Spur - Circular Pitch 2 - Steel


PCD = No. of Teeth x 0.636mm (2.000 / Pi.). Various styles. Carbon steel.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Circular Pitch 5 - Steel
Gears - Spur - Circular Pitch 5 - Steel


PCD = No. of Teeth x 1.591mm (5.000 / Pi.). Various styles. Carbon steel.

FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears Metric Spur


Gears - Spur - Module 0.4 - Plastic
Gears - Spur - Module 0.4 - Plastic

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.5 - Plastic
Gears - Spur - Module 0.5 - Plastic

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.8 - Plastic
Gears - Spur - Module 0.8 - Plastic

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 1.25 - Plastic
Gears - Spur - Module 1.25 - Plastic

Also see combined categories:
All Module 1.25 Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. Acetal.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 1 - Plastic
Gears - Spur - Module 1 - Plastic

Also see combined categories:
All Module 1.0 Spur Gears
All Plastic Module 1.0 Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 2.5 - Plastic
Gears - Spur - Module 2.5 - Plastic

Also see combined categories:
All Module 2.5 Spur Gears

PCD = No. of Teeth x 2.500mm. 20o Pressure Angle. Nylon

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 3 - Plastic
Gears - Spur - Module 3 - Plastic

Also see combined categories:
All Module 3.0 Spur Gears

PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.4 - Plastic with Insert
Gears - Spur - Module 0.4 - Plastic with Insert

Also see combined categories:
All Module 0.4 Spur Gears
All Plastic Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.4 - Stainless
Gears - Spur - Module 0.4 - Stainless

Also see combined categories:
All Module 0.4 Spur Gears
All Metal Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. 416 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.4 - Steel
Gears - Spur - Module 0.4 - Steel

Also see combined categories:
All Module 0.4 Spur Gears
All Metal Module 0.4 Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Carbon steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.5 - Aluminium
Gears - Spur - Module 0.5 - Aluminium

Also see combined categories:
All Module 0.5 Spur Gears
All Metal Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 2024 aluminium

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.5 - Plastic with Insert
Gears - Spur - Module 0.5 - Plastic with Insert

Also see combined categories:
All Module 0.5 Spur Gears
All Plastic Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.5 - Steel
Gears - Spur - Module 0.5 - Steel

Also see combined categories:
All Module 0.5 Spur Gears
All Metal Module 0.5 Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Carbon steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.8 - Aluminium
Gears - Spur - Module 0.8 - Aluminium

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.8 - Plastic with Insert
Gears - Spur - Module 0.8 - Plastic with Insert

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.8 - Plastic with Stainless Hub
Gears - Spur - Module 0.8 - Plastic with Stainless Hub

Also see combined categories:
All Module 0.8 Spur Gears
All Plastic Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Gears - Spur - Module 0.8 - Steel
Gears - Spur - Module 0.8 - Steel

Also see combined categories:
All Module 0.8 Spur Gears
All Metal Module 0.8 Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Carbon steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 126240 products in 2738 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 126240 products in 2738 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts & Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.