snap bushings categories


Category Matches

Bushes Plastic

TopHide Pictures

Bushings - Snap - Closed
Bushings - Snap - Closed

Search Rating: 100%

Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.

Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber.

Related Information:

Bushings - Snap - Open
Bushings - Snap - Open

Search Rating: 100%

Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.

Also called a dome plug. Also see grommets for a similar product made from rubber.

Related Information:

Seals and Sealing

TopHide Pictures

Grommets - Rubber - EPDM
Grommets - Rubber - EPDM

Search Rating: 89%

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

EPDM Rubber Grommets

50 +/-5 Durometer. Easy to install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Grommets - Rubber - EPDM.

Grommets - Rubber - Natural
Grommets - Rubber - Natural

Search Rating: 89%

Also see combined categories:
All Open Rubber Grommets
All Rubber Grommets

Natural Rubber Grommets

50 +/-5 Durometer. Easy to Install. Good Vibration and Shock Control. Protects Wire, Cable and Hoses. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Grommets - Rubber - Natural.

Grommets - Rubber - EPDM - Closed
Grommets - Rubber - EPDM - Closed

Search Rating: 87%

Also see combined categories:
All Closed Rubber Grommets
All Rubber Grommets

Closed EPDM Rubber Grommets

50 +/-5 Durometer. Dustproof with Approx 0.5mm thick Membrane. Easy to Install. Dust protection. Also see snap bushings for a hard plastic product serving a similar purpose.

Related Information:

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Grommets - Rubber - EPDM - Closed.

Pins Dowel

TopHide Pictures

Pins - Dowel Bushings
Pins - Dowel Bushings

Search Rating: 64%

Also see combined categories:
All Dowel Bushings

Series DB100 Spirol

Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12.


Bushings - QD and Taperlock

TopHide Pictures

Bushings - QD
Bushings - QD

Search Rating: 62%

Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing

Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley.


Bushings - Taperlock
Bushings - Taperlock

Search Rating: 62%


Bushings Spherical

TopHide Pictures

Bushings - Spherical - Plastic
Bushings - Spherical - Plastic

Search Rating: 62%

Also see combined categories:
All Spherical Bushings

Plastic spherical plain bearings. Also known as ball bushings.

Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.


Bushings - Spherical - Steel
Bushings - Spherical - Steel

Search Rating: 62%

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Bushings - Spherical - Steel - With Oil Hole
Bushings - Spherical - Steel - With Oil Hole

Search Rating: 62%

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal

Search Rating: 62%

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Bushings - Spherical - Steel - With Wiper Seal
Bushings - Spherical - Steel - With Wiper Seal

Search Rating: 62%

Also see combined categories:
All Spherical Bushings

Steel spherical plain bearings. Also known as ball bushings.

Compensates for axial loads and misalignment.


Clamping Bushings

TopHide Pictures

Bushings - Shoulder
Bushings - Shoulder

Search Rating: 62%

Mould components


Locking Bushings

TopHide Pictures

Bushings - Integral Taper
Bushings - Integral Taper

Search Rating: 62%

Also see combined categories:
All Locking Assemblies
All Locking Bushings

Stainless Steel Taper Bushings.

Will not mar shafts.


Fastening Bushings

TopHide Pictures

Bushings - Drill - Liner Type - Headless
Bushings - Drill - Liner Type - Headless

Search Rating: 62%

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Bushings - Drill - Press-fit - Headless
Bushings - Drill - Press-fit - Headless

Search Rating: 62%

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.


Bushings - Drill - Press-fit - Headless - Tungsten Carbide
Bushings - Drill - Press-fit - Headless - Tungsten Carbide

Search Rating: 62%

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Bushings - Drill - Press-fit - Standard Head
Bushings - Drill - Press-fit - Standard Head

Search Rating: 62%

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.


Bushings - Drill - Slip - With Head
Bushings - Drill - Slip - With Head

Search Rating: 62%

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point.


Tension Bushings

TopHide Pictures

Bushings - Tension
Bushings - Tension

Search Rating: 62%

Like a heavy duty roll pin.

Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and case hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications.


Stroke Rotary Bushings

TopHide Pictures

Bushings - Stroke Rotary - Miniature
Bushings - Stroke Rotary - Miniature

Search Rating: 62%

Also see combined categories:
All Stroke Rotary Bushings

2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.

Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100oC (Constant), +120oC (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.

Related Information:

Dual Vee Bearings

TopHide Pictures

Dual Vee - Adaptor Bushings
Dual Vee - Adaptor Bushings

Search Rating: 61%

Also see combined categories:
All Dual Vee Guide Wheels

Vee grooved track roller bushings.

Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned.

Related Information:

Spacers

TopHide Pictures

Spacers - Machinery Bushings
Spacers - Machinery Bushings

Search Rating: 61%

Also see combined categories:
All Round Spacers
All Flat Washers and Spacers - Metallic

Used as spacers between pulleys, gears etc

Low carbon mild steel.


Cam Followers

TopHide Pictures

Cam Followers - Self Lubricating - Bronze Bushing
Cam Followers - Self Lubricating - Bronze Bushing

Search Rating: 61%

Also see combined categories:
All Cam Followers


Locking Bushings

TopHide Pictures

Elements - Locking
Elements - Locking

Search Rating: 60%

Also see combined categories:
All Locking Assemblies

2.4 to 2200 Nm, 6-80mm Bores

ETG 100 High Strength Steel for sizes up to 55mm bore. C60 Steel for sizes over 55mm bore. Recommended machining tolerances Shaft h8, Hub H8.


Bushes Plastic

TopHide Pictures

Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Search Rating: 59%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Related Information:

Bushes - Plastic - Iglidur G - Unflanged
Bushes - Plastic - Iglidur G - Unflanged

Search Rating: 59%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.

Related Information:

Bushes - Plastic - Iglidur H - Flanged
Bushes - Plastic - Iglidur H - Flanged

Search Rating: 59%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur H - Unflanged
Bushes - Plastic - Iglidur H - Unflanged

Search Rating: 59%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Pulleys Vee

TopHide Pictures

Pulleys - Vee - A - 4L - Single Row - For QD Bushing
Pulleys - Vee - A - 4L - Single Row - For QD Bushing

Search Rating: 59%

Also see combined categories:
All Vee Pulleys A Section 12.5 and 12.7mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.

Related Information:

Pulleys - Vee - B - 5L - Single Row - For QD Bushing
Pulleys - Vee - B - 5L - Single Row - For QD Bushing

Search Rating: 59%

Also see combined categories:
All Vee Pulleys B Section 15.9 and 16.5mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.

Related Information:

Bushes Plastic

TopHide Pictures

Bushes - Plastic - Iglidur M250 - Flanged
Bushes - Plastic - Iglidur M250 - Flanged

Search Rating: 59%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.

Related Information:

Bushes - Plastic - Iglidur M250 - Unflanged
Bushes - Plastic - Iglidur M250 - Unflanged

Search Rating: 59%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.

Related Information:

Bushes - Plastic - Iglidur P - Flanged
Bushes - Plastic - Iglidur P - Flanged

Search Rating: 59%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur P - Unflanged
Bushes - Plastic - Iglidur P - Unflanged

Search Rating: 59%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur J - Flanged
Bushes - Plastic - Iglidur J - Flanged

Search Rating: 59%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur J - Unflanged
Bushes - Plastic - Iglidur J - Unflanged

Search Rating: 59%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur Q - Flanged
Bushes - Plastic - Iglidur Q - Flanged

Search Rating: 58%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur Q - Unflanged
Bushes - Plastic - Iglidur Q - Unflanged

Search Rating: 58%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Plungers Ball

TopHide Pictures

Ball Buttons
Ball Buttons

Search Rating: 58%

Also known as striker bushings or ball plunger detents. Use with ball or bolt spring plungers for a hard wearing contact area.

Burnished ground hardened steel.


Bushes Plastic

TopHide Pictures

Bushes - Plastic - Iglidur F - Flanged
Bushes - Plastic - Iglidur F - Flanged

Search Rating: 58%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur F - Unflanged
Bushes - Plastic - Iglidur F - Unflanged

Search Rating: 58%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Search Rating: 58%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Search Rating: 58%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerances is E10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur Z - Flanged
Bushes - Plastic - Iglidur Z - Flanged

Search Rating: 58%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur Z - Unflanged
Bushes - Plastic - Iglidur Z - Unflanged

Search Rating: 58%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur H370 - Flanged
Bushes - Plastic - Iglidur H370 - Flanged

Search Rating: 57%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur H370 - Unflanged
Bushes - Plastic - Iglidur H370 - Unflanged

Search Rating: 57%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur A200 - Flanged
Bushes - Plastic - Iglidur A200 - Flanged

Search Rating: 57%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur A200 - Unflanged
Bushes - Plastic - Iglidur A200 - Unflanged

Search Rating: 57%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur A290 - Flanged
Bushes - Plastic - Iglidur A290 - Flanged

Search Rating: 57%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur A290 - Unflanged
Bushes - Plastic - Iglidur A290 - Unflanged

Search Rating: 57%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerances is D11 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur X - Flanged
Bushes - Plastic - Iglidur X - Flanged

Search Rating: 57%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Bushes - Plastic - Iglidur X - Unflanged
Bushes - Plastic - Iglidur X - Unflanged

Search Rating: 57%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerances is F10 after H7 Pressfit. Tolerances listed in the tables take this into account.


Latches Draw

TopHide Pictures

Latches - Draw - Soft
Latches - Draw - Soft

Search Rating: 54%

Tolerates misalignment. UV resistant thermoplastic elastomer body. Glass reinforced nylon link and bushings. Stainless steel rivet, pins, keeper and brackets. Cushions impact and absorbs vibration.

Keeper included.


Latches Other

TopHide Pictures

Latches - Swell
Latches - Swell

Search Rating: 50%

Latches in any frame thickness, blind application, glass or plastic. Latches accommodate misalignment between door and frame.

Black nylon handle and nut. Black rubber bushing provides sound deadening effect. When handle is lifted bushing diameter decreases allowing it to pass through the hole in the frame to unlatch the door.


Tooling Balls

TopHide Pictures

Balls - Tooling - Two Piece - Construction - Steel
Balls - Tooling - Two Piece - Construction - Steel

Search Rating: 50%

Also see combined categories:
All Tooling Balls
All Standard Tooling Balls

High quality tooling balls provide a precise reference point for critical machining operations.

Ball and shank are concentric within 5 microns (0.0002 in.) TIR. 1144 steel heat treated to 53-57 RC. Precise shoulder base to ball centre line dimension within +/- 0.00508mm. Weld between ball and shank is designed so the ball will fall off if subject to unusually heavy lateral force, preventing set up and inspection errors that may occur because of a bent shaft. Construction balls can be pulled into a hole or bushing from below without applying pressure on the ball by using a cap screw in the internally tapped shank.


Housings with Bearing

TopHide Pictures

Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing
Housings - Bearing - Pillow Block - Thermoplastic with Stainless Bearing

Search Rating: 48%

Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.


Housings - Bearing - 3 Bolt Offset - Thermoplastic with Stainless Bearing
Housings - Bearing - 3 Bolt Offset - Thermoplastic with Stainless Bearing

Search Rating: 48%

Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.


Housings - Bearing - 4 Bolt Flange - Thermoplastic with Stainless Bearing
Housings - Bearing - 4 Bolt Flange - Thermoplastic with Stainless Bearing

Search Rating: 48%

Thermoplastic housed units offer an economical alternative with good chemical and washdown resistance.

Food grade. Thermoplastic housings are off-white and are made from glass reinforced PBT resin. Excellent mechanical, thermal and electrical properties. Operational temperature -20 to +100 oC. Bearings are 440C stainless steel. Bushings and grease fittings are 300 grade stainless steel.


Linear Bearings

TopHide Pictures

Bearings - Linear - Sliding - Stainless - PTFE - Closed
Bearings - Linear - Sliding - Stainless - PTFE - Closed

Search Rating: 47%

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.


Bearings - Linear - Sliding - Stainless - PTFE - Open
Bearings - Linear - Sliding - Stainless - PTFE - Open

Search Rating: 47%

Also see combined categories:
All Sliding Linear Bearings

Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.

Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.


Latches Handle

TopHide Pictures

Handles - Latching - 2-Point Locking Rod Kit
Handles - Latching - 2-Point Locking Rod Kit

Search Rating: 43%

Kit can be used with any 5/16in. Square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers and three set screws.



Show all items starting with
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   1   2   3   4   5   6   7   8   9  





Other Store Pages

Click Page Banner Below

Top

Main Pages

Click Page Banner Below

Top





Top



Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 124193 products in 3084 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts and Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.