Tensioners
Use with idler shafts and idler pulleys. Fixed base with adjustable arm through 360o.
Related Information:
Use with idler shafts and idler pulleys. With flanged base that can be mounted in a tight area.
Idler shaft and pulleys not included with tensioner. Rotating arm gives operator 360
o controlled tensioning. Serrated teeth to prevent slippage once tightened. This category may be available in the new MBA online store at
Tensioner - Drive - Adjustable Flanged.
Related Information:
Use with idler shafts and idler pulleys. Uses a screw adjustment for positive precise tensioning.
Idler shaft and pulleys not included with tensioner. This category may be available in the new MBA online store at
Tensioner - Adjustable Screw.
Related Information:
You may also be interested in
Studs
Machine shoulder studs can be used with idlers or tensioner arms
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design. This category may be available in the new MBA online store at
Shafts - Idler.
Related Information:
Flat tip grub screws
Related Information:
For running on shafts fixed at the ends.
Related Information:
Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass insert.
Related Information:
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100
oC Intermittent, 80 Deg C continuous. This category may be available in the new MBA online store at
Bearings - Linear - Ball - Stainless Steel - Closed.
Related Information:
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64. This category may be available in the new MBA online store at
Bushings - Drill - Liner Type - Headless.
Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 62-64. This category may be available in the new MBA online store at
Bushings - Drill - Slip - With Head.
Spacers for printed circuit boards
These spacers have a hex in the centre to allow for holding with a spanner whilst tightening. Fix using a 6 or 8 gauge self tapping screw. This category may be available in the new MBA online store at
Spacers - PCB.
Designed to guide, position, and support the cutting tool in a metalworking jig.
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction. This category may be available in the new MBA online store at
Housings - Bearing - Single Assembly.
440C Hardened to RC 55-58.
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at
Balls - Fixture - Stainless Steel.
Related Information:
RC 65-68
Ball and shank are concentric within 5 microns (0.0002 in.) TIR. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. This category may be available in the new MBA online store at
Balls - Fixture - Tungsten Carbide.
Related Information:
Used in construction of tool, jig and fixture work. 4140L heat treated steel with black oxide finish.
Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.
Related Information:
Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.
Related Information:
Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.
Related Information:
Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.
Related Information:
Aluminium Body. For fixturing small parts in tight areas. Ideal for positioning and chucking flat or round parts for profile clamping.
Related Information:
Used for work feeders for production milling, positioning fixutres, work holding devices, checking fixtures, shuttle devices, assembly equipment, etc.
Tapered gibs are adjusted with a single screw that moves the gib on the taper. This type remains parallel and wears less as it occurs over the entire surface. Made of continuous cast GS 40,000 PSI pearlitic grey iron. Able to be milled, drilled, tapped, etc. This category may be available in the new MBA online store at
Slides - Dovetail.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is hardened and ground smooth. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is hardened and ground smooth. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Insulator shield prevents loss of magnetic flux when inserted into steel components or fixtures
Shielded magnets supply holding forces in limited areas of steel tools, dies and fixtures. This category may be available in the new MBA online store at
Magnets - Rare Earth - Shielded.
Spring stops are used extensively in the locating of parts in jigs and fixtures, particularly where fixture walls are not available. Plunger is case hardened low carbon steel. Properly radiused nose for perfect fit with no wobble. Aluminium body.
Spyraflo robust light weight aluminium housing with self aligning bronze bearings.
See links at bottom of web page for more information. +/- 5% Static Alignment. Sintered aluminium housing. Corrosion Resistant. Light weight.
Related Information:
Spyraflo low profile self aligning flange mounted acetal Delrin AF bearings
Related Information:
Spyraflo low profile self aligning flange mounted acetal Delrin bearings
Related Information:
Spyraflo robust light weight aluminium housing with self aligning needle roller bearings
See links at bottom of web page for more information. +/- 5% Static Alignment. Sintered aluminium housing. Corrosion Resistant. Light weight.
Related Information:
Stainless Steel.
Starting at 8mm bore size, aluminium silver series housings with removable chrome steel bearing
Related Information:
Related Information:
Related Information:
Related Information:
Related Information:
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings. This category may be available in the new MBA online store at
Housings - Bearing - Flanged - Offset - Cast Iron.
Related Information:
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings. This category may be available in the new MBA online store at
Housings - Bearing - Flanged - Round - Cast Iron.
Related Information:
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings. This category may be available in the new MBA online store at
Housings - Bearing - Flanged - Square - Cast Iron.
Related Information:
Stainless Steel Bearings with Flanges.
Single row radial ball bearings with flanges. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at
Bearings - Ball - Flanged - 440C Stainless.
Related Information:
Chrome Steel Bearings with Flanges.
Single row radial ball bearings with flanges. Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at
Bearings - Ball - Flanged - Chrome Steel.
Related Information:
Stainless Steel Bearings with Flanges - Abec 5 and Abec 7.
Single row radial ball bearings with flanges. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive). This category may be available in the new MBA online store at
Bearings - Ball - Flanged - High Precision - 440C Stainless.
Related Information:
Stainless Steel Bearings with Flanges.
Single row radial ball bearings with flanges and extended inner rings (wide inner rings). Miniature sizes from 1mm to 10mm bore and larger sizes to over 50mm bore. This category may be available in the new MBA online store at
Bearings - Ball - Flanged - WIR - 440C Stainless.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.