Categories that include the terms: CHROME and SHAFT
|
Shaft and Shafting |  |
Shafting - Ground - Precision (Relevance 8/10)
Precision ground shafting. Various materials including silver steel, 303 304 316 416 stainless steel, hardened carbon steel, chrome vanadium alloy.
|
Balls | |
Balls - Chrome Steel (Relevance 7/10)
Hardness: Rockwell C: 60-70.
Tolerances available on request. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.
|
Clamping and Locking | |
Clamps - Shaft (Relevance 7/10)
Mild Steel: 045M10. Stainless Steel: 303S21.
|
Collars - Shaft - Clamp Type (Relevance 7/10)
|
Collars - Shaft - Fairloc (Relevance 7/10)
|
Collars - Shaft - Fastlock (Relevance 7/10)
No tools required.
Usable for Nonhardened Shafts. Inner body and Outer sleeve: 303 Stainless, Balls: 440C Stainless, Spring: 302 Stainless.
|
Collars - Shaft - Gripfast (Relevance 7/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Collars - Shaft - Hinged Type - Hex (Relevance 7/10)
|
Collars - Shaft - Hinged Type - Round (Relevance 7/10)
Precision machined. Convenient easy-to-assemble design.
Same axial load handling capabilities as standard two piece collars. Captive clamp screw eliminates lost screws. The collars have a smooth I.D., O.D. & sides with no protruding pins or screws. Easily Machinable / Open Completely. Non-marring / Use on hardened shafts / Use on tubing / Use on split hubs.
|
Collars - Shaft - Standard (Relevance 7/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Collars - Shaft - Stroke Adjustment (Relevance 7/10)
Recommended tolerances for mating shaft diameter : h6. Use with rubber washers listed under WASHERS.
|
Collars - Shaft - With Integral Shim (Relevance 7/10)
Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.
|
Shaft Locks - Potentiometer (Relevance 7/10)
|
Clutches and Brakes | |
Clutches - Shaft Mounted (Relevance 7/10)
24 V DC - Zero Backlash Armature - For parallel loads.
This basic information is designed to assist you to make a decision on which clutch to use. Full dimensions available on request.
|
Clutches - Slip - Magnetic Particle - Integral Shaft - No Power (Relevance 7/10)
Requires no power.
Sealed from contamination. Uses permanent magnets and magnetic particles. Constant torque levels. Zero maintenance - Long operational life. See PDF sheet at bottom of this page.
|
Couplings | |
Couplings - Clutch - Shaft Mounted (Relevance 7/10)
0.565 to 14 N.m. For in-line loads.
24 Volt DC. Zero Backlash Armature. For in-line loads. Dynamic torque is 80% of static torque. 0.565 N.m Models have no keyway in rotor.
|
Extenders - Shaft (Relevance 7/10)
Miniature and large shaft extenders.
|
Fasteners | |
Threaded Rod - Allthread - Brass (Relevance 7/10)
UNC - UNF - METRIC brass.
|
Threaded Rod - Allthread - Plastic (Relevance 7/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Threaded Rod - Allthread - Stainless Steel (Relevance 7/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Threaded Rod - Allthread - Steel (Relevance 7/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Threaded Rod - Aluminium (Relevance 7/10)
UNC and UNF light weight aluminium.
|
Frame Kits | |
Automat - Frame Kit Threaded Rods (Relevance 7/10)
All M3.5 Thread. See PDF file in FTP Directory for more information. Educational tool suitable for mechanical teaching institutions.
All M3.5 Thread Mild Steel.
|
Gearboxes | |
Gearboxes - Output Shafts (Relevance 7/10)
For use in Cross Axis gearboxes with bores. P and PF Series.
Stainless 303 shaft. Steel keys and circlips. P-X and P-DX types suitable for P and PF type gearboxes (cross axis types).
|
Linear Ball Splines | |
Linear Ball Splines - Shaft (Relevance 7/10)
Use with either flanged or unflanged Linear Ball Spline Bearings.
|
Linear Shaft | |
Shafting - Linear - Square (Relevance 7/10)
|
Magnets | |
Magnets - Alcomax - Cylindrical Bar (Relevance 7/10)
No keepers
|
Magnets - Alcomax - Rectangular Bar (Relevance 7/10)
No keepers
|
Magnets - Alnico - Bar (Relevance 7/10)
Cast Alnico 5 bar
|
Magnets - Alnico - Rod - Sintered (Relevance 7/10)
|
Materials | |
Bar - H Section - Brass (Relevance 7/10)
|
Bar - I Beam - Brass (Relevance 7/10)
|
Hexagonal Bar - 303 Stainless (Relevance 7/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Hexagonal Bar - Brass (Relevance 7/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small A/F sizes may not be perfectly straight.
|
Hexagonal Bar - Carbon Steel (Relevance 7/10)
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Rectangular Bar - Aluminum (Relevance 7/10)
Thin and thick Aluminum strip and rectangular profiles
Small sizes may not be perfectly straight.
|
Rectangular Bar - Brass (Relevance 7/10)
Thin and thick brass strip and rectangular profiles
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small sizes may not be perfectly straight.
|
Rod - Drill Blanks (Relevance 7/10)
Made of hardened high speed steel.
Useful for turning and boring tools, constructing pins, hinge pins, arbors, pin gauges, dowels, preforating punchs. Can also be ground to make special cutting tools such as mills, spotfaces, angle or radii cutters, etc.
|
Rod - Round - Acetal (Relevance 7/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Aluminium (Relevance 7/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Brass (Relevance 7/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Bronze - LG2 (Standard) (Relevance 7/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Carbon Fibre (Relevance 7/10)
High impact light weight carbon fibre for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Rod - Round - Glass Fibre (Relevance 7/10)
High impact light weight glass fibre for modelling.
Glass fibre rod is not smooth.
|
Rod - Round - Nylon (Relevance 7/10)
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - PTFE (Relevance 7/10)
Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Polyester PETP (Relevance 7/10)
High mechanical strength, stiffness and hardness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.39 g/cm3 - Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 90 Mpa. Hardness 96 Rockwell M. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Sintered Bronze (Relevance 7/10)
Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight.
|
Rod - Round - Stainless Steel (Relevance 7/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
|
Rod - Round - Urethane (Relevance 7/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Diameter +/- 2 percent
|
Square Bar - 303 Stainless (Relevance 7/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Square Bar - Brass (Relevance 7/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Smaller sizes may not be supplied straight.
|
Square Bar - Carbon Steel (Relevance 7/10)
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Square Bar - Urethane (Relevance 7/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Length +/- 2 percent
|
Rod Ends | |
Rod Ends - Heavy Duty - Ball (Relevance 7/10)
With integral self aligning ball bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20șC to +120șC.
|
Rod Ends - Heavy Duty - Ball - Enlarged Eye (Relevance 7/10)
With integral self aligning ball bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20șC to +120șC.
|
Rod Ends - Heavy Duty - Ball - Reduced Eye (Relevance 7/10)
With integral self aligning ball bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20șC to +120șC.
|
Rod Ends - Heavy Duty - Roller (Relevance 7/10)
With integral self aligning roller bearing.
With grease nipple. Housing: Tempered forged steel. Bearing Race: Case hardened. Thread: Rolled - Surface galvanised. Inner Ring: Ball bearing steel. Hardened, ground. Lubrication: Calcium Complex Soap Grease temperature range -20șC to +120șC.
|
Rod Ends - Plastic (Relevance 7/10)
Thermoplastic Body / L280ź Polymer Ball.
Dimensions not shown are available on request.
|
Rod Ends - Stainless Steel - Nylon Raceway (Relevance 7/10)
|
Rod Ends - Stamped (Relevance 7/10)
Economy stamped style combines high strength with low cost
Made from low carbon steel and plated for corrosion resistance. Ball is case hardened.
|
Rod Ends - Steel - Bronze Lined (Relevance 7/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
Rod Ends - Steel - Nylon Raceway (Relevance 7/10)
|
Rod Ends - Steel - PTFE Lined (Relevance 7/10)
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon steel and Stainless Steel.
Dimensions not shown are available on request.
|
Rod Ends - Steel - PTFE Liner (Relevance 7/10)
|
Rod Ends - Studded - Male-Female - Nylon (Relevance 7/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Rod Ends - Studded - Male-Female - PTFE (Relevance 7/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Rod Ends - Studded - Male-Female - Quick Disconnect (Relevance 7/10)
Joints are strength, quick disconnect assemblies with good wear characteristics. Retaining sleeve insures the assembly can only be put together with the sleeve positively aligned with the ball cavity. When spring is released, alignment is automatic thereby eliminating any possiblity of partial closure. Ball stud and Body are made of low carbon steel. Studs are surface hardened. All Parts are plated and dichromate treated.
|
Rod Ends - Studded - Male-Female - Swaged Construction (Relevance 7/10)
Designed for heavy duty service, they come with dirt shield to provide protection against contaminants.
Unique assembly swages metal to retain the ball in cavity resulting in increased pull out and wear resistance. Ball studs are surface hardened. Made of low carbon steel, plated and dichromate treated.
|
Rod Ends - Studded - Male-Male - Nylon (Relevance 7/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Rod Ends - Studded - Male-Male - PTFE (Relevance 7/10)
Housing is plated and dichromate treated steel. Ball is case hardened and plated Stud is permanently affixed and made from heat treated alloy steel, zinc plated.
|
Shaft and Shafting | |
Rail Supports - With Shaft (Relevance 7/10)
Includes shaft.
Includes shaft to h6 tolerances.
|
Rail Supports - Without Shaft (Relevance 7/10)
For mounting of shafting.
Shafting sold separately.
|
Rod - Drill (Relevance 7/10)
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight.
|
Shafting - Aluminium (Relevance 7/10)
Drylin aluminium shafting is recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40”m. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.
|
Shafting - Ground - Hobby (Relevance 7/10)
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc Not recommended for use with precision steel or stainless steel bearings Some sizes have special features such as serrations or small barbs (noted in description). Unground ends Ideal for axles in robotic applications and educational projects
|
Shafting - Keyed (Relevance 7/10)
Keyways are cut full length of each bar.
Diameter Tolerance +0.05/-0.00 Keyway Depth Tolerance +0.41/-0.00 Keyway Width Tolerance +0.05/-0.00
|
Shafting - Pipe - AISI52100 Steel (Relevance 7/10)
AISI 52100 Steel Hardened to HRC 58-62. Straightness 0.0003 mm / mm. Ideal for design weight reduction. Note! ID of pipe shaft may be up to 1mm undersize. Other lengths may be available on request however a surcharge for special sizing will apply and extended delivery times can be expected (if available).
|
Shafting - Pipe - Aluminium (Relevance 7/10)
Recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40”m. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2
|
Shafting - Pre Drilled for Rail Supports (Relevance 7/10)
Straightness: 0.1 mm / mtr.
|
Shafting - Supported - Pre-Drilled - Aluminium (Relevance 7/10)
For Drylin Bearings.
Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40”m. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2
|
Shafts - Flexible - Coupling Ends - Cased (Relevance 7/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Coupling Ends - Open (Ondrives) (Relevance 7/10)
Hubs: 220 MO7 / Shaft: Steel.
|
Shafts - Flexible - Coupling Ends - Open (SDP) (Relevance 7/10)
Flexible shafting with coupling ends ready to attach to a fixed shaft.
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Panel Mount - Cased (Relevance 7/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Panel Mount - Open (Relevance 7/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Pinion (Relevance 7/10)
|
Supports - Block (Relevance 7/10)
For linear shafting.
Material: Aluminium.
|
Supports - Flanged Four Bolt (Relevance 7/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Supports - Flanged Two Bolt (Relevance 7/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Supports - Pedestal Two Bolt (Relevance 7/10)
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
|
Spacers | |
Joints - Tee - Tubing and Rod (Relevance 7/10)
Inexpensive nylon joiners for hobby tubing and rod
|
Splined Shafts and Bushes | |
Splined Bushes - Flanged (Relevance 7/10)
Steel C45 (080M46) : ISO 14 (DIN 5463) Medium Series. Phosphor Bronze : ISO 14 (DIN 5463) Medium Series. Machinable. (Tolerances do not follow ISO 14 Standard). Steel on Steel is not meant for sliding applications. Steel on Bronze is OK for intermittent sliding under load.
|
Splined Bushes - Unflanged (Relevance 7/10)
Match with same size External splined shafts.
Match bushes and shafts by Major Diameter.
|
Splined Shafts (Relevance 7/10)
Match with same size internal splined bushes.
Match bushes and shafts by Major Diameter.
|
Splines - Ball - Telescoping (Relevance 7/10)
|
Clamping and Locking | |
Shaftloc-tm Clamp Type A (Relevance 3/10)
Simple effective component clamping
Passivated 416 Stainless Steel Simple two part screw together system clamps parts securely together. Vibration resistant. Employing a special asymetric thread to self-lock when the nut encounters resistance. The nut turns freely until it contacts the parts being clamped together. Additional turns wedge the parts into a locked and vibration resistant condition.
|
Shaftloc-tm Simple Type M (Relevance 3/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Double Ended (Relevance 3/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Shaftloc-tm Sleeves - Single Ended (Relevance 3/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Couplings | |
Couplings - Flexible-Shaft Type (Relevance 3/10)
Nonmagnetic flexible shaft couplings. Max torque 0.39 Nm.
Maximum Torque 0.39 N.m (3.5 lb.in). Minium operating radius 89 mm (3.5 in.). Torsional deflection 1.8 Deg per lb.in per inch (25mm) of shaft in Winding Direction. Torsional deflection 2.6 Deg per lb.in per inch (25mm) of shaft in Unwinding Direction. Cadmium Plated Brass Ends - Phosphor Bronze Cable - 300 Series Stainless Screws.
|
Pulleys | |
Pulleys - Synchromesh (Relevance 3/10)
|
Rope and Cable | |
Attachments - Eyes - Synchromesh (Relevance 3/10)
Recommended dimensions after crimping:. 1.05 Cable - A=2.59. 2.06 Cable - A=2.64. 2.60 Cable - A=2.72. 3.40 Cable - A=2.80 (3.40 Cable must have outer helical wire removed prior to crimping).
|
Attachments - Plugs - Synchromesh (Relevance 3/10)
Recommended dimensions after crimping:. 1.05 Cable - A=2.81 B=6.98. 2.06 Cable - A=2.95 B=6.94. 2.60 and 3.40 Cable - A=3.05 B=6.86.
|
Attachments - Thimbles - Synchromesh (Relevance 3/10)
Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends.
|
Cable - Synchromesh (Relevance 3/10)
Pitch Error ±0.050 mm. Cumulative Pitch Error ±4.070 mm max. over 100 pitches. Temperature Range = -30 Deg. Celcius to +80 Deg. Celcius. Avoid strong acids, alkalies and organic solvents.
|
Balls | |
Balls - Bored - Plastic (Relevance 1/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Balls - Bored - Steel (Relevance 1/10)
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
|
Bearings | |
Bearings - Ball - Single Row - Radial - Flanged (Relevance 1/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 1/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - Specialty | |
Bearings - Ball - 316 Stainless Steel (Relevance 1/10)
Food and Medical grade Stainless Steel - Non Hardenable.
Tolerances differ from standard bearing types - see below. Due to the tolerance range it is recommended that each actual bearing is measured to calculate fits. ID +0.0762 mm / -0.000 mm OD +0.000 mm / -0.0762 mm Width +/- 0.127 mm. Rings machined from solid rod stock producing true running concentric bearings. Low load, low speed applications requiring maximum corrosion resistance. Polymer cages, grade 200 type 316 stainless balls, AISI 316 stainless races.
|
Bearings - Ball - Single Row - Radial - Flanged - High Precision (Relevance 1/10)
Stainless and Chrome Steel Bearings with Flanges - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 1/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - Ball - Textile Industry (Relevance 1/10)
Special Design Stainless and Chrome Steel Bearings for the Textile Industry.
Bearings in this category often have special features. Not all Bearings are readily available. Please enquire. Designed for use in textile industry machinery.
|
Bearings - One Way - Roller (Relevance 1/10)
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 1/10)
Retainer : Carbon Steel / Zinc Plated or Oxycoteź Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 1/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycoteź Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze (Relevance 1/10)
Self lubricating. -28 to +95 Deg C. Use any shaft material with 0.8 um or finer finish. Self aligning +/- 5 Degress.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 1/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycoteź Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Clamping and Locking | |
Assemblies - Locking - Flanged (Relevance 1/10)
Suitable for locking sprockets, pulleys, eccentric shafts.
Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. Flange eliminates axial movement of secured component. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub.
|
Assemblies - Locking - Unflanged (Relevance 1/10)
Suitable for locking sprockets, pulleys, eccentric shafts.
Locks components with a bore of (D) to shafts with a diameter of (d). C60 Steel (060A62). Outer ring expands whilst inner ring contracts. During tightening of the screws, the hub must be able to perform axial movement. Clearance h8 / H8. Surface roughness Rt max 10um shaft / hub.
|
Bushings - Integral Taper (Relevance 1/10)
Stainless Steel Taper Bushings.
Will not mar shafts.
|
Bushings - Locking Hub (Relevance 1/10)
Friction grip construction.
Connects rotating components to shafts. Transmits high torque without keyways. Two styles - see diagrams.
|
Clamps - Gear - Two Piece - Commercial Balanced (Relevance 1/10)
Commercial - Stainless - Aluminium - Carbon Steel - For our clamp type gears.
Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. These clamps are designed to clamp the OD of the hub on our clamp type gears. The shaft size listed is for reference only.
|
Clamps - Gear - Two Piece - Precision Balanced (Relevance 1/10)
Precision - Stainless - Aluminium - Carbon Steel - For our clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. These clamps are designed to clamp the OD of the hub on our clamp type gears. The shaft size listed is for reference only.
|
Clamps - Hublock (Relevance 1/10)
Ideal way to attach components to shafts when high torque will be transmitted and a keyway is not disired.
Accommodates large shaft and hub tolerances. Not self centering. Made of alloy steel with black oxide finish for smooth torquing, holding power and surface protection.
|
Collars Threaded - Clamp Type (Relevance 1/10)
Offer full radial holding power without marring the shaft.
|
Grips - Taper (Relevance 1/10)
Duroplastic FS31 black. Axle and threaded bush in Steel. Surface Finish: All edges smoothed and highly polished. To assemble unscrew shaft. The grips fit the disk handwheels with revolving taper grip.
|
Hubs - Gear and Dial - Single (Relevance 1/10)
Fairloc Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Clutches and Brakes | |
Brakes - Magnetic - Particle (Relevance 1/10)
Zero Backlash - Low Inertia - No Friction Surface.
24 V DC. Shaft becomes coupled to housing with electrical excitation. Torque is proportional to the DC input current.
|
Clutch Brakes - Magnetic - Bu-Ord Size 11 (Relevance 1/10)
Breakaway Torque (Energised) at 24-28 V DC : 10.8g.cm (0.15 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 3.6g.cm (0.05 oz.in). Shafts A & B coupled when energised, B shaft braked when de-energised. Inertia (De-Energised) at 24-28 VDC : 2.38g.cm sq (0.013 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.3g.cm sq (0.029 oz.in sq).
|
Clutch Brakes - Magnetic - Bu-Ord Size 11 - Reverse Acting (Relevance 1/10)
Breakaway Torque (Energised) at 24-28 V DC : 18g.cm (0.25 oz.in). Breakaway Torque (De-energised) at 24-28 V DC : 7.2g.cm (0.10 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 7.4g.cm sq (0.041 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.1g.cm sq (0.028 oz.in sq).
|
Clutch Brakes - Magnetic - Bu-Ord Size 18 (Relevance 1/10)
Breakaway Torque (Energised) at 24-28 V DC : 14.4g.cm (0.20 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 2.2g.cm (0.03 oz.in). Shafts A & B coupled when energised, B shaft braked when de-energised. Inertia (Energised) at 24-28 VDC : 5.11g.cm sq (0.071 oz.in sq). Inertia (Energised) at 24-28 VDC : 7.56g.cm sq (0.105 oz.in sq).
|
Clutch Brakes - Magnetic - Bu-Ord Size 18 - Reverse Acting (Relevance 1/10)
Breakaway Torque (Energised) at 24-28 V DC : 3.6g.cm (0.05 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 14.4g.cm (0.2 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 7.27g.cm sq (0.101 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.11g.cm sq (0.071 oz.in sq).
|
Clutches - Friction - Slip Ease (Relevance 1/10)
ADJUSTABLE TORQUE - For shaft to shaft coupling. Set screw housings in both housing and cartridge. SLIP-EASE utilises an axial loaded multi-plate design. For applications where space is at a premium and low backlash is required. Backlash of 2° as standard.
|
Clutches - Magnetic - Bu-Ord Size 11 (Relevance 1/10)
Breakaway Torque (Energised) at 24-28 V DC : 10.8g.cm (0.15 oz.in). Breakaway Torque (De-Energised) at 24-28 V DC : 3.6g.cm (0.05 oz.in). Shafts A & B coupled when energised, braked when de-energised. Inertia (De-Energised) at 24-28 VDC : 0.94g.cm sq (0.013 oz.in sq). Inertia (Energised) at 24-28 VDC : 2.09g.cm sq (0.029 oz.in sq).
|
Clutches - Magnetic - Bu-Ord Size 11 - Reverse Acting (Relevance 1/10)
Breakaway Torque (Energised) at 24-28 V DC : 18g.cm (0.25 oz.in). Breakaway Torque (De-energised) at 24-28 V DC : 7.2g.cm (0.10 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 7.4g.cm sq (0.041 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.0g.cm sq (0.028 oz.in sq).
|
Clutches - Magnetic - Bu-Ord Size 18 (Relevance 1/10)
Breakaway Torque (Energised) at 24-28 VDC : 14.4g.cm (0.20 oz.in). Breakaway Torque (De-Energised) at 24-28 VDC : 4.3g.cm (0.06 oz.in). Shafts a & B coupled when energised, braked when de-energised. Inertia (De-Energised) at 24-28 VDC : 2.74g.cm sq(0.038 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.18g.cm sq (0.072 oz.in sq).
|
Clutches - Magnetic - Bu-Ord Size 18 - Reverse Acting (Relevance 1/10)
Breakaway Torque (Energised) at 24-28 VDC : 3.6g.cm (0.05 oz.in). Breakaway Torque (De-Energised) at 24-28 VDC : 14.4g.cm (0.2 oz.in). Shafts A & B coupled when de-energised, braked when energised. Inertia (De-Energised) at 24-28 VDC : 19g.cm sq (0.134 oz.in sq). Inertia (Energised) at 24-28 VDC : 5.18g.cm sq (0.103 oz.in sq).
|
Clutches - Magnetic - Bu-Ord Size 18 - Triplex (Relevance 1/10)
Breakaway Torque (Energised) at 24-28 VDC : 14.4g.cm (0.20 oz.in). Breakaway Torque (De-Energised) at 24-28 VDC : 4.3g.cm (0.06 oz.in). Shafts A & B coupled when energised (terminals 1 and 2). Shafts A & C coupled when energised (terminals 3 and 4). Inertia (Energised) at 24-28 VDC : 19.2g.cm sq (0.108 oz.in sq) either coil, 25.86g.cm sq (0.145 oz.in sq) both coils.
|
Clutches - Magnetic Particle 24VDC (Relevance 1/10)
Ultrafast Responses.
The input shaft becomes coupled to the output shaft with electrical excitation. Shafts have a flat on the end. Soft or fast start.
|
Limit Stops - Electromagnetic (Relevance 1/10)
Adjustable Limits.
Material: Cast aluminium, black anodised. Shaft: Stainless Steel. Ball bearings used throughout. Four miniature single pole double throw switches. Two adjusting screws to permit simple accurate adjustment of the miniature switch actuators.
|
Couplings | |
Couplings - Ball (Relevance 1/10)
High Speed - Up to 15 Degrees Angular Offset. 0.17 to 22.6 N.m Torque. Up to 20,000 rpm.
Speed Ratings :. 20000 RPM at up to 5 Degree Operating Angle. 10000 RPM at 6 to 10 Degree Operating Angle (Torque Reduction 50%). 5000 RPM at 11 to 15 Degree Operating Angle (Torque Reduction 66%). Nylon centred units provide electrical insulation between shafts.
|
Couplings - Neo-Flex (Relevance 1/10)
0.71 to 1.27 Nm.
303 stainless steel with 73 durometer neoprene centre. Shaft to shaft insulation. Torsional vibration isolation. Ribbed style are more flexible than smooth style. Bore Tolerances: +0.025 / -0.000.
|
Couplings - Slip - Spring Wrapped (Relevance 1/10)
Tension control - transmission overload protection. 0.035 to 1.69 Nm.
Coupling is sliped over one shaft and screws tightened. Second shaft is inserted into other end. Loose end of coupling is pulled back about 0.5mm then screws tightened. Serves as a torque limiter as well as a coupling. Long life under continuous slip applications.
|
Fasteners | |
Joints - Clevis - Plastic (Relevance 1/10)
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
|
Nuts - Dome - Steel (Relevance 1/10)
Mild Steel, chrome and zinc plated
|
Nuts - Hexagonal - Locking (Relevance 1/10)
By applying torque to the locking screw, a press fit or wave spring effect is created locking female threads of the locknut to the male threads of the shaft.
Produces a strong metal to metal lock. Locking set screws do not protrude through the face of the threads of the locknut, eliminating damage to shaft.
|
Socket Set Screws - Acetal Tipped (Relevance 1/10)
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Brass Tipped (Relevance 1/10)
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
|
Socket Set Screws - Diamond Knurled Tip (Relevance 1/10)
Grub screws that grip rough shafts.
|
|
