All Items: Tensioners

Tensioner - Adjustable Screw

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Uses a screw adjustment for positive precise tensioning.

Idler shaft and pulleys not included with tensioner.

Tensioner - Drive - Adjustable Flanged

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. With flanged base that can be mounted in a tight area.

Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360^o controlled tensioning. Serrated teeth to prevent slippage once tightened.

Tensioner - Drive - Double Adjust - Base Mount

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Adjusting slot assists with precise adjustments.

Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360^o controlled tensioning. Serrated teeth to prevent slippage once tightened.

Tensioner - Drive - Single Adjusting - Shaft Mount

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Mounts on any free point of a fixed shaft allowing controlled tensioning around 360^o.

Idler shaft and pulleys not included with tensioner.

Tensioner - Fixed Angle

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Can be mounted on top of any flat surface to provide horizontal tenaioning.

Idler shaft and pulleys not included with tensioner.

Tensioner - Fixed Flanged

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Compact design allows mounting where space is limited.

Idler shaft and pulleys not included with tensioner.

Tensioner - Heavy Duty - Type 1

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws.

Tensioner - Heavy Duty - Type 2

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted to the side at 90^o and is anchored by set screws.

Tensioner - Heavy Duty - Type 3

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Shaft is located in the centre of the tensioner between the adjusting slots.

Tensioner - Heavy Duty - Type 4

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 152.4mm travel through the use of the adjusting slots. Head is drilled and tapped to accept 50.8mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner. Shaft is mounted straight out from face and anchored by set screws. Adjusting slots are parallel to each other.

Tensioner - Horizontal Mount

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 88.9mm travel and is mounted 90^o to the length of the part. Both ends are tapped so the shaft can be threaded on either side of the tensioner.

Idler shaft and pulleys not included with tensioner. Hole is tapped to accept 38.1mm diameter idler shaft (ordered separately).

Tensioner - Vertical Mount

Match Strength: 100%

Also see combined categories:
All Tensioner Arms

Use with idler shafts and idler pulleys. Has 88.9mm travel through the use of the vertical slot. Head is drilled and tapped to accept 38.1mm diameter idler shaft (ordered separately).

Idler shaft and pulleys not included with tensioner.

Studs - Shoulder - Machine

Match Strength: 62%

Machine shoulder studs can be used with idlers or tensioner arms

Shafts - Idler

Match Strength: 53%

Ready made precision ground idler shafts.

Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design.