Pulleys Vee B 5l Single Row For Qd Bushing Categories


Category Matches

Pulleys Vee

TopHide Pictures

Pulleys - Vee - B - 5L - Single Row - For QD Bushing
Pulleys - Vee - B - 5L - Single Row - For QD Bushing

Search Rating: 52%

Also see combined categories:
All Vee Pulleys B Section 15.9 and 16.5mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.

Related Information:

Pulleys - Vee - A - 4L - Single Row - For QD Bushing
Pulleys - Vee - A - 4L - Single Row - For QD Bushing

Search Rating: 51%

Also see combined categories:
All Vee Pulleys A Section 12.5 and 12.7mm Top Width

Cast iron pulleys. QD bushings are used to vary the bore sizes.

Related Information:

Bushings - QD and Taperlock

TopHide Pictures

Bushings - QD
Bushings - QD

Search Rating: 35%

Used with QD type cast iron vee pulleys, timing pulleys, sprockets, poly vee pulleys and other parts designed specifically for use with a QD bushing

Similar to a taperlock bush, but not interchangeable. QD bushings like taperlock bushings allow for use of a single stock pulley for many applications with different shaft sizes. Select the correct QD series to suit the pulley.


Pulleys Vee

TopHide Pictures


Pulleys - Vee - A - 4L - Single Row - Through Bore - Cast Iron
Pulleys - Vee - A - 4L - Single Row - Through Bore - Cast Iron

Search Rating: 30%

Also see combined categories:
All Vee Pulleys A Section 12.5 and 12.7mm Top Width

Dual purpose pulleys suit A section and M section belts

To determine the pitch diameter for M section deduct 8.636mm (0.34 inch) from the pitch diameter listed.

Related Information:

Pulleys - Vee - M - 3L - Single Row - Through Bore - Aluminium
Pulleys - Vee - M - 3L - Single Row - Through Bore - Aluminium

Search Rating: 30%

Also see combined categories:
All Vee Pulleys M Section 10mm Top Width

Stenco vee pulleys

Related Information:

Pulleys - Vee - M - 3L - Single Row - Through Bore - Cast Iron
Pulleys - Vee - M - 3L - Single Row - Through Bore - Cast Iron

Search Rating: 30%

Also see combined categories:
All Vee Pulleys M Section 10mm Top Width

Dual purpose pulleys suit A section and M section belts

To determine the pitch diameter for A section add 8.636mm (0.34 inch) to the pitch diameter listed.

Related Information:


Bushes Plastic

TopHide Pictures

Bushings - Snap - Closed
Bushings - Snap - Closed

Search Rating: 27%

Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Open snap bushings are designed to provide protection from sharp edges where cable or hose runs through plate steel.

Similar to a bung, but designed with expanding catch for use in holes in sheet products. Also see grommets for a similar product made from rubber.

Related Information:

Bushings - Snap - Open
Bushings - Snap - Open

Search Rating: 27%

Quality UL approved 6/6 nylon with flammabilty rating of 94V-2. Closed snap bushings are designed to keep out dust and other contaminants and protect from sharp edges where cable or hose used to run through a hole in plate steel.

Also called a dome plug. Also see grommets for a similar product made from rubber.

Related Information:

Bushes - Plastic - Iglidur G - Flanged
Bushes - Plastic - Iglidur G - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

Bushes - Plastic - Iglidur G - Unflanged
Bushes - Plastic - Iglidur G - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

General purpose maintenance free dry running.

Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

Bushes - Plastic - Iglidur H - Flanged
Bushes - Plastic - Iglidur H - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur H - Unflanged
Bushes - Plastic - Iglidur H - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater performance. High Temp. Chemical Resistance.

Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 175 Mpa. Hardness 87 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur M250 - Flanged
Bushes - Plastic - Iglidur M250 - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

Bushes - Plastic - Iglidur M250 - Unflanged
Bushes - Plastic - Iglidur M250 - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

For impact resistance vibration dampening unclean environments.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.

Related Information:

Bushes - Plastic - Iglidur P - Flanged
Bushes - Plastic - Iglidur P - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur P - Unflanged
Bushes - Plastic - Iglidur P - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low water absorption. Low wear. Hgh load.

Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 75 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur J - Flanged
Bushes - Plastic - Iglidur J - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur J - Unflanged
Bushes - Plastic - Iglidur J - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.

Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur Q - Flanged
Bushes - Plastic - Iglidur Q - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur Q - Unflanged
Bushes - Plastic - Iglidur Q - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Excellent wear resistance under high load. Resistant to dirt.

Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur F - Flanged
Bushes - Plastic - Iglidur F - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur F - Unflanged
Bushes - Plastic - Iglidur F - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.

Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur W300 - Flanged
Bushes - Plastic - Iglidur W300 - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur W300 - Unflanged
Bushes - Plastic - Iglidur W300 - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Low co-efficient of friction. High wear resistance. Chemical resistant.

Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur Z - Flanged
Bushes - Plastic - Iglidur Z - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur Z - Unflanged
Bushes - Plastic - Iglidur Z - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

High temperature. High thermal resistance. Extreme load. High surface speed.

Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 oC = 95 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Pins Dowel

TopHide Pictures

Pins - Dowel Bushings
Pins - Dowel Bushings

Search Rating: 26%

Also see combined categories:
All Dowel Bushings

Series DB100 Spirol

Spring Steel. Precision rolled bushes manufactured from spring steel. Designed to eliminate the need for separate dowling where two components are to be located accurately together and fastened with bolts. They are available for use with bolts from M5 to M12.


Bushes Plastic

TopHide Pictures

Bushes - Plastic - Iglidur H370 - Flanged
Bushes - Plastic - Iglidur H370 - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur H370 - Unflanged
Bushes - Plastic - Iglidur H370 - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.

Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur A200 - Flanged
Bushes - Plastic - Iglidur A200 - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur A200 - Unflanged
Bushes - Plastic - Iglidur A200 - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur A290 - Flanged
Bushes - Plastic - Iglidur A290 - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur A290 - Unflanged
Bushes - Plastic - Iglidur A290 - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Food grade for low speeds and direct contact with food and pharmaceuticals.

Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur X - Flanged
Bushes - Plastic - Iglidur X - Flanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Flanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Bushes - Plastic - Iglidur X - Unflanged
Bushes - Plastic - Iglidur X - Unflanged

Search Rating: 26%

Also see combined categories:
All Plastic Bushes
All Unflanged Plastic Bushes

Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.

Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.


Pulleys Poly Vee

TopHide Pictures

Pulleys - Poly V - J Section - QD Bush
Pulleys - Poly V - J Section - QD Bush

Search Rating: 25%

Use with QD bush to suit your bore requirement

Poly V drives are ideal for high ratio drives and high speed. J Section is 2.34mm pitch and 3.56mm belt height.


Spacers

TopHide Pictures

Spacers - Machinery Bushings
Spacers - Machinery Bushings

Search Rating: 24%

Also see combined categories:
All Round Spacers
All Flat Washers and Spacers - Metallic

Used as spacers between pulleys, gears etc

Low carbon mild steel.


Locking Compounds

TopHide Pictures

Retaining Compounds
Retaining Compounds

Search Rating: 23%

Also see combined categories:
All Adhesives

Molytec and Loctite. Includes Quickmetal. High and medium retaining for bearings, bushes, gears, pulleys and sprockets.

Related Information:


Show all items starting with
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   1   2   3   4   5   6   7   8   9  





Other Store Pages

Click Page Banner Below

Top

Main Pages

Click Page Banner Below

Top





Top



Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 124406 products in 3083 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts and Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.