Small Parts & Bearings - an MBA company

Shafting pre drilled and tapped high carbon steel categories


Shafting Precision Ground


Shafting - Pre Drilled and Tapped - Stainless Steel
Shafting - Pre Drilled and Tapped - Stainless Steel

Also see combined categories:
All Shafting
All Stainless Shafting

For use with rail supports and open linear bearings

This category may be available in the new MBA online store at Shafting - Pre Drilled and Tapped - Stainless Steel.


Rod - Drill Blanks
Rod - Drill Blanks

Also see combined categories:
All Silver Steel Drill Blanks
All Drill Rod

Made of hardened high speed steel.

Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc. This category may be available in the new MBA online store at Rod - Drill Blanks.


Rod - Drill - A-2 Air Hardening
Rod - Drill - A-2 Air Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening. Maximum abrasion resistance. 65 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for A-2 hardening requirements. This category may be available in the new MBA online store at Rod - Drill - A-2 Air Hardening.


Rod - Drill - O-1 Oil Hardening
Rod - Drill - O-1 Oil Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

For general toolroom use. Good non-deforming characteristics. Moderate resistance to abrasion. 90 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for O-1 hardening requirements. This category may be available in the new MBA online store at Rod - Drill - O-1 Oil Hardening.


Rod - Drill - S-7 Air Hardening
Rod - Drill - S-7 Air Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

Air hardening molybdenum, chromium, shock resisting. High impact strength with moderate wear resistance. 95 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for S-7 hardening requirements. This category may be available in the new MBA online store at Rod - Drill - S-7 Air Hardening.


Rod - Drill - Silversteel - W-1 Water Hardening
Rod - Drill - Silversteel  - W-1 Water Hardening

Also see combined categories:
All Metal Bar - Silver Steel and Drill Rod
All Drill Rod

For punches dies and high strength machine parts. Unhardened - requires heat treatment.

High abrasion resistance and high toughness when hardened. 100 percent machinability. Requires heat treating to harden. Small diameters may not be perfectly straight. Refer engineering guides online for W-1 hardening requirements. This category may be available in the new MBA online store at Rod - Drill - Silversteel - W-1 Water Hardening.


Shafts - Idler
Shafts - Idler


Ready made precision ground idler shafts.

Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design. This category may be available in the new MBA online store at Shafts - Idler.

Related Information:


Inserts - Expansion - Press In - Brass
Inserts - Expansion - Press In - Brass

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.


Inserts - Expansion - Press In - Brass - Flanged
Inserts - Expansion - Press In - Brass - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.


Inserts - Expansion - Press In - 303 Stainless - Flanged
Inserts - Expansion - Press In - 303 Stainless - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.


Inserts - Expansion - Press In - 303 Stainless Steel
Inserts - Expansion - Press In - 303 Stainless Steel

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : 303 Stainless Steel. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.


Bumpers - Square and Rectangular - Steel Plated - Neoprene
Bumpers - Square and Rectangular - Steel Plated - Neoprene

Also see combined categories:
All Square Bumpers
All Bumpers

With drilled and counterbored holes for mounting. Neoprene bonded to steel plate.

This category may be available in the new MBA online store at Bumpers - Square and Rectangular - Steel Plated - Neoprene.


Bumpers - Square and Rectangular
Bumpers - Square and Rectangular

Also see combined categories:
All Square Bumpers
All Bumpers

With drilled and counterbored holes for mounting. Neoprene only, no steel plate.

This category may be available in the new MBA online store at Bumpers - Square and Rectangular.


Shafting - Aluminium - Ceramic Coated - Tapped
Shafting - Aluminium - Ceramic Coated - Tapped

Also see combined categories:
All Shafting
All Aluminium Shafting

Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.

Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at Shafting - Aluminium - Ceramic Coated - Tapped.

Related Information:


Bumpers - Square and Rectangular - Steel Plated - Urethane
Bumpers - Square and Rectangular - Steel Plated - Urethane

Also see combined categories:
All Square Bumpers
All Bumpers

With drilled and counterbored holes for mounting. Urethane bonded to steel plate.

This category may be available in the new MBA online store at Bumpers - Square and Rectangular - Steel Plated - Urethane.


Magnets - Ceramic - 3 Pole - Insulated Aluminium - Tapped Blind Hole
Magnets - Ceramic - 3 Pole - Insulated Aluminium - Tapped Blind Hole

Also see combined categories:
All Magnets
All Ceramic Magnets

Extended poles can be lightly machined. With tapped blind hole in base for mounting. Insulated aluminium casing.

Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.


Shafting - Ground - Precision - Chrome Plated
Shafting - Ground - Precision - Chrome Plated


Precision ground shafting. AISI C1060 and chrome plated for corrosion resistance. Case hardened and recommended for use with precision bearings. Ends are not plated.

Case hardened to 60-65 Rockwell C. Chrome plated for corrosion resistance. This category may be available in the new MBA online store at Shafting - Ground - Precision - Chrome Plated.


Shafting - Ground - Precision - High Carbon Steel
Shafting - Ground - Precision - High Carbon Steel

Also see combined categories:
All Shafting
All Steel Shafting

Precision ground shafting. AISI C1060. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - High Carbon Steel.

Related Information:


Shafting - Ground - Precision - Stainless 303 Grade
Shafting - Ground - Precision - Stainless 303 Grade

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting.

This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 303 Grade.

Related Information:


Shafting - Ground - Precision - Stainless 416 Grade Hardened
Shafting - Ground - Precision - Stainless 416 Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 416 grade. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 416 Grade Hardened.

Related Information:


Shafting - Ground - Precision - Stainless 420 Grade Hardened
Shafting - Ground - Precision - Stainless 420 Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 420 grade. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 420 Grade Hardened.

Related Information:


Shafting - Ground - Precision - Stainless 440C Grade Hardened
Shafting - Ground - Precision - Stainless 440C Grade Hardened

Also see combined categories:
All Shafting
All Stainless Shafting

Precision ground shafting. 440C grade. Hardened and recommended for use with precision bearings.

This category may be available in the new MBA online store at Shafting - Ground - Precision - Stainless 440C Grade Hardened.

Related Information:


Shafting - Ground - Precision - Titanium - High Strength
Shafting - Ground - Precision - Titanium - High Strength

Also see combined categories:
All Shafting
All Titanium Shafting

Titanium shafting available in oversized and undersized tolerances

Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5, 6Al-4V, TC4 is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. Shaft with undersized tolerances is suitable for use with precision ground bearings wih inner rings. HRC 36. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.

Related Information:


Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1
Shafting - Ground - Precision - Titanium - Ti-Gr2-TA1

Also see combined categories:
All Shafting
All Titanium Shafting

CP2 Commercially Pure Titanium Grade 2. Tensile Strength 35.2 kgf/mm2. Yield Strength 28.2 kgf/mm2. Elongation 20 Percent.

Commercially pure for general industrial corrosion applications. UNS R50400. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.3, O 0.25, Ti Balance. Shaft with undersized tolerances is suitable for use with precision ground bearings with inner rings. HRB 74. Surface Finish Ra 0.8-1.6 um. Not suitable for running needle bearings directly. Shaft with oversized tolerances is suitable for pulleys or gears requiring interference fits, or for machining to your required tolerances.

Related Information:


Shafts - Pinion
Shafts - Pinion


This category may be available in the new MBA online store at Shafts - Pinion.


Rail Supports - Without Shaft
Rail Supports - Without Shaft

Also see combined categories:
All Shaft Supports

For mounting of linear shafting.

Shafting sold separately. Support is made from aluminium. This category may be available in the new MBA online store at Rail Supports - Without Shaft.

Related Information:


Rail Supports - With Shaft
Rail Supports - With Shaft

Also see combined categories:
All Shaft Supports

Includes linear shafting.

Includes shaft to h6 tolerances. Support is made from aluminium. This category may be available in the new MBA online store at Rail Supports - With Shaft.

Related Information:


Supports - Pedestal Two Bolt
Supports - Pedestal Two Bolt

Also see combined categories:
All Supports

For linear shafting.

Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel. This category may be available in the new MBA online store at Supports - Pedestal Two Bolt.

Related Information:


Screws - Self Drilling - Pan Head
Screws - Self Drilling - Pan Head

Also see combined categories:
All Self Drilling Screws

Zinc chromate fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.

This category may be available in the new MBA online store at Screws - Self Drilling - Pan Head.


Rail Supports - With Shaft - One Piece
Rail Supports - With Shaft - One Piece

Also see combined categories:
All Shaft Supports

One piece construction made from 6061-T6 Aluminium with ceramic coating to Mil-8625. Suitable for use with Frelon lined linear bearings.

Not suitable for linear ball bearings. Weld spatter, paints and other contaminants will not stick to the shaft. Vibration resistant and non-magnetic. Not suitable for harsh washdown environments. This category may be available in the new MBA online store at Rail Supports - With Shaft - One Piece.

Related Information:


Screws - Self Drilling - Hex Washer Head
Screws - Self Drilling - Hex Washer Head

Also see combined categories:
All Self Drilling Screws

Zinc chromate. Fluted point. Used for fastening sheet metal to wood or metal. Drills, taps and fastens in one application.

This category may be available in the new MBA online store at Screws - Self Drilling - Hex Washer Head.


Magnets - Ceramic - 2 Pole - Insulated Aluminium - Press Fit
Magnets - Ceramic - 2 Pole - Insulated Aluminium - Press Fit

Also see combined categories:
All Magnets
All Ceramic Magnets

Extended poles can be lightly machined. Press fit. Insulated aluminium casing.

Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.


Magnets - Ceramic Blocks
Magnets - Ceramic Blocks

Also see combined categories:
All Magnets
All Ceramic Magnets

Low cost, light weight, high energy material

Non conductive hard brittle material. Performs best at temperatures below 249 oC. Can be cut with a diamond wheel. Difficult to grind and can't be machined or drilled by normal methods. Tolerance 0.13mm on all dimensions.


Shafting - Linear - Square
Shafting - Linear - Square


This category may be available in the new MBA online store at Shafting - Linear - Square.


Shafting - Aluminium - Ceramic Coated
Shafting - Aluminium - Ceramic Coated

Also see combined categories:
All Shafting
All Aluminium Shafting

Recommended for use with Frelon Gold linear bearings. Aluminium 6061-T6 with ceramic coated finish. Ceramic coat has rockwell hardness of 70C. No magnetic and vibration reseistant.

Weld spatter, contaminants and paints will not stick. Do not use with ball bearings. Use with Frelon lined or similar plain bearings only. Shaft ends are not coated. This category may be available in the new MBA online store at Shafting - Aluminium - Ceramic Coated.

Related Information:


Shafting - Carbon Steel - Keyed
Shafting - Carbon Steel - Keyed

Also see combined categories:
All Shafting
All Steel Shafting

Keyways are cut full length of each bar. Low carbon steel C1018. Good case hardening properties.

Diameter Tolerance +0.00/-0.051. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00. Unhardened carbon steel. Special order may be available for stainless steel, other diameters, other lengths. Please ask.


Pins - Groove
Pins - Groove

Also see combined categories:
All Groove Pins

Non threaded press fit fastener that doesn't require a reamed hole as do dowel pins.Commonly used in place of taper pins.

An economic method of fastening without the need for precision drilled and reamed holes. Recommended hole tolerance is H11. Total length may be slightly longer than the nominal length. Expanded portion of the pin is compressed into the hole a few thousands of an inch wider than the nominal pin diameter. Radial forces lock the pin securely into the drilled hole. This category may be available in the new MBA online store at Pins - Groove.

Related Information:


Shafts - Flexible - Panel Mount - Cased
Shafts - Flexible - Panel Mount - Cased

Also see combined categories:
All Flexible Panel Mount Shaft

This category may be available in the new MBA online store at Shafts - Flexible - Panel Mount - Cased.


Shafts - Flexible - Panel Mount - Open
Shafts - Flexible - Panel Mount - Open

Also see combined categories:
All Flexible Panel Mount Shaft

This category may be available in the new MBA online store at Shafts - Flexible - Panel Mount - Open.


Shafts - Flexible - Coupling Ends - Open - Mild Steel
Shafts - Flexible - Coupling Ends - Open - Mild Steel

Also see combined categories:
All Coupling End Flexible Shaft

Flexible shafting with coupling ends ready to attach to a fixed shaft.

1.7 and 2.5mm cable diameters can be operated manually at 62mm bend radius with torsional break strength of 0.62 N.m. 3.3F shaft has a greater degree of flexibility than standard 3.3mm. 3.3F shaft can be used in dynamic mode if shaft isshortened to approximately 50mm. This category may be available in the new MBA online store at Shafts - Flexible - Coupling Ends - Open - Mild Steel.

Related Information:


Housings - Linear - Square
Housings - Linear - Square

Also see combined categories:
All Linear Bearing Housings

Used to maintain radial integrity and eliminate the need for parallel shafting.

Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads. This category may be available in the new MBA online store at Housings - Linear - Square.


Bungs and Caps - Reversible - Round
Bungs and Caps - Reversible - Round


Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.

Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges. This category may be available in the new MBA online store at Bungs and Caps - Reversible - Round.

Related Information:


Bushings - Drill - Press-fit - Headless
Bushings - Drill - Press-fit - Headless

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Press-fit - Headless.


Bushings - Drill - Press-fit - Headless - Tungsten Carbide
Bushings - Drill - Press-fit - Headless - Tungsten Carbide

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig.

Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating a precise location point. Hardness: RC 67-69. This category may be available in the new MBA online store at Bushings - Drill - Press-fit - Headless - Tungsten Carbide.


Bushings - Drill - Press-fit - Standard Head
Bushings - Drill - Press-fit - Standard Head

Also see combined categories:
All Drill Bushings

Designed to guide, position, and support the cutting tool in a metalworking jig. Hardened steel.

Hardness: RC 62-64. This category may be available in the new MBA online store at Bushings - Drill - Press-fit - Standard Head.


Inserts - Self Tapping - For Aluminium - Steel
Inserts - Self Tapping - For Aluminium - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.

Related Information:


Inserts - Self Tapping - For Plastics - Steel
Inserts - Self Tapping - For Plastics - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.

Related Information:


Inserts - Self Tapping - For Aluminium - Stainless 303
Inserts - Self Tapping - For Aluminium - Stainless 303

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.

Related Information:


Inserts - Self Tapping - For Aluminium - Stainless 316
Inserts - Self Tapping - For Aluminium - Stainless 316

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or hard plastics. Made from 316 stainless steel.

Related Information:


Inserts - Self Tapping - For Plastics - Stainless Steel
Inserts - Self Tapping - For Plastics - Stainless Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.

Related Information:





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Dental Bearings Disc Springs PDF Dowel Pins PDF Dowel Pins Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138615 products in 2015 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)

Small Parts & Bearings offers 138615 products in 2015 categories including couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.