Fishing Reel Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Insert bearings ideal for wet conditions. Similar to standard wide inner ring bearings for P, F, Fl type housings.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30
oC to 100
oC Continuous. This category may be available in the new MBA online store at
Bearings - Acetal - Double Row - with Glass Balls.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30
oC to 100
oC Continuous. This category may be available in the new MBA online store at
Bearings - Acetal - Single Row - with Glass Balls.
Related Information:
PEEK (Polyetheretherketone), is a high temperature, high-performance engineering polymer.
Races made from PEEK - Balls made from 316 Stainless Steel - Cages from PEEK. PEEK offers chemical and water resistance similar to PPS (Polyphenylene Sulfide) but can operate at higher temperatures. PEEK can be used continuously to 338 Deg F (170 Deg C) and in hot water or steam without permanent loss in physical properties. Wear, Chemical & Hydrolysis Resistant. Exceptional performance over a wide range of temperatures and extreme conditions. Low Smoke and Toxic Gas Emission.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from PVDF - Balls made from 316 Stainless Steel - Cages from PVDF. KynarŪ PVDF (Polyvinylidene Fluoride) is a high performance engineering polymer. KynarŪ has provided superior chemical resistance properties in critical contact applications for food, pharmaceutical, and semiconductor industries for over 20 years. For chemical and high temperature resistance, low permeability and high mechanical strength. This category may be available in the new MBA online store at
Bearings - PVDF - Single Row - with Glass Balls.
Related Information:
Brass angle is great for small hobby projects like building scale models or dioramas.
This category may be available in the new MBA online store at
Angle - Brass.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Also known as internal hitch pins, bridge pins or humpback pins
Also known as internal hitch pins, bridge pins or humpback pins
Used with toggle latches series 800, 802, 803 and 806
Heat Sealer Tape
Non stick ptfe tape is resistant to abrasion, high temperature and chemicals. Commonly used on heatsealing machines, mould protection, packaging, automotive and electrical applications. Temperature range minus 73
oC to 260
oC (-100 to 500 Deg F). Less than 5 percent elongation. This category may be available in the new MBA online store at
Tape - Fiberglass - PTFE Coated.
Replacement acetal wheels with glass balls for product moving gravity feed skate conveyors. Plastic skate wheels are ideal for washdown or outdoor applications.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 302 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30
oC to 100
oC Continuous. This category may be available in the new MBA online store at
Bearings - Acetal - Single Row - with 302 Stainless Steel Balls.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30
oC to 100
oC Continuous. This category may be available in the new MBA online store at
Bearings - Acetal - Single Row - with 316 Stainless Steel Balls.
Related Information:
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from PVDF - Balls made from Ground Glass - Cages from PVDF. Kynar -tm- PVDF (Polyvinylidene Fluoride) is a high performance engineering polymer. Kynar -tm- has provided superior chemical resistance properties in critical contact applications for food, pharmaceutical, and semiconductor industries for over 20 years. For chemical and high temperature resistance, low permeability and high mechanical strength. This category may be available in the new MBA online store at
Bearings - PVDF - Single Row - with 316 Stainless Steel Balls.
Related Information:
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 116 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 250 Mpa. Hardness 88 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 oC = 260 Mpa. Hardness 84 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 oC 210 Mpa. Hardness 81 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 oC = 135 Mpa. Hardness 82 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 oC = 73 Mpa. Hardness 74 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 oC = 112 Mpa. Hardness 79 Shore D (DIN53505). Bushing bore tolerance is D11 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 oC = 120 Mpa. Hardness 83 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 oC = 125 Mpa. Hardness 77 Shore D (DIN53505). Bushing bore tolerance is E10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.
Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 oC = 170 Mpa. Hardness 85 Shore D (DIN53505). Bushing bore tolerance is F10 after a H7 press fit. Tolerances listed in the tables are after assembly using H7 recommended fit.
Related Information:
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction. This category may be available in the new MBA online store at
Housings - Bearing - Single Assembly.
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating. This category may be available in the new MBA online store at
Snap Buttons - Single End - Dog Leg.
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating. This category may be available in the new MBA online store at
Snap Buttons - Single End - Spring Leg.
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Simple effective way to lock components onto shafts.
416 Stainless Steel. Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened. This category may be available in the new MBA online store at
Shaftloc-tm Sleeves - Single Ended.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Related Information:
For holding, clamping and positioning work pieces. Body is black oxide steel.
Related Information:
Use with idler shafts and idler pulleys. Fixed base with adjustable arm through 360o.
Related Information:
Levelling adjusters. These industrial glides are an excellent and inexpensive solution for light duty applications such as office furniture, shelving, point of sale displays, cabinetry and small machinery.
Fairloc
tm Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. This category may be available in the new MBA online store at
Hubs - Gear and Dial - Single.
Related Information:
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Small Parts & Bearings Pty Ltd (ABN 79 121 865 414)
Small Parts & Bearings offers 138615
products in 2015 categories including
couplings, screws, hex nuts, ball bearings, roller bearings, thrust bearings, ceramic and hybrid bearings, stainless steel bearings, miniature bearings, shafting, corrosion resistant bearings - see the full listing in the
Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or
cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other
product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully
traceable courier delivery.
Small Parts & Bearings is part of MBA Group offering a select range from the MBA Group catalogue.
Information on this website is Copyright Small Parts & Bearings 1997. All rights reserved.