Shaft - Small Parts Engineering Product Catalogue

Categories that include the term: SHAFT RELEVANCE ****VERY HIGH**** 100% All search words found in headers or categories Bearings - Idler Rollers Rollers - Idler - Ribbed - With Shaft Rollers - Idler - Solid - With Shaft Bushings - Splined Splined Shafts Match with same size internal splined bushes. Clamp Style Shaft Collars Collars - Shaft - Clamp Type Clamps - Shaft Clamps - Shaft Mild Steel: 045M10. Stainless Steel: 303S21. Clutch Couplings Couplings - Clutch - Shaft Mounted 0.565 to 14 N.m. For in-line loads. Clutches - Shaft Mounted Clutches - Shaft Mounted 24 V DC - Zero Backlash Armature - For parallel loads. This basic information is designed to assist you to make a decision on which clutch to use. Full dimensions available on request. Clutches - Slip Clutches - Slip - Magnetic Particle - Integral Shaft - No Power Requires no power. Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page. Collars - Shaft Collars - Shaft - D-Bore Collars - Shaft - Fairloc Collars - Shaft - Gripfast Self Locking - Quick Release. 265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs. Collars - Shaft - Hinged Type Precision machined. Convenient easy-to-assemble design. Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs. Collars - Shaft - Standard Includes miniature precision types. Carbon steel, 303 and 316 stainless. Collars - Shaft - Stroke Adjustment Recommended tolerances for mating shaft diameter : h6. Use with rubber washers listed under WASHERS. Collars - Shaft - With Integral Shim Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances. Couplings - Flexible-Shaft Shafts - Flexible - Coupling Ends - Cased Shafts - Flexible - Coupling Ends - Open (SDP) Flexible shafting with coupling ends ready to attach to a fixed shaft. Shafts - Flexible - Panel Mount - Cased Shafts - Flexible - Panel Mount - Open Drives - Gear Gearboxes - Output Shafts For use in Cross Axis gearboxes with bores. P and PF Series. Drylin® Shafts and Bearings Drylin Sliding Bearings Linear sliding motion. Drylin Sliding Film Linear sliding motion. Housings - Igubal - Sliding Shafting - Aluminium Drylin aluminium shafting is recommended for use with Igubal Drylin bearings only. Extenders - Shaft Extenders - Shaft Miniature and large shaft extenders. Flexible Couplings Shafts - Flexible - Coupling Ends - Open (Ondrives) Flexible Shafts Couplings - Flexible-Shaft Type Nonmagnetic flexible shaft couplings. Max torque 0.39 Nm. Gears - Pinion Shafts - Pinion Hollow Shafts Bearings - Needle Roller - Inner Rings Hardened sleeves for needle roller bearings. Shafting - Pipe - AISI52100 Steel Tube - Hexagonal - Brass Tube - Rectangular - Brass Tube - Round - Aluminium For general hobby applications. Tube - Round - Brass For general hobby applications. Includes 6.6mm Streamline Tube. Tube - Round - Bronze - 954 Aluminium Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Tube - Round - Bronze - LG2 (Standard) Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Tube - Round - Bronze - Phosphor Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Tube - Round - Copper For general hobby applications. Tube - Round - Sintered Bronze Oil impregnated sintered bronze tube - self lubricating. Tube - Round - Stainless Steel For general hobby applications. Tube - Square - Brass Integral Shaft Gears Gears - Spur - Module 0.50 - Stem Gears with integral shafts. Gears - Spur - Module 0.75 - Stem Gears with integral shafts. Gears - Spur - Module 0.80 - Stem Gears with integral shafts. Gears - Spur - Module 1.00 - Stem Gears with integral shafts. Gears - Spur - Module 1.50 - Stem Gears with integral shafts. Gears - Spur - Module 2.00 - Stem Gears with integral shafts. Gears - Spur - Module 2.50 - Stem Gears with integral shafts. Gears - Spur - Module 3.00 - Stem Gears with integral shafts. Linear Ball Splines Linear Ball Splines - Shaft Use with either flanged or unflanged Linear Ball Spline Bearings. Linear Shaft Supports Shafting - Pre Drilled for Rail Supports Shafting - Rail Supports - With Shaft Includes shaft. Shafting - Rail Supports - Without Shaft For mounting of shafting. Shafting - Supports - Flanged Four Bolt For linear shafting. Shafting - Supports - Flanged Two Bolt For linear shafting. Shafting - Supports - Pedestal Two Bolt For linear shafting. Locks - Shaft Shaft Locks - Potentiometer Reducers - Shaft Reducers - Bore Inch to Metric / Inch to Inch / Metric to Metric. Rigid Shaft Couplings Couplings - Rigid 0.35 to 5.1 Nm. Rollers - Idler - Without Shaft Rollers - Idler - Stainless Steel Shaft Assortments - 3mm Dia Assortment Kits - Various Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins Shaft Couplings Couplings - Ball High Speed - Up to 15 Degrees Angular Offset. 0.17 to 22.6 N.m Torque. Up to 20,000 rpm. Couplings - Bantam - Components Isolates vibration up to 85%. Sleeve provides electrical insulation. 0.21Nm at 1725rpm. Couplings - Bellows Zero Backlash - Constant Velocity Ratio - Low Inertia. 0.85 to 2.0 Nm. 2000 to 20,000rpm. Couplings - Bellows - Hiflex Precise adjustment - Vibration resistance - Large misalignment capability. 0.01 to 9.17 Nm. 2000 rpm. Couplings - BoWex - Junior Nylon 2 piece and 3 piece couplings. 5 to 24 Nm. 6000 rpm max. Couplings - Clutch - Flange Mounted 0.565 to 14 N.m. For in-line loads. Couplings - Control Flex. 0.45 to 6.44 Nm. Couplings - Cross Joint. 0.5 to 10 N.m. 3600 to 6000 rpm. Couplings - Double Disk. 0.7 to 12.5 Nm. 3000 to 19000 rpm. Zero Backlash - High Torsional Stiffness. Couplings - Geargrip 0.67 to 6.78 Nm. Max speed 3000 rpm. Couplings - Helical - Standard 0.1 to 16.2 Nm. Couplings - Jaw Type - With Rubber Spider Max 3600 RPM. 0.39 to 16.27 Nm. Couplings - K Type Up to 3600 RPM - Minus 20 to Plus 60 Degrees C. 0.34 to 18 Nm. Couplings - Neo-Flex 0.71 to 1.27 Nm. Couplings - Oldham - Complete 0.06 to 44 Nm. Max Speed: 3000 RPM. Couplings - Single Disk 0.7 to 19 Nm. 2400 to 10000 rpm. Couplings - Sleeve Type 0.05 to 2.1 Nm. Max Speed 1750 rpm. Couplings - Slip - Spring Wrapped Tension control - transmission overload protection. 0.035 to 1.69 Nm. Couplings - Slit Type Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm. Couplings - Spider Type 2.1 to 17 Nm. Couplings - Spline Type 0.5 to 4.5 Nm. 12000 to 24000 rpm. Couplings - Spring 1.4 Nm Max Torque. Couplings - Torque Tube Internal compression spring preloads the ends against axial movement and backlash. Up to 2.8 Nm. Up to 2000 rpm. Couplings - Uniflex High speed to 30000 rpm. 2.3 to 9.27 Nm. Shaft Spacers Sleeves - Hex Hole Sleeves - Square Hole - Plain Spacers - Hex - Threaded - Nylon Threaded Hex Spacers. Spacers - Round - Through Bore - Aluminium Shaft spacers - Aluminium Spacers - Square - Threaded Threaded spacers. Standoffs - Hexagonal Swage Type - Threaded - Brass or Stainless Steel. Standoffs - Round Swage Type - Threaded - Brass or Stainless Steel. Washers - Flat - Commercial - All Types Includes all materials listed in other commercial washer categories. Shaft Supports Shafting - Supports - Block For linear shafting. Material: Aluminium. Shafts Rod - Drill For punches dies and high strength machine parts. Unhardened - requires heat treatment. Shafting - Ground Precision ground shafting. Various materials including silver steel, 303 304 316 416 stainless steel, hardened carbon steel, chrome vanadium alloy. Splined Shafts and Bushes Splined Bushes - Unflanged Match with same size External splined shafts. Match bushes and shafts by Major Diameter. RELEVANCE ****HIGH**** All search words found in header - some within other words Hobby Shafting Hobby Shafting - Precision Ground A small selection of popular sizes. See main listings for sizes not shown here. Shafting Rod - Round - Acetal Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger. Rod - Round - Aluminium For general hobby applications. Rod - Round - Brass For general hobby applications. Rod - Round - Bronze - 686 Manganese Sizes listed are FINISHED SIZE. Product supplied will be larger. Rod - Round - Bronze - 954 Aluminium Sizes listed are FINISHED SIZE. Product supplied will be larger. Rod - Round - Bronze - LG2 (Standard) Sizes listed are FINISHED SIZE. Product supplied will be larger. Rod - Round - Bronze - PB1 Sizes listed are FINISHED SIZE. Product supplied will be larger. Rod - Round - Nylon High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger. Rod - Round - Polyester PETP High mechanical strength, stiffness and hardness. Sizes listed are FINISHED SIZE. Product supplied will be larger. Rod - Round - PTFE Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger. Rod - Round - Sintered Bronze Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown. Rod - Round - Stainless Steel For general hobby applications. Rod - Round - Urethane Shafting - Pipe - Aluminium Shafting - Pipe - Aluminium Recommended for use with Igubal Drylin bearings only. Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2 Shafting - Supported Shafting - Supported - Pre-Drilled - Aluminium For Drylin Bearings. Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2 Shaftloc-tm- Shaftloc-tm Clamp Type A Simple effective component clamping Passivated 416 Stainless Steel Simple two part screw together system clamps parts securely together. Vibration resistant. Employing a special asymetric thread to self-lock when the nut encounters resistance. The nut turns freely until it contacts the parts being clamped together. Additional turns wedge the parts into a locked and vibration resistant condition. Shaftloc-tm Simple Type M Simple effective way to lock components onto shafts. Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve. Shaftloc-tm Sleeves - Double Ended Simple effective way to lock components onto shafts. 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Shaftloc-tm Sleeves - Single Ended Simple effective way to lock components onto shafts. 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened RELEVANCE ****HIGH**** All search words found in category name - some within other words RELEVANCE **LOW** All search words found in category description Actuators - Leadscrew Actuator - Leadscrew - High Duty VHD Leadscrew: Teflon coated Stainless Steel. Anti-Backlash Nut: Self-lubricating Polyacetal. Base, Carriage & Rail Supports: Aluminium. Shafts & Bearings: Hardened Steel. Weight: 12kg. Actuator - Leadscrew - Light Duty ZBX Leadscrew: Teflon coated Stainless Steel. Anti-Backlash Nut: Self-lubricating Polyacetal. Base, Carriage & Rail Supports: Anodised Aluminium. Shafts & Bearings: Hardened Steel. Weight: 1.3kg. Actuator - Leadscrew - Medium Duty ZBX Leadscrew: Teflon coated Stainless Steel. Anti-Backlash Nut: Self-lubricating Polyacetal. Base, Carriage & Rail Supports: Anodised Aluminium. Shafts & Bearings: Hardened Steel. Weight: 3kg. Adjustable Linear Bearings Bearings - Linear - Ball Adjustable and fixed types - open for running on a supported rail and closed for fixed shafts. Assemblies - Locking Assemblies - Locking - Flanged Suitable for locking sprockets, pulleys, eccentric shafts. Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. Flange eliminates axial movement of secured component. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub. Assemblies - Locking - Unflanged Suitable for locking sprockets, pulleys, eccentric shafts. Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub. Ball Bushings - Thomson Bearings - Linear - Ball - Thomson Precision Steel (Closed) For running on shafts fixed at the ends. Bearings - Linear - Ball - Thomson Precision Steel (Open) For running on shafts supported by a rail along their length. Bearings - Linear - Ball - Thomson Super (Closed) For running on shafts fixed at the ends. Bearings - Linear - Ball - Thomson Super (Open) For running on shafts supported by a rail along their length. Bearings - Linear - Ball - Thomson Super Smart (Closed) For running on shafts fixed at the ends. Bearings - Linear - Ball - Thomson Super Smart (Open) For running on shafts supported by a rail along their length. Bearings - Clutch Bearings - One Way - Roller Roller Clutch Bearings rotate in one direction only. Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm. Bearings - Hydrodynamic Bearings - Hydrodynamic Pressure Alternative to ball bearings - quiet operation - patented design. Applications include compact fan motors, copy machines, printers, laptop computers, cameras and toys. Stainless Steel casing and shield - Long Life. Use with Case Hardened shafting 2um surface finish -0.007/-0.012 for normal use. Use with Case Hardened shafting 1um surface finish -0.005/-0.007 for high accuracy use. 30% weight savings over ball bearings. Bearings - Linear Bearings - Linear - Ball - Miniature - High Precision High Precision Corrosion Resistant Miniature Linear Bearings. High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm. Bearings - Press Bearings - Press - Acetal - Flange Mounted Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish. Bearings - Press - Needle Roller - Flange Mounted Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer. Bearings - Press - Sintered Bronze Self lubricating. -28 to +95 Deg C. Use any shaft material with 0.8 um or finer finish. Self aligning +/- 5 Degress. Bearings - Press - Sintered Bronze - Flange Mounted Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish. Brakes - Magnetic Brakes - Magnetic - Particle Zero Backlash - Low Inertia - No Friction Surface. 24 V DC. Shaft becomes coupled to housing with electrical excitation. Torque is proportional to the DC input current. Bushes - Bronze Bushes - Bronze - Sintered - Flanged - Oilite Genuine Oilite flanged oil impregnated sintered bronze bushes. Genuine Oilite Sintered Bronze designed to be fitted in H7 housings and f7 shafts Static Load: 50N per mm Sq Dynamic Load: 15N per mm sq Rec Speed Range: 0.3 mtr per second to 0.5 mtr per second Limit one Pv factor no greater than 1.8 Pv (Pv= N per mm sq x mtr per second) Bushes - Bronze - Sintered - Unflanged - Oilite Genuine Oilite oil impregnated sintered bronze bushes. Genuine Oilite Sintered Bronze designed to be fitted in H7 housings and f7 shafts Static Load: 50N per mm Sq Dynamic Load: 15N per mm sq Rec Speed Range: 0.3 mtr per second to 0.5 mtr per second Limit one Pv factor no greater than 1.8 Pv (Pv= N per mm sq x mtr per second) Bushings - Integral Taper Bushings - Integral Taper Stainless Steel Taper Bushings. Will not mar shafts. Bushings - Locking Hub Bushings - Locking Hub Friction grip construction. Connects rotating components to shafts. Transmits high torque without keyways. Two styles - see diagrams. Bushings - Stroke Rotary Bushings - Stroke Rotary - Miniature 2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time. Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100°C (Constant), +120°C (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload. Bushings - Stroke Rotary - Sealed Stroke Rotary Bushing series can operate in both linear and rotary directions at the same time. Material: Carbon Steel. The fit of Stroke Rotary Bushing with shaft and housing is recommend as shown in Table 1 of the diagram. Actual Stroke Length should be less than 80% of max. stroke. Mating Shafts should be HRC58-64. Surface roughness 0.85 or better. Oil holes provided for lubrication. Circlips - External - Special Circlips - External - Grooveless Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring. Clamps - Gear Clamps - Gear - Two Piece - Commercial Balanced Commercial - Stainless - Aluminium - Carbon Steel - For our clamp type gears. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. These clamps are designed to clamp the OD of the hub on our clamp type gears. The shaft size listed is for reference only. Clamps - Gear - Two Piece - Precision Balanced Precision - Stainless - Aluminium - Carbon Steel - For our clamp type gears. Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. These clamps are designed to clamp the OD of the hub on our clamp type gears. The shaft size listed is for reference only. Clutch Brakes Clutch Brakes - Magnetic - Bu-Ord Size 11 Breakaway Torque (Energised) at 24-28 V DC : 10.8g.cm (0.15 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 3.6g.cm (0.05 oz.in). Shafts A & B coupled when energised, B shaft braked when de-energised. Inertia (De-Energised) at 24-28 VDC : 2.38g.cm sq (0.013 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.3g.cm sq (0.029 oz.in sq). Clutch Brakes - Magnetic - Bu-Ord Size 11 - Reverse Acting Breakaway Torque (Energised) at 24-28 V DC : 18g.cm (0.25 oz.in). Breakaway Torque (De-energised) at 24-28 V DC : 7.2g.cm (0.10 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 7.4g.cm sq (0.041 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.1g.cm sq (0.028 oz.in sq). Clutch Brakes - Magnetic - Bu-Ord Size 18 Breakaway Torque (Energised) at 24-28 V DC : 14.4g.cm (0.20 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 2.2g.cm (0.03 oz.in). Shafts A & B coupled when energised, B shaft braked when de-energised. Inertia (Energised) at 24-28 VDC : 5.11g.cm sq (0.071 oz.in sq). Inertia (Energised) at 24-28 VDC : 7.56g.cm sq (0.105 oz.in sq). Clutch Brakes - Magnetic - Bu-Ord Size 18 - Reverse Acting Breakaway Torque (Energised) at 24-28 V DC : 3.6g.cm (0.05 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 14.4g.cm (0.2 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 7.27g.cm sq (0.101 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.11g.cm sq (0.071 oz.in sq). Clutches - Friction Clutches - Friction - Slip Ease ADJUSTABLE TORQUE - For shaft to shaft coupling. Set screw housings in both housing and cartridge. SLIP-EASE utilises an axial loaded multi-plate design. For applications where space is at a premium and low backlash is required. Backlash of 2° as standard. Clutches - Magnetic Clutches - Magnetic - Bu-Ord Size 11 Breakaway Torque (Energised) at 24-28 V DC : 10.8g.cm (0.15 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 3.6g.cm (0.05 oz.in). Shafts A & B coupled when energised, braked when de-energised. Inertia (De-Energised) at 24-28 VDC : 0.94g.cm sq (0.013 oz.in sq). Inertia (Energised) at 24-28 VDC : 2.09g.cm sq (0.029 oz.in sq). Clutches - Magnetic - Bu-Ord Size 11 - Reverse Acting Breakaway Torque (Energised) at 24-28 V DC : 18g.cm (0.25 oz.in). Breakaway Torque (De-energised) at 24-28 V DC : 7.2g.cm (0.10 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 7.4g.cm sq (0.041 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.0g.cm sq (0.028 oz.in sq). Clutches - Magnetic - Bu-Ord Size 11 - Triplex Breakaway Torque (Energised) at 24-28 V DC : 14.4g.cm (0.20 oz.in). Breakaway Torque (De-energised) at 24-28 V DC : 4.3g.cm (0.06 oz.in). Shafts A & B coupled when energised (terminals 1 and 2). Shafts A & C coupled when energised (terminals 3 and 4). Inertia (Energised) at 24-28 VDC : 8.0g.cm sq (0.045 oz.in sq) either coil, 10.7g.cm sq (0.060 oz.in sq) both coils. Clutches - Magnetic - Bu-Ord Size 18 Breakaway Torque (Energised) at 24-28 VDC : 14.4g.cm (0.20 oz.in). Breakaway Torque (De-Energised) at 24-28 VDC : 4.3g.cm (0.06 oz.in). Shafts a & B coupled when energised, braked when de-energised. Inertia (De-Energised) at 24-28 VDC : 2.74g.cm sq(0.038 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.18g.cm sq (0.072 oz.in sq). Clutches - Magnetic - Bu-Ord Size 18 - Reverse Acting Breakaway Torque (Energised) at 24-28 VDC : 3.6g.cm (0.05 oz.in). Breakaway Torque (De-Energised) at 24-28 VDC : 14.4g.cm (0.2 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 19g.cm sq (0.134 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.18g.cm sq (0.103 oz.in sq). Clutches - Magnetic - Bu-Ord Size 18 - Triplex Breakaway Torque (Energised) at 24-28 VDC : 14.4g.cm (0.20 oz.in). Breakaway Torque (De-Energised) at 24-28 VDC : 4.3g.cm (0.06 oz.in). Shafts A & B coupled when energised (terminals 1 and 2). Shafts A & C coupled when energised (terminals 3 and 4). Inertia (Energised) at 24-28 VDC : 19.2g.cm sq (0.108 oz.in sq) either coil, 25.86g.cm sq (0.145 oz.in sq) both coils. Clutches - Magnetic Particle 24VDC Ultrafast Responses. The input shaft becomes coupled to the output shaft with electrical excitation. Shafts have a flat on the end. Soft or fast start. Couplings - Oldham Couplings - Oldham - Precision Spring Loaded 2.8 to 4.2 Nm. Max Speed: 3000 RPM. Max Speed: 3000 RPM. Max Backlash: 5 minutes. Max parallel shaft offset: 0.381mm. Max angular offset: 1.5 Degrees. 303 Stainless Steel. Diamond Knurled Tip Set Screws Socket Set Screws - Diamond Knurled Tip Grips rough shafts. The ball can rotate up to 9 Deg. to fasten the object securely. Gearboxes - Basic Gearboxes - Light Duty - Base Mount Approx weight 115 grams. Discontinued group. Minimum quantities will apply to manufacture. Helical Gears. Brass Bearings. Backlash: 3 Deg Nominal - Max 8 Deg including endplay. Aluminium Alloy housing and base. Plated steel shafts. Gearboxes - Light Duty - Panel Mount Approx weight 115 grams. SRLP Series. Helical Gears. Brass Bearings. Backlash: 3 Deg Nominal - Max 8 Deg including endplay. Aluminium Alloy housing. Plated steel shafts. Gearboxes - Cross Axis Gearboxes - Cross Axis - 83.3 x 76.2 x 44.5 Worm Gear - 64DP Precision. Max input speed 1000 RPM. Right or left hand. Can only be driven from input shaft. Maximum Backlash 30 minutes. Permanently Lubricated. Gearboxes - Offset Gearboxes - Offset - 60 x 60 Base mounted. SRBM60 Series. Die cast aluminium Housing. Steel Shafts. Bearings Input / Output : Ball / Sintered Bronze. Steel and Phenolic Gears. Shaft Play Radial / Thrust : <= 0.1mm / <=0.3mm. Operating Temp : -10 to 60 Deg C | Approx weight : 26 grams. Gearboxes - Right Angle Gearboxes - Right Angle - 30.0 x 30.0 x 18.0mm Economy Bevel Gear Type. Miniature gearbox. Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel. Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox. 1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application. Gearboxes - Right Angle - 40.0 x 40.0 x 25.0mm BLH20 Series. Miniature gearbox. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Right Angle - 40.0 x 40.0 x 25.0mm (B) Economy Bevel Gear Type. GDRA Series. Miniature gearbox. Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel. Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm Economy Bevel Gear Type. GDRA Series. Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel. Gearboxes - Right Angle - 55.0 x 55.0 x 34.0mm BLH30 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Right Angle - 63.0 x 63.0 x 40.0mm Economy Bevel Gear Type. GDRABE Series. Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel. Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm BLH40 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Right Angle - 82.0 x 62.0 x 40.0mm GDRHD Series. Max Rated Speed 3600 RPM - Reversible / Unit weight 0.4kg. Aluminium Die Cast Housing. Alloy Steel Shafts. Spiral Bevel Gears, Case Hardened alloy steel. Torque ratings table (after listings) shows ratings for X axis = 2 and Y axis = 1. Temp Range minus 10 to Plus 40 Deg C. Gearboxes - Right Angle - 100.0 x 100.0 x 60.0mm BLH50 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Right Angle - 125.0 x 125.0 x 80.0mm BLH60 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Right Angle - 140.0 x 107.0 x 66.0mm GDRHD Series. Max Rated Speed 3600 RPM - Reversible / Unit Weight 1.8kg. Aluminium Die Cast Housing. Alloy Steel Shafts. Spiral Bevel Gears, Case Hardened alloy steel. Torque ratings table (after listings) shows ratings for X axis = 2 and Y axis = 1. Temp Range minus 10 to Plus 40 Deg C. Gearboxes - Right Angle - 140.0 x 140.0 x 98.0mm BLH70 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Right Angle - 166.0 x 128.0 x 76.0mm GDRHD Series. Max Rated Speed 3600 RPM - Reversible / Unit Weight 3.1kg. Aluminium Die Cast Housing. Alloy Steel Shafts. Spiral Bevel Gears, Case Hardened alloy steel. Torque ratings table (after listings) shows ratings for X axis = 2 and Y axis = 1. Temp Range minus 10 to Plus 40 Deg C. Gearboxes - Tee Gearboxes - Tee - 40.0 x 40.0 x 25.0mm BLHT20 Series. Miniature gearbox. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Tee - 55.0 x 40.0 x 25.0mm Bevel Gears - 0.53 to 1.77 Nm. BLHM20 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Tee - 55.0 x 55.0 x 34.0mm BLHT30 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Tee - 74.0 x 55.0 x 34.0mm Bevel Gears - 1.32 to 4.40 Nm. BLHM30 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Tee - 75.0 x 75.0 x 44.0mm BLHT40 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Tee - 82.0 x 74.0 x 40.0mm GDRHD Series. Max Rated Speed 3600 RPM - Reversible / Unit Weight 0.5kg. Aluminium Die Cast Housing. Alloy Steel Shafts. Spiral Bevel Gears, Case Hardened alloy steel. Torque ratings table (after listings) shows ratings for X axis = 2 and Y axis = 1. Temp Range minus 10 to Plus 40 Deg C. Gearboxes - Tee - 100.0 x 75.0 x 44.0mm Bevel Gears - 3.0 to 10.3 Nm. BLHM40 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Tee - 100.0 x 100.0 x 60.0mm BLHT50 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Tee - 125.0 x 125.0 x 80.0mm BLHT60 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Tee - 135.0 x 100.0 x 60.0mm Bevel Gears - 7.7 to 30.0 Nm. BLHM50 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Tee - 140.0 x 132.0 x 66.0mm GDRHD Series. Max Rated Speed 3600 RPM - Reversible / Unit Weight 2.2kg. Aluminium Die Cast Housing. Alloy Steel Shafts. Spiral Bevel Gears, Case Hardened alloy steel. Torque ratings table (after listings) shows ratings for X axis = 2 and Y axis = 1. Temp Range minus 10 to Plus 40 Deg C. Gearboxes - Tee - 140.0 x 140.0 x 98.0mm BLHT70 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Tee - 166.0 x 160.0 x 76.0mm GDRHD Series. Max Rated Speed 3600 RPM - Reversible / Unit Weight 3.4kg. Aluminium Die Cast Housing. Alloy Steel Shafts. Spiral Bevel Gears, Case Hardened alloy steel. Torque ratings table (after listings) shows ratings for X axis = 2 and Y axis = 1. Temp Range minus 10 to Plus 40 Deg C. Gearboxes - Tee - 170.0 x 125.0 x 80.0mm Bevel Gears - 19.0 to 70.0 Nm. BLHM60 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearboxes - Tee - 180.0 x 140.0 x 98.0mm Bevel Gears - 26.0 to 128.0 Nm. BLHM70 Series. Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620). Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2. Gearheads - Inline Gearheads - Inline - 12 mm x Various Lengths 12mm Diameter - Suits 1mm Motor shaft. Input and Output shafts have same centre line. Input and output in same direction. Requires 0.15 Module pinion as shown in tables. Suits 1mm Motor Shaft. Gearheads - Inline - 16 mm x Various Lengths 16mm Diameter - Suits 1.5mm Motor Shaft. Input and Output shafts have same centre line. Input and output in same direction. Requires 0.15 Module pinion as shown in tables. Suits 1.5mm Motor Shaft. Gearheads - Inline - 20 x 21mm 20mm Diameter - Suits 2mm Motor Shaft. Input and output in same direction. Requires 0.25 Module pinion as shown in tables. Suits 2mm Motor Shaft. Gearheads - Inline - 22 mm x Various Lengths 22mm Diameter - Suits 2mm Motor Shaft. Input and output in same direction. Requires 0.25 Module pinion as shown in tables. Suits 2mm Motor Shaft. Gearheads - Inline - 27 x 21.6mm 27mm Diameter - Suits 2mm Motor Shaft. Input and output in same direction. Requires 0.2 Module pinion as shown in tables. Suits 2mm Motor Shaft. Gearheads - Inline - 37 mm x Various Lengths 37mm Diameter - Suits 2mm Motor Shaft. Input and output in same direction. Requires 0.5 Module pinion as shown in tables. Suits 2mm Motor Shaft. Gearheads - Inline - 42 x 31.5mm 42mm Diameter - Suits 3mm Motor Shaft. Input and output in same direction. Requires 0.4 Module pinion as shown in tables. Suits 3mm Motor Shaft. Gearheads - Inline - 42.5 x 11.3mm 42mm Diameter - Suits 2mm Motor Shaft. Can be used as replacement gearheads for --- Gearmotors - DC - Size 42 Light Duty. Use with pinion gear GS0.30-10-0200B0200-BR-N (0.3 module). Suits 2mm Motor Shaft. Gearheads - Inline - 43 mm Square x Various Lengths 43mm Square - Suits 4mm Motor Shaft. Can be used as replacement gearheads for --- Gearmotors - DC - Size 43. Requires 0.6 Module pinion as shown in tables. Suits 4mm Motor Shaft. Gearheads - Inline - 48 mm Square x 28.2mm 48mm Square - Suits 3mm Motor Shaft. Can be used as replacement gearheads for --- Gearmotors - DC - Size 48. Requires 0.4 Module pinion as shown in tables. Suits 3mm Motor Shaft. Gearheads - Inline - 60 mm Square x 36.2mm 60mm Square - Suits 4mm Motor Shaft. Can be used as replacement gearheads for --- Gearmotors - DC - Size 60 (D33S52M and D33S57M54 series). Requires 0.5 Module pinion as shown in tables. Suits 4mm Motor Shaft. Gearheads - Inline - 60 mm Square x Various Lengths 60mm Square - Suits 4mm Motor Shaft. Can be used as replacement gearheads for --- Gearmotors - A.C. Single Phase - Size 60. Can be used as replacement gearheads for --- Gearmotors - DC - Size 60 (D33S54M Series). Requires 0.5 Module pinion as shown in tables. Suits 4mm Motor Shaft. Gearheads - Inline - Planetary - Size 17 - Precision Use with NEMA Size 17 Motors. Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 25.4kg (57 lbs) radial and 24.5kg (55 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Inline - Planetary - Size 17 - Standard Use with NEMA Size 17 Motors. Anodised aluminium housing - Heat Treated Steel Gears - Sealed ball bearings. Shaft loading 8.9kg (20 lbs) radial and 61kg (138 lbs) axial at 250rpm Output / Maximum input speed 4000 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 13 arc min, Double Stage : 15 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Inline - Planetary - Size 23 - Adapted With Nema and Non Nema Size Adaptors. Anodised aluminium housing - Heat Treated Steel Gears - Sealed ball bearings. Shaft loading 26kg (60 lbs) radial and 64kg (145 lbs) axial at 250rpm Output / Maximum input speed 4000 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 13 arc min, Double Stage : 15 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Inline - Planetary - Size 23 - Economy Use with NEMA Size 23 Motors. Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium Flanges. Shaft loading 66kg (150 lbs) radial and 66kg (150 lbs) axial / Maximum input speed 4000 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 10 arc min, Double Stage : 14 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Inline - Planetary - Size 23 - Precision Use with NEMA Size 23 Motors. Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 154kg (347 lbs) radial and 153kg (344 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Inline - Planetary - Size 34 - Adapted With Nema and Non Nema Size Adaptors. Anodised aluminium housing - Heat Treated Steel Gears - Sealed ball bearings. Shaft loading 44kg (100 lbs) radial and 88kg (200 lbs) axial at 250 rpm output / Maximum input speed 4000 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 13 arc min, Double Stage : 15 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Inline - Planetary - Size 34 - Economy Use with NEMA Size 34 Motors. Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 132kg (300 lbs) radial and 132kg (300 lbs) axial / Maximum input speed 4000 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 10 arc min, Double Stage : 14 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Inline - Planetary - Size 34 - Precision Use with NEMA Size 34 Motors. Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 388kg (875 lbs) radial and 376kg (849 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Inline - Planetary - Size 42 - Adapted With Nema and Non Nema Size Adaptors. Anodised aluminium housing - Heat Treated Steel Gears - Sealed ball bearings. Shaft loading 53kg (120 lbs) radial and 120kg (270 lbs) axial / Maximum input speed 4000 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 13 arc min, Double Stage : 15 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Inline - Planetary - Size 56 - Economy Use with NEMA Size 56 Motors. Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 446kg (1000 lbs) radial and 446kg (1000 lbs) axial / Maximum input speed 4000 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 10 arc min, Double Stage : 14 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Inline - Planetary - Size 56 - Precision Use with NEMA Size 56 Motors. Stainless Steel housing - Heat Treated Steel Gears - Sealed ball bearings - Aluminium mounting flange. Shaft loading 937kg (2100 lbs) radial and 937kg (2100 lbs) axial / Maximum input speed 6500 rpm. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 6 arc min, Double Stage : 10 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Inline - Planetary - Size 60 - Adapted With Nema and Non Nema Size Adaptors. Maximum input speed 4000 rpm. Shaft loading 41kg (92 lbs) radial and 197kg (442 lbs) axial at 250rpm output. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 8 arc min, Double Stage : 9 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Inline - Planetary - Size 90 - Adapted With Nema and Non Nema Size Adaptors. Maximum input speed 4000 rpm. Shaft loading 53kg (120 lbs) radial and 289kg (648 lbs) axial at 250rpm output. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 8 arc min, Double Stage : 9 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Inline - Planetary - Size 115 - Adapted With Nema and Non Nema Size Adaptors. Maximum input speed 4000 rpm. Shaft loading 82kg (184 lbs) radial and 526kg (1180 lbs) axial at 250rpm output. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 8 arc min, Double Stage : 9 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Right Angle Gearheads - Right Angle - Planetary - Size 17 Use with NEMA Size 17 Motors. Maximum input speed 5000 rpm. Shaft loading 25.4 kg (57 lbs) radial and 24.5 kg (55 lbs) axial. Min. Efficiency ---- Single Stage : 85%, Double Stage : 80%. Max Backlash ---- Single Stage : 10 arc min, Double Stage : 14 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Right Angle - Planetary - Size 23 - Adapted With Nema and Non Nema Size Adaptors. Maximum input speed 5000 rpm. Shaft loading 26.8 kg (60 lbs) radial and 66.9 kg at 250rpm output (150 lbs) axial. Min. Efficiency ---- Single Stage : 95%, Double Stage : 90%, Triple Stage : 85%. Max Backlash ---- Single Stage : 13 arc min, Double Stage : 15 arc min, Triple Stage : 15 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Right Angle - Planetary - Size 23 - Economy Use with NEMA Size 23 Motors. Maximum input speed 4000 rpm. Shaft loading 154.9 kg (347 lbs) radial and 153.5 kg (344 lbs) axial. Min. Efficiency ---- Single Stage : 85%, Double Stage : 80%. Max Backlash ---- Single Stage : 14 arc min, Double Stage : 18 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Right Angle - Planetary - Size 23 - Precision Use with NEMA Size 23 Motors. Maximum input speed 5000 rpm. Shaft loading 154.9 kg (347 lbs) radial and 153.5 kg (344 lbs) axial. Min. Efficiency ---- Single Stage : 85%, Double Stage : 80%. Max Backlash ---- Single Stage : 14 arc min, Double Stage : 18 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Right Angle - Planetary - Size 34 - Adapted With Nema and Non Nema Size Adaptors. Maximum input speed 5000 rpm. Shaft loading 45 kg (100 lbs) radial and 90 kg (200 lbs) axial. Min. Efficiency ---- Single Stage : 95%, Double Stage : 90%, Triple Stage : 85%. Max Backlash ---- Single Stage : 13 arc min, Double Stage : 15 arc min, Triple Stage : 15 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Right Angle - Planetary - Size 42 - Adapted With Nema and Non Nema Size Adaptors. Maximum input speed 5000 rpm. Shaft loading 54 kg (120 lbs) radial and 121 kg (270 lbs) axial. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 13 arc min, Double Stage : 15 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Right Angle - Planetary - Size 56 - Economy Use with NEMA Size 56 Motors. Maximum input speed 4000 rpm. Shaft loading 276 kg (620 lbs) radial and 276 kg (620 lbs) axial. Min. Efficiency ---- Single Stage : 85%, Double Stage : 80%. Max Backlash ---- Single Stage : 14 arc min, Double Stage : 18 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Right Angle - Planetary - Size 56 - Precision Use with NEMA Size 56 Motors. Maximum input speed 5000 rpm. Shaft loading 937 kg (2100 lbs) radial and 937 kg (2100 lbs) axial. Min. Efficiency ---- Single Stage : 85%, Double Stage : 80%. Max Backlash ---- Single Stage : 10 arc min, Double Stage : 14 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Right Angle - Planetary - Size 60 - Adapted With Nema and Non Nema Size Adaptors. Maximum input speed 5000 rpm. Shaft loading 37.5 kg (84 lbs) radial and 179 kg (400 lbs) axial. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 9 arc min, Double Stage : 9 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Right Angle - Planetary - Size 90 - Adapted With Nema and Non Nema Size Adaptors. Maximum input speed 5000 rpm. Shaft loading 48 kg (107 lbs) radial and 470 kg (1050 lbs) axial at 250 rpm output. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 9 arc min, Double Stage : 9 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Right Angle - Planetary - Size 115 - Adapted With Nema and Non Nema Size Adaptors. Maximum input speed 5000 rpm. Shaft loading 75 kg (168 lbs) radial and 479 kg (1073 lbs) axial. Min. Efficiency ---- Single Stage : 90%, Double Stage : 85%. Max Backlash ---- Single Stage : 9 arc min, Double Stage : 9 arc min. Operating Temperature : -34 to 121 Deg C (-29 to 250 Deg F). Gearheads - Right Angle - Spur Gear - Size 23 Use with NEMA Size 23 Motors. Maximum input speed 5000 rpm. Shaft loading 154.9 kg (347 lbs) radial and 153.5 kg (344 lbs) axial. Min. Efficiency ---- Single Stage : 85%. Max Backlash : 25 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Right Angle - Spur Gear - Size 42 Use with NEMA Size 42 Motors. Maximum input speed 5000 rpm. Shaft loading 167 kg (375 lbs) radial and 167 kg (375 lbs) axial. Min. Efficiency ---- Single Stage : 85%. Max Backlash : 25 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearheads - Right Angle - Spur Gear - Size 56 Use with NEMA Size 56 Motors. Maximum input speed 5000 rpm. Shaft loading 276 kg (620 lbs) radial and 276 kg (620 lbs) axial. Min. Efficiency ---- Single Stage : 85%. Max Backlash : 25 arc min. Operating Temperature : -54 to 121 Deg C (-65 to 250 Deg F). Gearmotors - AC Gearmotors - A.C. Single Phase - Size 60 Max Capacitance - Induction Type - 50 Hz 1.0uf / 60 Hz 0.8 uF. Max Capacitance - Hysteresis Type - 0.8uf. Unit Weight Approx 0.8 KG. Machined Aluminium Housing - Steel Shaft. Steel / Phenolic Gears - Bronze Bearings. Gearmotors - DC Gearmotors - Basic - Hobby - 12.1mm Diameter Small light weight geared motors used in toys and small solar applications NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications. Gearmotors - DC - Low Voltage Reversible - Low Voltage - Self Starting. Reversible. Low Voltage. Self Starting. Hosuing : Plastic / Shaft : Steel. Gearmotors - Stepper Gearmotors - Stepper - Nema Size 17 Max Input Speed: 1000 rpm. Shaft Loading: Radial and axial = 1.78 kg. Shaft Play (Max): Radial = 0.05mm (0.002 in.), End = 0.254mm (0.010 in.). Phase Resistance: 3.3 ohms +/- 10% at 25 Deg C. 1.8 Deg Nominal Motor Step Angle. Gearmotors - Stepper - Nema Size 23 Max Input Speed: 1000 rpm. Shaft Loading: Radial and axial = 6.7 kg. Shaft Play (Max): Radial = 0.05mm (0.002 in.), End = 0.254mm (0.010 in.). Phase Resistance: 0.37 ohms +/- 10% at 25 Deg C. 1.8 Deg Nominal Motor Step Angle. Gears - Spur - Circular Pitch Gears - Spur - Circular Pitch 2 PCD = No. of Teeth x 0.636mm (2.000 / Pi.). Various styles and materials. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Circular Pitch 5 PCD = No. of Teeth x 1.591mm (5.000 / Pi.). Various styles and materials. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Metric Sizes Gears - Spur - Module 0.15 PCD = No. of Teeth x 0.150mm. 20 Degree Pressure Angle. Brass. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.20 PCD = No. of Teeth x 0.200mm. 20 Degree Pressure Angle. Brass. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.25 PCD = No. of Teeth x 0.250mm. 20 Degree Pressure Angle. Brass and carbon steel. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.30 PCD = No. of Teeth x 0.300mm. 20 Degree Pressure Angle. Brass. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.40 PCD = No. of Teeth x 0.400mm. 20 Degree Pressure Angle. 416 stainless steel, acetal, brass and carbon steel. Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.50 PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel. Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.60 PCD = No. of Teeth x 0.600mm. 20 Degree Pressure Angle. Carbon steel. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.70 PCD = No. of Teeth x 0.700mm. 20 Degree Pressure Angle. Acetal. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.75 PCD = No. of Teeth x 0.750mm. 20 Degree Pressure Angle. Brass. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.80 PCD = No. of Teeth x 0.800mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel. Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 1.00 PCD = No. of Teeth x 1.000mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel. Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 1.25 PCD = No. of Teeth x 1.250mm. 20 Degree Pressure Angle. 303 stainless steel and acetal. Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 1.50 PCD = No. of Teeth x 1.500mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 2.00 PCD = No. of Teeth x 2.000mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 2.50 PCD = No. of Teeth x 2.500mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon. Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 3.00 PCD = No. of Teeth x 3.000mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon. Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - US Sizes - 14.5 Degree Gears - Spur - 16 Pitch - 14.5 Degree PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5 Degree Pressure Angle. Nylon. Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 24 Pitch - 14.5 Degree PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5 Degree Pressure Angle. Nylon, brass and carbon steel. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 32 Pitch - 14.5 Degree PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 48 Pitch - 14.5 Degree PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - US Sizes - 20 Degree Gears - Spur - 16 Pitch - 20.0 Degree PCD = No. of Teeth x 1.588mm (1/16 in.). 20 Degree Pressure Angle. Nylon and acetal. Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 24 Pitch - 20.0 Degree PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 32 Pitch - 20.0 Degree PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 48 Pitch - 20.0 Degree PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 64 Pitch PCD = No. of Teeth x 0.397mm (1/64 in.). 20 Degree Pressure Angle. 5052 aluminium, stainless steel, acetal and brass. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 72 Pitch PCD = No. of Teeth x 0.353mm (1/72 in.). 20 Degree Pressure Angle. 2024 aluminium, stainless steel and acetal. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 80 Pitch PCD = No. of Teeth x 0.318mm (1/80 in.). 20 Degree Pressure Angle. 2024 aluminium and 303 stainless steel. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 96 Pitch PCD = No. of Teeth x 0.265mm (1/96 in.). 20 Degree Pressure Angle. 2024 aluminium and 303 stainless steel. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 120 Pitch PCD = No. of Teeth x 0.212mm (1/120 in.). 20 Degree Pressure Angle. 2024 aluminium and 303 stainless steel. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Grips - Taper Grips - Taper Duroplastic FS31 black. Axle and threaded bush in Steel. Surface Finish: All edges smoothed and highly polished. To assemble unscrew shaft. The grips fit the disk handwheels with revolving taper grip. Handles - Clean Line Handles - Clean Line - Style 2 High impact strength special technopolymer, in white similar to RAL 9002 with bright finish. Resistant to solvents, oils, greases and other chemical agents. Push fitting on plain shaft made from standard h9 tolerance bright drawn stock bars. Elastic coupling: the handle is not affected by vibrations and does not tend to loosen. Hobby Bearings Hobby Bearings - Roller Clutch Roller Clutch Bearings rotate in one direction only. Drawn Cup Type. The roller clutches in this listing are all DRAWN CUP TYPE. Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm. Refer to main listing for Roller Clutches for sizes not listed here. Hobby Motors Hobby Motor Selection - Electric DC A small selection of popular sizes. See main listings for sizes not shown here. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Housings - Linear with Bearings Housings - Linear - Pillow Block Includes Bearings. Housing: Aluminium - carbon steel and engineered polymer bearing fitted. Super Smart Ball Bushing™ Bearing fitted. Designed for use with Hard Linear Shafting (h6 Tolerance). Housings - Linear - Twin Pillow Block Includes Bearings. Housing: Aluminium - carbon steel and engineered polymer bearing fitted. Super Smart Ball Bushing™ Bearing fitted. Designed for use with Hard Linear Shafting (h6 Tolerance). Housings with Integral Bearing Housings - Bearing - Blocks - Bronze Bearing Aluminium with 5 percent self aligning sintered bronze bearing. Bearing: Bronze SAE 840 (oil impregnated). / Housing: Sintered Aluminium / Corrosion Resistant. Mating shaft recommendation: Min. hardening 100 HRB (Rockwell B). Max surface finish 16 RMS. Recommended shaft clearance is 0.013 - 0.038mm, using lower limit of bore tolerance. Maximum Load and Speed: The figure shown in the plain bearing data are maximums, for guidance only, and cannot be combined. The performance of a plain bearing is stated as a PV value, which is the product of a pressure and velocity. Housings - Bearing - Flanged - Bronze Bearing ±5° Static Alignment. Bearing: Bronze SAE 840 (oil impregnated). Housing: Sintered Aluminium. Bearing Retainer: Outer retainer is steel (which is clinched into Aluminium housing) with a Nylon washer on first face. Apply appropriate factor of safety to the nominal loads and speeds specified. Mating shaft rec. Min. 100 HRB. Max surface finish 16 RMS. Rec. shaft clearance 0.013 - 0.038mm. Hubs Hubs - Gear and Dial - Single Fairloc Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Internal Lock Washers Washers - Lock - Internal These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require. Knobs - Pointer Knobs - Pointer - 18T Spline Type Push on suits 18 tooth splined 6.35mm (1/4 inch) shaft. Knobs - Pointer - Aluminium and Plastic Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass Insert. White Pointer. Knobs - Pointer - Arrow Top Push on. Suits 6.35mm (1/4 inch) shaft. Knobs - Pointer - Black Aluminium Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Knobs - Pointer - Brushed Aluminium Push on. Suits 6.35mm (1/4 inch) shaft. Knobs - Pointer - Coloured Cap Push on. Suits 6.35mm (1/4 inch) shaft. Knobs - Pointer - Skirted Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass insert. Knobs - Pointer - Skirted - Numbered Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass insert. Leadscrews and Nuts Leadscrew Nuts - Trapezoidal - Round - Plastic - Nylon 6.6 Use with trapezoidal leadscrews listed in separate category. Material: Black Nylon 6.6. Wear Measured by Weight Reduction: 1.94wt.-%. Test Conditions: Load Direction: Horizontal Shaft Material: Stainless Steel Load: 10kg. Test Conditions: Speed: 300Rpm Cycles: 10,000 Stroke: 160mm Lubrication: None. Maintenance free. Support higher loads. Dry running. Dirt resistance. Limit Stops Limit Stops - Electromagnetic Adjustable Limits. Material: Cast aluminium, black anodised. Shaft: Stainless Steel. Ball bearings used throughout. Four miniature single pole double throw switches. Two adjusting screws to permit simple accurate adjustment of the miniature switch actuators. Linear Ball Splines Linear Ball Splines - Bearings - Flanged Use with Linear Ball Spline Shaft. Linear Ball Splines - Bearings - Unflanged Use with Linear Ball Spline Shaft. Motors - Hobby - Robotic - Appliances Motors - DC 13.05X24.4 mm M-300C Series 0.5 to 6 VDC - 1820 to 2700 RPM. See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx. 22 grams. Motors - DC 16.6X32 mm M-500T Series 1.5 to 9 VDC - 1430 to 2230 RPM. See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Motors - DC 18.9X18X9.5 mm M-020 Series - 1 to 3 VDC - 3700 to 11000 RPM. See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx 9.5 grams. Motors - DC 25x20.1X15.1 mm M-13 Series - 1.5 to 24 VDC - 4500 to 13760 RPM. See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Motors - DC 25X21 mm M-14 Series 1.5 to 3 VDC - 4230 to 11280 RPM. See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Motors - DC 26.9X23.8 mm M-26 Series 1.5 to 24 VDC - 2500 to 15100 RPM. See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Motors - DC 26.9X24.2X18.3 mm MF-26 Series - 1.5 to 24 VDC - 3600 to 15900 RPM. See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Motors - DC 30.5X24.2 mm M-28 Series 1.5 to 24 VDC - 2830 to 14250 RPM. See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Motors - DC 30.5X24.2X18.3 mm MF-28 Series - 1.5 to 24 VDC - 4470 to 13430 RPM. See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Motors - Ondrives - DC Motors - DC - Size 63 Ondrives Performance data is based upon an operating temperature of 25°C. Commutation: Graphite, No. of Sectors: 12. Brushes: Rotary, Magnets: Ferrite, Axial Backlash: <0.15mm, Radial Backlash: <0.15mm. Maximum Axial Load: 150N, Maximum Radial Load at 20mm: 150N. Maximum Shaft Push Pressure: 200N, Operating Temperature Range: -20°C to +85°C, Mass: 1.2 to 1.7kg. Motors - DC - Size 80 Ondrives Performance data is based upon an operating temperature of 25°C. Commutation: Graphite, No. of Sectors: 12. Brushes: Rotary, Magnets: Ferrite, Axial Backlash: <0.15mm, Radial Backlash: <0.15mm. Maximum Axial Load: 180N, Maximum Radial Load at 30mm: 200N, Maximum Shaft Push Pressure: 200N. Maximum Operating Speed: 5,000 Rpm, Operating Temperature Range: -20°C to +85°C, Mass: 2.8 to 4kg. Maximum Housing Temperature: +80/84°C, Starting Voltage: 0.7V to 1.0V. Motors - Stepper - Drives Motors - Stepper - Drive Modules 1.8 Deg Step Angle. Complete with 6.35mm Shaft Coupling. Motors - Stepper - Drives with Gearheads Not recommended for precision applications. Approx 2 Deg backlash at output shaft. Motors - Stepper - With Gearheads to Match Motors - Stepper - With Gearheads to Match Select motor and gearhead separately. Type 3110 Gearheads suit Type 3110 Motor. Type 3120 Gearheads suit Type 3120 Motor. 1.8 Deg Step Angle. Approx 2 Deg Backlash at output shaft. Insulation Class B. Position Indicators Position Indicators - Digital - Clamping Plates Housing: Aluminium, anodised. Clamping Lever: Plastic, snap in. A combination of the digital indicator with this practical accessory forms a reliable shaft clamp. Without additional design work it is possible to prevent automatic shaft movements in a fast and secure way. For shaft diameters 8 to 20 mm. Pulleys - Flat Belt - Idler Pulleys - Flat Belt - Idler Complete with Needle Roller Bearing. Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners. Pulleys - Timing - Idler Pulleys - Timing - Idler Complete with Needle Roller Bearing. Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners. Pulleys - Vee - Idler Pulleys - Vee - Idler Complete with Needle Roller Bearing. Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners. Push On Retainers Push On Retaining Rings - Basic M1465 / DTX / Seeger ZA and KS. Thrust load shown is calculated for ideal conditions with mild steel shaft. If no thrust load is shown, testing is suggested. Spacers - Round Spacers - Round - Through Bore - Brass Shaft spacers - Brass Spacers - Round - Through Bore - Nylon Shaft spacers - Nylon Spacers - Round - Through Bore - Stainless Steel Shaft spacers - Stainless Steel Spacers - Round - Through Bore - Steel Shaft spacers - Steel Sprockets - Roller Chain Sprockets - Roller Chain - Idler Complete with Needle Roller Bearing. Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners. Tighteners - Drive Tighteners - Drive Malleable Iron construction. Shaft and Collar : Hardened Steel. Use with Idler pulleys and sprockets. Washers - Self Aligning Washers - Self Aligning AISI 303 Stainless Steel or Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces. Too many choices? You have selected to see ALL categories containing the term SHAFT. Click here to see ONLY THE MOST POPULAR categories containing the term SHAFT.

Cart total A$ 0.00 Currency Options Default (Australian Dollar) British Pound Canadian Dollar Euro Hong Kong Dollar Japanese Yen New Zealand Dollar Singapore Dollar US Dollar You may need to refresh the page if your selected currency doesn't change. Item Popularity Show only popular categories Pictures Remove pictures Show all categories starting with A B C D E F G H I J K L M N O P Q R S T U V W X Y Z Major Categories Balls Bearings Belts Ceramic Chain Circlips and Clips Collars Couplings Dental Bearings and Parts Dual Vee Gearboxes Gears Grub Screws Handpiece Parts Keysteel Knobs Spacers Motors Mounts Nuts Parts Boxes Pins Pulleys Racks Rod Screws Seals Shafting Shim Springs Sprockets Tools Tube Universal Joints Washers SEARCH Guided Search Product Type (Category) Information Search Part Number (ours) Part Number (other) CATALOGUES Catalogues Index Catalogue A-Z Online Catalogues A-Z PDF Discount Registration Online Catalogue Quick Guides HOW TO & ABOUT US Charity Contact Us Frequently Asked Questions Freight Rates Home How To Order Online Mailorder Newsletter Subscription Order Specially Quoted Parts Payment Options Terms and Conditions of Sale PRODUCT INFO Dental Bearings Hobby Information Information Sheets New Products Specials Lists Technical Information RECOMMENDED LINKS Couplings Information eParcel Tracking Express International Tracking Gearboxes Information Hobby Engineering Supplies Jokes and Trivia Materials Information Miniature Bearings Australia Ondrives UK Rino UK Shafting Information Stainless Selection Tingalpa Model Aero Club TNT Freight Tracking Unfair Contracts Wikipedia Windows to The Universe World Time

• Search for information pages instead of products
• Mail Order Form
• Order non-standard parts quoted by e-mail
• Freight Rates
• Terms of Sale

All care has been taken in the compilation of this page, however errors may occur. Please do not use the information contained herein for critical applications without first re-checking the information with an independent source. No responsibility will be accepted by Small Parts and Bearings or the Directors of said company for any loss of any kind that may be incurred in any way whatsoever from use of the information provided in these pages.

***** Trademarks *****

Delrin^TM is a registered trademark of duPont Corporation
Teflon^TM is a registered trademark of duPont Corporation

SPB Terms and Conditions of Sale

SPB Privacy Policy

SPB Freight Rates