Categories that include the term: NYLON
|
RELEVANCE
****VERY HIGH**** 100% All search words found in headers or categories |
Acme Thread |  |
Leadscrew Nuts - Trapezoidal - Round - Plastic - Nylon 6.6
Use with trapezoidal leadscrews listed in separate category.
|
Acorn Nuts | |
Nuts - Dome - Nylon
Natural Nylon.
|
Aluminium Nuts | |
Nuts - Hexagonal - Nylon Insert - Aluminium
Nylon Insert for Locking.
|
Balls | |
Balls - Nylon
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
|
Bar | |
Rod - Round - Nylon
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
|
Bearing Housings | |
Housings - Bearing - Blocks - Nylon
Moulded Nylon 101 Housing. Suit miniature bearings.
|
Housings - Bearing - Blocks - Nylon with Ertalyte Bearing
Flanged Ertalyte Bearing in Moulded Nylon 101 Housing.
|
Housings - Bearing - Blocks - Nylon with Stainless Bearing
Moulded Nylon 101 Housing with 440C Stainless Bearing.
|
Bearings - Bushes | |
Bushes - Plastic - Natural Nylon
|
Blow Guns - Trigger Action | |
Blow Guns - Trigger Action - Nylon
Adjustable gap.
|
Cap Head Socket Screws | |
Screws - Socket - Cap - Nylon
UNC - UNF - METRIC - Non Conductive - Non Magnetic.
|
Castors | |
Castors - Nylon
Nylon general purpose castors including fixed, swivel and brake types. Long life, economical, easy to roll on smooth hard surfaces, easy to roll under load
|
Countersunk Flat Head Screws | |
Screws - Machine - Nylon - Countersunk Head
Flat Head Countersunk UNC and UNF.
|
Fasteners - Grub Screws - Specialty | |
Socket Set Screws - Nylon Tipped
Soft tip compresses into threads to become self locking.
|
Fasteners - Nuts - Hexagonal | |
Nuts - Hexagonal - Nylon
|
Nuts - Hexagonal - Nylon - Self Tapping
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel
Nylon Insert for Locking.
|
Nuts - Hexagonal - Nylon Insert - Steel
Nylon Insert for Locking.
|
Nuts - Hexagonal - Nylon Insert - Titanium
Nylon Insert for Locking. 6AL-4V (Grade 5) High strength titanium alloy.
|
Fasteners - Nuts - Wing | |
Nuts - Wing - Nylon
|
Fasteners - Screws - Machine | |
Screws - Machine - Nylon
UNC / UNF / Metric. Pan head, cheese head, binder head.
|
Fasteners - Washers | |
Washers - Flat - Nylon
Flat washers.
|
Washers - Shoulder - Nylon
|
Hex Spacers | |
Spacers - Hex - Threaded - Nylon
Threaded Hex Spacers.
|
Hobby Nuts | |
Hobby Nuts - Nylon Locking
A small selection of popular sizes.
See main listings for sizes not shown here. Nylon Insert for Locking.
|
Materials | |
Sheet - Nylon
|
Nylon Grub Screws | |
Socket Set Screws - Cup Point - Standard
Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Nylon Screws | |
Screws - Hex Head - Plastic
UNC - UNF - METRIC - Nylon and PVC.
|
Threaded Rod - Plastic
UNC - UNF - METRIC - Nylon and PVC.
|
Spacers - Round | |
Spacers - Round - Through Bore - Nylon
Shaft spacers - Nylon
|
RELEVANCE
**LOW** All search words found in category description |
Assorted Knobs | |
Screws - Thumb
Steel, stainless and nylon.
|
Ball Bearings | |
Bearings - High Speed Cage
Bearings with cages for high speed applications, including phenolic, nylon and polyamide.
|
Bearings - Acetal | |
Bearings - Acetal - with 302 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 302 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Acetal - with 316 Stainless Steel Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Acetal - with Glass Balls
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Ceramic | |
Bearings - Ceramic Si3N4
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls, cage and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Ceramic ZrO2
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Belts - Timing - 2.032 mm MXL | |
Belts - Timing - 2.032mm Pitch - MXL TruMotion
PowerGrip® TruMotion® Timing Belts in 2.032mm or 0.080 inch pitch.
The TruMotion® belt construction utilizes a cream-colored polymer compound reinforced with fiberglass tensile cord and a clean polymer-free nylon tooth facing. The belt can withstand high & low temperature ranges of -40°F to +220°F, has a virtually dust-free operation and is non-marking. The belt also has a high flex life and resistance to elongation. TruMotion® belts have a durable wear surface for longer life and are RoHS compliant.
|
Bushes - Hobby | |
Bushes - Plastic - Hobby
A small selection of popular sizes X-Lube.
See main listings for sizes not shown here. Pricing is highly quantity dependant. Please enquire. Self lubricating - low friction - non-corrosive - light weight - chemical resistance. Molybdenum Disulphide filled Nylon 6.
|
Bushes - Non Metallic | |
Bushes - Plastic - X-Lube
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Cable | |
Cable - Miniature
Nylon coated Stainless Steel.
Recommended that nylon coating is stripped prior to swaging. Sold per 300mm length. Multiple quantities will be supplied in a continuous length up to 3mtr maximum.
|
Chain - Roller - Plastic | |
Sprockets - Roller Chain - Plastic
Nylon - Acetal - With and without bore inserts.
|
Clamps - Syncro - Mounting - Sintered | |
Clamps - Syncro - Mounting - Sintered
Sintered Stainless Steel 316. Screw Treat Per MIL-S-5002, Clamp as cast and tumbled. Insert - Nylon Type 1 per MIL-M20693, Natural Colour.
|
Clamps for Flexiracks | |
Gears - Racks - Flexible - Guide Rails
For mounting flexirack. Flexible nylon or rigid aluminium guide rails.
|
Couplings - Ball | |
Couplings - Ball
High Speed - Up to 15 Degrees Angular Offset. 0.17 to 22.6 N.m Torque. Up to 20,000 rpm.
Speed Ratings :. 20000 RPM at up to 5 Degree Operating Angle. 10000 RPM at 6 to 10 Degree Operating Angle (Torque Reduction 50%). 5000 RPM at 11 to 15 Degree Operating Angle (Torque Reduction 66%). Nylon centred units provide electrical insulation between shafts.
|
Couplings - BoWex - Junior | |
Couplings - BoWex - Junior
Nylon 2 piece and 3 piece couplings. 5 to 24 Nm. 6000 rpm max.
Approved distribution through the Australian Wholesaler (Deanquip). Crowned gear teeth - No need for lubrication. Chemical resistant nylon. Electrically insulated. Grub Screw opposite Keyway.
|
Couplings - Crowned Tooth | |
Couplings - Crowned Tooth Gear Type. 19.55 to 88 Nm. 8500 to 14000 rpm.
Steel hubs with Moulded Nylon Sleeve.
+/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1 Degree Angular Displacement. Free axial movement. High torque / low inertia.
|
Couplings - Hobby | |
Hobby Couplings - Junior
A small selection of nylon junior couplings.
|
Gears - Mitre - US Sizes | |
Gears - Mitre - 16 Pitch
1:1 Ratio. 20 Degree Pressure Angle - Nylon.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 24 Pitch
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 32 Pitch
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 48 Pitch
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass, carbon steel and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Pinion | |
Gears - Spur - 16 Pitch - 14.5 Degree
PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5 Degree Pressure Angle. Nylon.
|
Gears - Spur - 16 Pitch - 20.0 Degree
PCD = No. of Teeth x 1.588mm (1/16 in.). 20 Degree Pressure Angle. Nylon and acetal.
|
Gears - Spur - 24 Pitch - 14.5 Degree
PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5 Degree Pressure Angle. Nylon, brass and carbon steel.
|
Gears - Spur - 24 Pitch - 20.0 Degree
PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel.
|
Gears - Spur - 32 Pitch - 14.5 Degree
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
|
Gears - Spur - 32 Pitch - 20.0 Degree
PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon.
|
Gears - Spur - 48 Pitch - 14.5 Degree
PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
|
Gears - Spur - 48 Pitch - 20.0 Degree
PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon.
|
Gears - Spur - Module 1.50
PCD = No. of Teeth x 1.500mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
|
Gears - Spur - Module 2.00
PCD = No. of Teeth x 2.000mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
|
Gears - Spur - Module 2.50
PCD = No. of Teeth x 2.500mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
|
Gears - Spur - Module 3.00
PCD = No. of Teeth x 3.000mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
|
Gears - Racks - Metric Sizes | |
Gears - Racks - Module 0.40
20 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.50
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.80
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 1.00
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 1.50
20 Degree Pressure Angle. Carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 2.00
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 2.50
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 3.00
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - US Sizes - 14.5 Degree Pressure Angle | |
Gears - Racks - 16 Pitch - 14.5 Degree
14.5 Degree Pressure Angle. Nylon.
Plastic.
|
Gears - Racks - 24 Pitch - 14.5 Degree
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 32 Pitch - 14.5 Degree
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 48 Pitch - 14.5 Degree
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Housings with Integral Bearing | |
Housings - Bearing - Flanged - Bronze Bearing
±5° Static Alignment.
Bearing: Bronze SAE 840 (oil impregnated). Housing: Sintered Aluminium. Bearing Retainer: Outer retainer is steel (which is clinched into Aluminium housing) with a Nylon washer on first face. Apply appropriate factor of safety to the nominal loads and speeds specified. Mating shaft rec. Min. 100 HRB. Max surface finish 16 RMS. Rec. shaft clearance 0.013 - 0.038mm.
|
Spring Assemblies - Bracket - RINO | |
Spring Assemblies - Bracket - RINO
Spring: Stainless Steel 301 S21 Grade. Bobbin and Bracket: Nylon Moulded secured to aluminium sheet. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring. End holes are centred at the distances and diameters shown in the tables.
|
|
