Gears Metric Stem Categories (Stocked Items Only)


Category Matches

Gears Metric Bevel

TopHide Pictures

Gears - Bevel - Module 0.5 - Plastic
Gears - Bevel - Module 0.5 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1. Acetal.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Bevel - Module 1.5 - Plastic
Gears - Bevel - Module 1.5 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Bevel - Module 1.5 - Steel
Gears - Bevel - Module 1.5 - Steel

Search Rating: 100%

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Bevel - Module 1 - Plastic
Gears - Bevel - Module 1 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Bevel - Module 2 - Plastic
Gears - Bevel - Module 2 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears Metric Mitre

TopHide Pictures

Gears - Mitre - Module 0.8 - Plastic
Gears - Mitre - Module 0.8 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Mitre - Module 1.5 - Brass
Gears - Mitre - Module 1.5 - Brass

Search Rating: 100%

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Mitre - Module 1 - Brass
Gears - Mitre - Module 1 - Brass

Search Rating: 100%

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Mitre - Module 1 - Plastic
Gears - Mitre - Module 1 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Mitre - Module 2 - Plastic
Gears - Mitre - Module 2 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Mitre - Module 3 - Plastic
Gears - Mitre - Module 3 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle - Acetal

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears Metric Racks

TopHide Pictures

Gear Racks - Module 0.3 - Brass
Gear Racks - Module 0.3 - Brass

Search Rating: 100%

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 0.5 - Plastic
Gear Racks - Module 0.5 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Acetal and Nylon

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 0.75 - Brass
Gear Racks - Module 0.75 - Brass

Search Rating: 100%

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 0.8 - Brass
Gear Racks - Module 0.8 - Brass

Search Rating: 100%

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 0.8 - Plastic
Gear Racks - Module 0.8 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Nylon

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 0.8 - Steel
Gear Racks - Module 0.8 - Steel

Search Rating: 100%

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Carbon steel.

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 1 - Plastic
Gear Racks - Module 1 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Acetal and Nylon

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 1 - Steel
Gear Racks - Module 1 - Steel

Search Rating: 100%

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Carbon Steel

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gear Racks - Module 2 - Steel
Gear Racks - Module 2 - Steel

Search Rating: 100%

Also see combined categories:
All Metric Gear Racks
All All Gear Racks

20o Pressure Angle. Carbon steel

Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths. For easy ready selected sets of rack and gear please see the HES website.


Gears Metric Spur

TopHide Pictures

Gears - Spur - Module 0.4 - Brass
Gears - Spur - Module 0.4 - Brass

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.4 - Plastic
Gears - Spur - Module 0.4 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.4 - Stainless
Gears - Spur - Module 0.4 - Stainless

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. 416 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.5 - Aluminium
Gears - Spur - Module 0.5 - Aluminium

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 2024 aluminium

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.5 - Brass
Gears - Spur - Module 0.5 - Brass

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.5 - Plastic
Gears - Spur - Module 0.5 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.5 - Stainless
Gears - Spur - Module 0.5 - Stainless

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.7 - Plastic
Gears - Spur - Module 0.7 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.700mm. 20o Pressure Angle. Acetal.

Metallic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.8 - Aluminium
Gears - Spur - Module 0.8 - Aluminium

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 2024 aluminium

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.8 - Brass
Gears - Spur - Module 0.8 - Brass

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.8 - Plastic
Gears - Spur - Module 0.8 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.8 - Stainless
Gears - Spur - Module 0.8 - Stainless

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 1.25 - Plastic
Gears - Spur - Module 1.25 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. Acetal.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 1.25 - Stainless
Gears - Spur - Module 1.25 - Stainless

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 1.250mm. 20o Pressure Angle. 303 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 1.5 - Plastic
Gears - Spur - Module 1.5 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 1.500mm. 20o Pressure Angle. Acetal and Nylon

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 1 - Plastic
Gears - Spur - Module 1 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 1 - Stainless
Gears - Spur - Module 1 - Stainless

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. 303 stainless steel and 416 stainless steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 2.5 - Steel
Gears - Spur - Module 2.5 - Steel

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 2.500mm. 20o Pressure Angle. Carbon steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 2 - Steel
Gears - Spur - Module 2 - Steel

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 2.000mm. 20o Pressure Angle. AISI4135 carbon steel

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 3 - Plastic
Gears - Spur - Module 3 - Plastic

Search Rating: 100%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 3.000mm. 20o Pressure Angle. Nylon

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears Metric Mitre

TopHide Pictures

Gears - Mitre - Module 1 - Zinc Diecast
Gears - Mitre - Module 1 - Zinc Diecast

Search Rating: 100%

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Mitre - Module 2 - Zinc Diecast
Gears - Mitre - Module 2 - Zinc Diecast

Search Rating: 100%

Also see combined categories:
All Metric Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears Metric Spiral Mitre

TopHide Pictures

Gears - Mitre - Spiral - Module 1.5 - Steel
Gears - Mitre - Spiral - Module 1.5 - Steel

Search Rating: 100%

Also see combined categories:
All Metric Mitre Gears
All Metric Spiral Mitre Gears

1:1 Ratio. 20o Pressure Angle - 35o Spiral tooth - Steel.

A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears Metric Spur

TopHide Pictures

Gears - Spur - Module 0.4 - Plastic with Insert
Gears - Spur - Module 0.4 - Plastic with Insert

Search Rating: 99%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.400mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.5 - Plastic with Insert
Gears - Spur - Module 0.5 - Plastic with Insert

Search Rating: 99%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.500mm. 20o Pressure Angle. Acetal.

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 0.8 - Plastic with Insert
Gears - Spur - Module 0.8 - Plastic with Insert

Search Rating: 99%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 0.800mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 1 - Plastic with Insert
Gears - Spur - Module 1 - Plastic with Insert

Search Rating: 99%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle.Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears - Spur - Module 1 - Plastic with Stainless Hub
Gears - Spur - Module 1 - Plastic with Stainless Hub

Search Rating: 99%

Also see combined categories:
All Metric Spur Gears
All All Spur Gears

PCD = No. of Teeth x 1.000mm. 20o Pressure Angle. Acetal

Metallic and plastic. FairlocTM Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Gears Metric Worms

TopHide Pictures

Worm Gears - Module 0.8 Series 2 - Plastic Gear and Metallic Worm
Worm Gears - Module 0.8 Series 2 - Plastic Gear and Metallic Worm

Search Rating: 97%

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Match with metallic worms Module 0.80 Series 2.

20o Pressure Angle - 4.40o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:

Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Left Hand

Search Rating: 97%

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:

Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand
Worm Gears - Module 1 Series 1 - Plastic and Metallic - Right Hand

Search Rating: 97%

Also see combined categories:
All Worm Gears
All Metric Worm Gears

Worms and Gears must be chosen from the same pitch and series to match.

20o Pressure Angle - 3.58o Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.

Related Information:

Gears Inch Spur

TopHide Pictures

Gears - Spur - 72DP - Stem - Stainless
Gears - Spur -  72DP - Stem - Stainless

Search Rating: 88%

Also see combined categories:
All Imperial Spur Gears
All All Spur Gears

303 stainless steel. DP stands for Diametrical Pitch and is an imperial measurement system.

Metallic. 72 Diametrical Pitch. Approx 1.11mm between teeth. For easy ready selected sets of rack and gear please see the HES website.

Related Information:

Leadscrews

TopHide Pictures

Leadscrews - Metric - Rolled Thread - Carbon Steel
Leadscrews - Metric - Rolled Thread - Carbon Steel

Search Rating: 61%

Also see combined categories:
All Metric Leadscrews

Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.

Carbon Steel C35. For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.

Related Information:

Pins Taper

TopHide Pictures

Pins - Taper - Metric - Carbon Steel
Pins - Taper - Metric - Carbon Steel

Search Rating: 61%

Also see combined categories:
All Taper Pins - Metric
All All Taper Pins

Metric Sizes Tapered 1:50

Metric Sizes to DIN 1.

Related Information:

Pins - Taper - Metric - Extractable - Internal Thread
Pins - Taper - Metric - Extractable - Internal Thread

Search Rating: 61%

Also see combined categories:
All Taper Pins - Metric
All All Taper Pins

Metric Sizes Tapered 1:50 and threaded internally for easy extraction.

DIN 7978. Mild Steel.

Related Information:

Leadscrews

TopHide Pictures

Leadscrew Nuts - Metric - Round - Metallic
Leadscrew Nuts - Metric - Round - Metallic

Search Rating: 61%

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.

Related Information:

Leadscrew Nuts - Metric - Square - Metallic
Leadscrew Nuts - Metric - Square - Metallic

Search Rating: 61%

Also see combined categories:
All Leadscrew Nuts
All Metric Leadscrew Nuts

Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.

Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.

Related Information:

Springs Die

TopHide Pictures

Springs - Die - Metric - Extra Heavy Duty
Springs - Die - Metric - Extra Heavy Duty

Search Rating: 61%

Also see combined categories:
All Metric Die Springs
All All Die Springs

Colour coded yellow

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.


Springs - Die - Metric - Heavy Duty
Springs - Die - Metric - Heavy Duty

Search Rating: 61%

Also see combined categories:
All Metric Die Springs
All All Die Springs

Colour coded red

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.


Springs - Die - Metric - Light Duty
Springs - Die - Metric - Light Duty

Search Rating: 61%

Also see combined categories:
All Metric Die Springs
All All Die Springs

Colour coded green

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.


Springs - Die - Metric - Medium Duty
Springs - Die - Metric - Medium Duty

Search Rating: 61%

Also see combined categories:
All Metric Die Springs
All All Die Springs

Colour coded blue

High tensile strength chromium alloy steels. Heat Resistance: Up to +230oC (Loss of load occurs above +120oC). Spring Ends: Squared and ground. For compressed length, Subtract Deflection from Free Length.


Gears Inch Bevel

TopHide Pictures

Gears - Bevel - 24 Diametrical Pitch - Plastic
Gears - Bevel - 24 Diametrical Pitch - Plastic

Search Rating: 60%

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Bevel - 32 Diametrical Pitch - Plastic
Gears - Bevel - 32 Diametrical Pitch - Plastic

Search Rating: 60%

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Bevel - 48 Diametrical Pitch - Plastic
Gears - Bevel - 48 Diametrical Pitch - Plastic

Search Rating: 60%

Also see combined categories:
All Imperial Bevel Gears

For 90o angle power transfer. Ratios exceeding 1 to 1. Nylon and Acetal.

20o Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears Inch Mitre

TopHide Pictures

Gears - Mitre - 24 Diametrical Pitch - Brass
Gears - Mitre - 24 Diametrical Pitch - Brass

Search Rating: 60%

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Gears - Mitre - 24 Diametrical Pitch - Plastic
Gears - Mitre - 24 Diametrical Pitch - Plastic

Search Rating: 60%

Also see combined categories:
All Imperial Mitre Gears

1:1 Ratio. 20o Pressure Angle - Nylon.

Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90o angle. See Gears - Bevel for other ratios. For easy ready selected sets of 90o gears please see the HES website.

Related Information:

Bearings Tapered Roller

TopHide Pictures

Bearings - Tapered Roller - Single Row - Metric
Bearings - Tapered Roller - Single Row - Metric

Search Rating: 59%

Includes cup and cone


Nuts Hex

TopHide Pictures

Nuts - Hexagonal - Aluminium
Nuts - Hexagonal - Aluminium

Search Rating: 59%

Also see combined categories:
All Nuts

METRIC.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.

Related Information:

Screws Security

TopHide Pictures

Screws - Security - Button - Socket
Screws - Security - Button - Socket

Search Rating: 59%

Also see combined categories:
All Security Screws

Metric only.

Use special tool listed under Screws - Security - Socket - Tools..

Related Information:

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Screws - Security - Button - Socket.

Pinion Wire Imperial

TopHide Pictures

Gears - Pinion Wire - 32 Diametrical Pitch
Gears - Pinion Wire - 32 Diametrical Pitch

Search Rating: 59%

Also see combined categories:
All Imperial Pinion Wire

Brass and carbon steel.

Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths.


Gears - Pinion Wire - 64 Diametrical Pitch
Gears - Pinion Wire - 64 Diametrical Pitch

Search Rating: 59%

Also see combined categories:
All Imperial Pinion Wire

Brass and carbon steel.

Please note that very thin pinion wire may not be supplied perfectly straight. Pinion wire is meant to be cut into much smaller pieces to make pinion gears so the slight bends in the long length will have no effect on the intended use. Lengths longer than 1mtr can only be shipped internationally using Express not post. Please do not select post at checkout for long lengths.


Screws Security

TopHide Pictures

Screws - Security - Socket - Countersunk - Stainless
Screws - Security - Socket - Countersunk - Stainless

Search Rating: 59%

Also see combined categories:
All Security Screws

Metric only.

Use special tool listed under Screws - Security - Socket - Tools..

Related Information:

Allthread

TopHide Pictures

Threaded Rod - Allthread - Plastic
Threaded Rod - Allthread - Plastic

Search Rating: 59%

Also see combined categories:
All Threaded Rod

UNC - UNF - METRIC - Nylon and PVC. Also known as booker rod.

Light Weight. Non Corrosive. Vibration Resistant.


If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Threaded Rod - Allthread - Plastic.

Circlips

TopHide Pictures

Circlips - External - Standard - Berryllium Copper
Circlips - External - Standard - Berryllium Copper

Search Rating: 58%

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / N1400 / D1460. Retaining rings. Snap Rings (USA).

Related Information:

Circlips - External - Standard - Carbon Steel
Circlips - External - Standard - Carbon Steel

Search Rating: 58%

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / N1400 / D1460. Retaining rings. Snap Rings (USA).

Plain carbon steel.

Related Information:

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Circlips - External - Standard - Carbon Steel.

Circlips - External - Standard - Stainless Steel
Circlips - External - Standard - Stainless Steel

Search Rating: 58%

Also see combined categories:
All External Circlips

Imperial and metric DIN471 / N1400 / D1460. 420 Stainless Steel. Retaining rings. Snap Rings (USA).

420 Stainless Steel.

Related Information:

Circlips - Internal - Standard - Carbon Steel
Circlips - Internal - Standard - Carbon Steel

Search Rating: 58%

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS. Retaining rings. Snap Rings (USA).

Plain carbon steel. Tolerances on request. Standard and heavy duty options.

Related Information:

Circlips - Internal - Standard - Stainless Steel
Circlips - Internal - Standard - Stainless Steel

Search Rating: 58%

Also see combined categories:
All Internal Circlips

Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS. 420 Stainless Steel. Retaining rings. Snap Rings (USA).

420 Stainless Steel. Tolerances on request. Standard and heavy duty options.

Related Information:

Nuts Hex

TopHide Pictures

Nuts - Hexagonal - Brass
Nuts - Hexagonal - Brass

Search Rating: 58%

Also see combined categories:
All Nuts

UNC - UNF - BA - METRIC.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.


If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Nuts - Hexagonal - Brass.

Nuts - Hexagonal - Steel
Nuts - Hexagonal - Steel

Search Rating: 58%

Also see combined categories:
All Nuts

UNC - UNF - BA - METRIC. Plain and Zinc Plated.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.


Nuts - Hexagonal - Titanium - CP Grade 1
Nuts - Hexagonal - Titanium - CP Grade 1

Search Rating: 58%

Also see combined categories:
All Nuts

Metric Only. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.


Screws Hex Head

TopHide Pictures

Screws - Hex Head - 304 Stainless
Screws - Hex Head - 304 Stainless

Search Rating: 58%

Also see combined categories:
All Machine Screws

Metric - UNF - UNC

Nuts sold seperately - See Nuts.

Related Information:

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Screws - Hex Head - 304 Stainless.

Screws Large Head

TopHide Pictures

Screws - Large Shallow Head - Steel
Screws - Large Shallow Head - Steel

Search Rating: 58%

Metric only

Related Information:

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Screws - Large Shallow Head - Steel.

Allthread

TopHide Pictures

Threaded Rod - Allthread - Steel - Plain
Threaded Rod - Allthread - Steel - Plain

Search Rating: 58%

Also see combined categories:
All Threaded Rod

UNC - UNF - METRIC - BSW - Includes plain mild steel and high tensile. Also known as booker rod.


If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Threaded Rod - Allthread - Steel - Plain.

Shaft Extenders and Reducers

TopHide Pictures

Reducers - Bore
Reducers - Bore

Search Rating: 58%

Inch to Metric / Inch to Inch / Metric to Metric. Brass reducing bushes.

S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub.

Related Information:

Circlips

TopHide Pictures

E-Clips - Basic - Berrylium Copper
E-Clips - Basic - Berrylium Copper

Search Rating: 58%

Also see combined categories:
All E-Clips

Basic imperial and metric e-clips DIN6799 and N1500. Berrylium Copper.

Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip.

Related Information:

E-Clips - Basic - Carbon Steel
E-Clips - Basic - Carbon Steel

Search Rating: 58%

Also see combined categories:
All E-Clips

Basic imperial and metric e-clips DIN6799 and N1500. Carbon spring steel including zinc plated and plain.

Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip. Includes plain and zinc plated.

Related Information:

E-Clips - Basic - Stainless Steel
E-Clips - Basic - Stainless Steel

Search Rating: 58%

Also see combined categories:
All E-Clips

Basic imperial and metric e-clips DIN6799 and N1500. Stainless Steel PH15-7.

Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip.

Related Information:

Nuts Hex

TopHide Pictures

Nuts - Hexagonal - Half - Stainless Steel
Nuts - Hexagonal - Half - Stainless Steel

Search Rating: 58%

Also see combined categories:
All Nuts

UNC - UNF - METRIC

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.


Nuts - Hexagonal - Stainless Steel
Nuts - Hexagonal - Stainless Steel

Search Rating: 58%

Also see combined categories:
All Nuts

UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.


Screws Cap Head

TopHide Pictures

Screws - Cap - Socket - Nylon
Screws - Cap - Socket - Nylon

Search Rating: 58%

Also see combined categories:
All Socket Cap Screws
All Plastic Screws

UNC - UNF - METRIC - Non Conductive - Non Magnetic.

Related Information:

Screws - Low Head - Socket
Screws - Low Head - Socket

Search Rating: 58%

Also see combined categories:
All Machine Screws
All Socket Cap Screws

UNC - UNF - METRIC - Alloy Steel.

Note. Hex key size may. The size listed is the usual and minimum size.

Related Information:

Screws Cheese Head

TopHide Pictures

Screws - Fillister Head - 304 Stainless - Slotted
Screws - Fillister Head - 304 Stainless - Slotted

Search Rating: 58%

Also see combined categories:
All Machine Screws

Metric - UNC - UNF

Nuts sold seperately - See Nuts. DIN 84.

Related Information:

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Screws - Fillister Head - 304 Stainless - Slotted.

Screws - Fillister Head - 316 Stainless - Slotted
Screws - Fillister Head - 316 Stainless - Slotted

Search Rating: 58%

Also see combined categories:
All Machine Screws

Metric - UNC - UNF

Nuts sold seperately - See Nuts. DIN 84.

Related Information:

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Screws - Fillister Head - 316 Stainless - Slotted.

Screws Countersunk

TopHide Pictures

Screws - Countersunk - Brass - Slotted
Screws - Countersunk - Brass - Slotted

Search Rating: 58%

Also see combined categories:
All Countersunk Screws

Flat Head Countersunk METRIC and BSW

Nuts sold seperately - See Nuts.

Related Information:

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Screws - Countersunk - Brass - Slotted.

Screws - Countersunk - Stainless - Pozidrive
Screws - Countersunk - Stainless - Pozidrive

Search Rating: 58%

Also see combined categories:
All Countersunk Screws

Flat Head Countersunk. Metric small selection only.

Nuts sold seperately - See Nuts.

Related Information:

If the product ranges shown on this site are a bit overwhelming you might find a smaller condensed range on the Hobby and Engineering website. See if Hobby & Engineering have smaller hobby ranges of Screws - Countersunk - Stainless - Pozidrive.

Screws Pan Head

TopHide Pictures

Screws - Pan Head - 316 Stainless - Pozidrive
Screws - Pan Head - 316 Stainless - Pozidrive

Search Rating: 58%

Also see combined categories:
All Machine Screws

Metric Only

Nuts sold seperately - See Nuts.

Related Information:

Screws Round Head

TopHide Pictures

Screws - Round Head - 304 Stainless - Slotted
Screws - Round Head - 304 Stainless - Slotted

Search Rating: 58%

Also see combined categories:
All Machine Screws

Metric Only

Nuts sold seperately - See Nuts.

Related Information:

Allthread

TopHide Pictures

Threaded Rod - Allthread - Stainless Steel - 304
Threaded Rod - Allthread - Stainless Steel - 304

Search Rating: 58%

Also see combined categories:
All Threaded Rod

UNC - UNF - METRIC - 303 and 304 grades. Also known as booker rod.


Threaded Rod - Allthread - Stainless Steel - 316
Threaded Rod - Allthread - Stainless Steel - 316

Search Rating: 58%

Also see combined categories:
All Threaded Rod

UNC - UNF - METRIC - 316 grade. Also known as booker rod.



Show all items starting with
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   1   2   3   4   5   6   7   8   9  





Other Store Pages

Click Page Banner Below

Top

Main Pages

Click Page Banner Below

Top





Top



Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 124193 products in 3081 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts and Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.