Small Parts & Bearings - an MBA company

Sprockets ladder chain 8.966mm pitch size 17 categories


Chain and Sprockets Ladder


Sprockets - Ladder Chain - 4.242mm Pitch - Size 21
Sprockets - Ladder Chain - 4.242mm Pitch - Size 21

Also see combined categories:
All Sprockets for Ladder Chain

Plastic.

This category may be available in the new MBA online store at Sprockets - Ladder Chain - 4.242mm Pitch - Size 21.

Related Information:


Sprockets - Ladder Chain - 7.264mm Pitch - Size 18
Sprockets - Ladder Chain - 7.264mm Pitch - Size 18

Also see combined categories:
All Sprockets for Ladder Chain

Plastic, bronze and steel.

This category may be available in the new MBA online store at Sprockets - Ladder Chain - 7.264mm Pitch - Size 18.

Related Information:


Sprockets - Idler
Sprockets - Idler


Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.

Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners. This category may be available in the new MBA online store at Sprockets - Idler.

Related Information:


Sprockets - 3.75 x 1.6mm - Simplex - Stainless Steel - Plain Bore
Sprockets -  3.75 x 1.6mm - Simplex - Stainless Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Miniature 3.75mm Pitch.

Match with 3.75mm simplex chain. This category may be available in the new MBA online store at Sprockets - 3.75 x 1.6mm - Simplex - Stainless Steel - Plain Bore.

Related Information:


Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.

Related Information:


Sprocket Plates - 9.53 x 5.7mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates -  9.53 x 5.7mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 9.53x5.7mm steel chain (06B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch.

Related Information:


Sprocket Plates - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.85mm simplex chain (40-1 ASA)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.

Related Information:


Sprocket Plates - 19.05 x 11.68mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates - 19.05 x 11.68mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 19.05x11.68mm simplex steel chain (12B-1 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 12B - 3/4 inch.

Related Information:


Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Taperlock Bored sprockets need to be matched up with a taperlock bush to obtain the correct bore size. British Standard 08B - 1/2 inch. This category may be available in the new MBA online store at Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Taperlock.

Related Information:


Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm simplex chain (08B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs. This category may be available in the new MBA online store at Sprockets - 12.7 x 7.75mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Sprockets - 9.53 x 5.7mm - Simplex - Carbon Steel - Plain Bore
Sprockets -  9.53 x 5.7mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 9.53x5.7mm steel chain (06B BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch. This category may be available in the new MBA online store at Sprockets - 9.53 x 5.7mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.75mm duplex chain (08B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. This category may be available in the new MBA online store at Sprockets - 12.7 x 7.75mm - Duplex - Carbon Steel - Plain Bore.

Related Information:


Sprockets - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 12.70x7.85mm simplex chain (40-1 ASA)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. American Standard 40-1 - 1/2 inch. With and without hubs. This category may be available in the new MBA online store at Sprockets - 12.7 x 7.85mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore
Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 15.90x9.65mm duplex steel chain (10B-2 BS)

Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch. This category may be available in the new MBA online store at Sprockets - 15.88 x 9.65mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Sprockets - 3.12 x 1.47mm - Simplex - Plastic
Sprockets -  3.12 x 1.47mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 3.12mm miniature plastic chain. This category may be available in the new MBA online store at Sprockets - 3.12 x 1.47mm - Simplex - Plastic.

Related Information:


Sprockets - 3.75 x 1.6mm - Simplex - Plastic
Sprockets -  3.75 x 1.6mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 3.75mm miniature plastic or stainless chain. This category may be available in the new MBA online store at Sprockets - 3.75 x 1.6mm - Simplex - Plastic.

Related Information:


Sprockets - 6.35 x 2.8mm - Simplex - Plastic
Sprockets -  6.35 x 2.8mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 6.35mm plastic or steel chain (25-1 ASA). American Standard 25-1 - 1/4 inch. This category may be available in the new MBA online store at Sprockets - 6.35 x 2.8mm - Simplex - Plastic.

Related Information:


Sprockets - 9.53 x 4.7mm - Simplex - Plastic
Sprockets -  9.53 x 4.7mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 9.53x4.7mm plastic or steel chain (35-1 ASA). American Standard 35-1 - 3/8 inch. This category may be available in the new MBA online store at Sprockets - 9.53 x 4.7mm - Simplex - Plastic.

Related Information:


Sprockets - 9.53 x 5.7mm - Simplex - Plastic
Sprockets -  9.53 x 5.7mm - Simplex - Plastic

Also see combined categories:
All Sprockets for Roller Chain

Nylon - Acetal - With and without bore inserts.

Match with series 9.53x5.7mm steel chain (06B BS). British Standard 06B - 3/8 inch. This category may be available in the new MBA online store at Sprockets - 9.53 x 5.7mm - Simplex - Plastic.

Related Information:


Sprockets - 6.35 x 2.8mm - Simplex - Carbon Steel - Finished Bore
Sprockets -  6.35 x 2.8mm - Simplex - Carbon Steel - Finished Bore

Also see combined categories:
All Sprockets for Roller Chain

25-1 ASA 1/4 Inch. With finished bore.

Match with 6.35mm simplex chain. American Standard 25-1 - 1/4 inch. This category may be available in the new MBA online store at Sprockets - 6.35 x 2.8mm - Simplex - Carbon Steel - Finished Bore.

Related Information:


Sprockets - 6.35 x 2.8mm - Simplex - Carbon Steel - Plain Bore
Sprockets -  6.35 x 2.8mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

25-1 ASA 1/4 Inch. With unfinished bore.

Match with 6.35mm simplex chain. American Standard 25-1 - 1/4 inch. This category may be available in the new MBA online store at Sprockets - 6.35 x 2.8mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Sprockets - 6.35 x 2.8mm - Simplex - Stainless Steel - Plain Bore
Sprockets -  6.35 x 2.8mm - Simplex  - Stainless Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

25-1 ASA 1/4 Inch. Stainless Steel 303 grade with unfinished bore.

Match with 6.35mm simplex chain. American Standard 25-1 - 1/4 inch. This category may be available in the new MBA online store at Sprockets - 6.35 x 2.8mm - Simplex - Stainless Steel - Plain Bore.

Related Information:


Sprockets - 9.53 x 4.7mm - Simplex - Carbon Steel - Plain Bore
Sprockets -  9.53 x 4.7mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

Match with 9.53x4.7mm steel chain (35-1 ASA)

Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch. This category may be available in the new MBA online store at Sprockets - 9.53 x 4.7mm - Simplex - Carbon Steel - Plain Bore.

Related Information:


Sprocket Plates - 6.35 x 2.8mm - Simplex - Carbon Steel - Plain Bore
Sprocket Plates -  6.35 x 2.8mm - Simplex - Carbon Steel - Plain Bore

Also see combined categories:
All Sprockets for Roller Chain

25-1 ASA 1/4 Inch

Match with 6.35mm simplex chain. American Standard 25-1 - 1/4 inch.

Related Information:


Bushings - QD
Bushings - QD


Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing

Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley. This category may be available in the new MBA online store at Bushings - QD.

Related Information:


Belts - Timing - 3.000mm Pitch - S3M - 15mm Wide
Belts - Timing -  3.000mm Pitch - S3M - 15mm Wide

Also see combined categories:
All 3mm Pitch Timing Belts

S3M Series Timing Belts - Limited Range. Enquire for sizes not listed.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Pitch (P) - 3.000mm.

Related Information:


Belts - Timing - 3.000mm Pitch - S3M - 6mm Wide
Belts - Timing -  3.000mm Pitch - S3M - 6mm Wide

Also see combined categories:
All 3mm Pitch Timing Belts

S3M Series Timing Belts - Limited Range. Enquire for sizes not listed.

Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Pitch (P) - 3.000mm.

Related Information:


Belts - Timing - 1.500mm Pitch - TN15 Bando - 15mm Wide
Belts - Timing -  1.500mm Pitch - TN15 Bando - 15mm Wide

Also see combined categories:
All 1.5mm Pitch Timing Belts

TN15 Series Bando Timing Belts - Limited Range. Enquire for sizes not listed.

Belt working load should be rated at approximately 1/15th of their ultimate breaking strength. Overall Height (H1) - 1.3mm. Tooth Height (H2) - 0.7mm. Pitch (P) - 1.500mm. Pitch (P) - 1.500mm.

Related Information:


Pulleys - Timing - 9.525mm Pitch - L - 12.7mm Wide - Through Bore
Pulleys - Timing -  9.525mm Pitch - L -  12.7mm Wide - Through Bore

Also see combined categories:
All L 9.525mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.

Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.

Related Information:


Pulleys - Timing - 9.525mm Pitch - L - 19.1mm Wide - Through Bore
Pulleys - Timing -  9.525mm Pitch - L -  19.1mm Wide  - Through Bore

Also see combined categories:
All L 9.525mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.

Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.

Related Information:


Pulleys - Timing - 9.525mm Pitch - L - 25.4mm Wide - Through Bore
Pulleys - Timing -  9.525mm Pitch - L -  25.4mm Wide - Through Bore

Also see combined categories:
All L 9.525mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.

Aluminium alloy and steel. Aluminium have finished bore with set screw. Steel have either finished or unfinished bore as shown in the listings. Unfinished types requires drilling and tapping. Unfinished bore type requires machining to finished size.

Related Information:


General Derailer Sprocket Parts
General Derailer Sprocket Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Gear Racks - 16DP - Steel
Gear Racks -  16DP - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.

16 DP. Approx 4.99mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gear Racks - 16DP - Steel.


Gear Racks - 16DP - Plastic
Gear Racks -  16DP - Plastic

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.

16 DP. Approx 4.99mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gear Racks - 16DP - Plastic.


Gear Racks - 12DP - Steel
Gear Racks -  12DP - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

12 DP. Approx 6.65mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gear Racks - 12DP - Steel.


Gear Racks - 24DP - 14.5 PA - Plastic
Gear Racks -  24DP - 14.5 PA - Plastic

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. DP stands for Diametrical Pitch imperial sizes.

24 DP. Approx 3.33mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gear Racks - 24DP - 14.5 PA - Plastic.


Gear Racks - 24DP - Stainless
Gear Racks -  24DP - Stainless

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.

24 DP. Approx 3.33mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gear Racks - 24DP - Stainless.


Gear Racks - 32DP - 14.5 PA - Plastic
Gear Racks -  32DP - 14.5 PA - Plastic

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.

32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gear Racks - 32DP - 14.5 PA - Plastic.


Gear Racks - 48DP - 14.5 PA - Plastic
Gear Racks -  48DP - 14.5 PA - Plastic

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Nylon. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 48 DP. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gear Racks - 48DP - 14.5 PA - Plastic.


Gear Racks - 48DP - Stainless
Gear Racks -  48DP - Stainless

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 48 DP. Approx 1.66mm between teeth. This category may be available in the new MBA online store at Gear Racks - 48DP - Stainless.


Gear Racks - 64DP - Stainless
Gear Racks -  64DP - Stainless

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 64 DP. Approx 1.25mm between teeth. This category may be available in the new MBA online store at Gear Racks - 64DP - Stainless.


Gear Racks - 96DP - Stainless
Gear Racks -  96DP - Stainless

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 96 DP. Approx 0.83mm between teeth. This category may be available in the new MBA online store at Gear Racks - 96DP - Stainless.


Gear Racks - 10DP - 14.5 PA - Steel
Gear Racks - 10DP - 14.5 PA - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 10 DP. Approx 7.98mm between teeth. This category may be available in the new MBA online store at Gear Racks - 10DP - 14.5 PA - Steel.


Gear Racks - 20DP - 14.5 PA - Steel
Gear Racks - 20DP - 14.5 PA - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 20 DP. Approx 3.99mm between teeth. This category may be available in the new MBA online store at Gear Racks - 20DP - 14.5 PA - Steel.


Gear Racks - 32DP - Stainless Steel
Gear Racks -  32DP - Stainless Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.

32 DP. Approx 2.49mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gear Racks - 32DP - Stainless Steel.


Gear Racks - 6DP - 14.5 PA - Steel
Gear Racks -  6DP - 14.5 PA - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 6 DP. Approx 13.3mm between teeth. This category may be available in the new MBA online store at Gear Racks - 6DP - 14.5 PA - Steel.


Gear Racks - 8DP - 14.5 PA - Steel
Gear Racks -  8DP - 14.5 PA - Steel

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

14.5o Pressure Angle. Unhardened Steel. DP stands for Diametrical Pitch imperial sizes.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. 8 DP. Approx 9.98mm between teeth. This category may be available in the new MBA online store at Gear Racks - 8DP - 14.5 PA - Steel.


Assemblies - Locking - Flanged
Assemblies - Locking - Flanged

Also see combined categories:
All Locking Assemblies

Suitable for locking sprockets, pulleys, eccentric shafts.

Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. Flange eliminates axial movement of secured component. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub.


Gear Racks - 96DP - Stainless - Side Holes
Gear Racks -  96DP - Stainless - Side Holes

Also see combined categories:
All Imperial Gear Racks
All All Gear Racks

20o Pressure Angle. 416 stainless steel. DP stands for Diametrical Pitch imperial sizes.

96 DP. Approx 0.83mm between teeth. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. This category may be available in the new MBA online store at Gear Racks - 96DP - Stainless - Side Holes.


Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore
Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore

Also see combined categories:
All H 12.7mm Pitch Timing Pulleys Through Bore

Timing Pulleys to suit H Series 12.700mm Pitch. Unfinished Bore.

Cast Iron and Steel. Hub requires drilling and tapping. Bore requires machining to finished size. This category may be available in the new MBA online store at Pulleys - Timing - 12.700mm Pitch - H - 25.4mm Wide - Through Bore.

Related Information:





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138615 products in 2015 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138615 products in 2015 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.