Washers Thrust Categories
- from Small Parts and Bearings
Category Matches
Washers Thrust
TopHide PicturesWashers - Thrust - DP4 Type

Search Rating: 100%
Also see combined categories:
All Thrust Washers
Wear resistant helping to prevent wear deposits in the lubricating oil after long working periods. Designed for use in oil pumps and dampers.
Operating Temperature -200o to 280o Celsius. Maximum load 250N per mm2. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.
Bearings Thrust
TopHide PicturesBearings - Thrust - Ball - Washers Only - Chrome Steel

Search Rating: 73%
Also see combined categories:
All Ball Thrust Bearing Components
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Carbon Steel Washers are hardened to RC59.61.
Bearings - Thrust - Ball - Washers Only - Stainless Steel

Search Rating: 73%
Also see combined categories:
All Ball Thrust Bearing Components
Hardened thrust washers for thrust bearings - ungrooved. Match with thrust ball and retainer or roller type.
Stainless Steel Washers are hardened to HRC38.42.
Bearings - Thrust - Roller - Washers

Search Rating: 73%
Also see combined categories:
All Roller Thrust Cages and Washers
Washers and Rollers sold separately. Match washers with cage and roller assembly from the cage and roller assembly category.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
Washers - Self Aligning - Sets - Plastic

Search Rating: 73%
Also see combined categories:
All Thrust Washers
All Aligning Washers
Spherical Seat Washers
Tensile strengths shown are Static Axial in Newtons. Easy to install. Good friction wear properties.
Washers Flat Metallic
TopHide PicturesWashers - Flat - Sintered Bronze - Precision

Search Rating: 72%
Also see combined categories:
All Precision Flat Washers - Metallic
All Flat Washers and Spacers - Metallic
Flat thrust washers made from oil impregnated sintered bronze
Bearings Thrust
TopHide PicturesBearings - Thrust - Roller - Cage and Rollers Only

Search Rating: 72%
Also see combined categories:
All Roller Thrust Cages and Washers
Washers and Rollers sold separately. Match cage and roller assembly with washers from the washers category.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
Bearings - Thrust - Ball - Cage and Balls Only - Stainless Steel

Search Rating: 70%
Also see combined categories:
All Ball Thrust Bearing Components
Match with thrust washers of the same bore and OD.
Bearings - Thrust - Ball - Flat - Chrome Steel

Search Rating: 70%
Also see combined categories:
All Ball Thrust Bearings
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Bearings - Thrust - Ball - Flat - Stainless Steel

Search Rating: 70%
Also see combined categories:
All Ball Thrust Bearings
3 Piece Thrust Bearings Open Type with Flat Washers
These bearings are designed so that when one ring turns, the other remains stationary. Some have a larger bore on one side allowing a shaft with no steps to pass through. Others will require a stepped shaft as they have the same bore on both races. Some have a reduced size OD on one race allowing it to sit into an unstepped housing bore, whilst others will require a stepped housing to allow one ring to rotate. Please be sure to take note of the figures shown for ID and OD of both races to ensure you select the correct bearing.
Plungers Indexing
TopHide PicturesWashers - for Indexing Pull Knobs

Search Rating: 37%
The washer is slid beneath the disengaged pull knob so that the follower pins engage in the slot.
Other Store Pages
Click Page Banner Below
TopMain Pages
Click Page Banner Below
Top



Clearance

Contact




Freight


Hobby




Payments

Privacy

Products



Technical

Terms
Top