Ball Splines Linear Categories
Category Matches
Ball Splines Linear
TopHide PicturesLinear Ball Splines - Bearings - Unflanged

Search Rating: 100%
Also see combined categories:
All Linear Ball Splines
Use with Linear Ball Spline Shaft.
Linear Ball Splines - Shaft

Search Rating: 100%
Also see combined categories:
All Linear Ball Splines
Use with either flanged or unflanged Linear Ball Spline Bearings.
Linear Slides
TopHide PicturesLinear - Assemblies - Ball Slide - Precision

Search Rating: 50%
These precision ball slides have a typical coefficient of friction of 0.003 and provide straight line accuracy of 0.0005mm per mm of travel.
At load capacity a life of 250 million mm of travel can be expected. The expected life at half load capacity is 2.5 billion mm. Factory preload adjustment prevents sideplay and backlash. Lightweight aluminium carriage and base with high load capacity. Four tapped and threaded carriage holes and counterbored base holes simplify installation and component mounting. Long life, self cleaning ball bearing needs no lubrication. Positional repeatability 0.005mm. Clear anodised finish.
Linear Slide Assemblies - Ball - Pre-Loaded - Compliant

Search Rating: 50%
Also see combined categories:
All Linear Slide Assemblies
Pre-loaded ball slides provide an acceptable level of accuracy of 0.001mm per mm for most linear motion applications. Considerably lower cost than crossed roller slides.
Uses a conventional hardened steel rod raceway and balls. Incorporates an elastomer spine and shock absorbing backup gib. Provides even and continuous preload, whilst minimising the effects of impact and shock. Tolerant to contamination and can operate of millions of cycles without lubrication. 8-32 UNC mounting holes.
Linear Slide Assemblies - Ball - Pre-Loaded - Hard Gib

Search Rating: 50%
Also see combined categories:
All Linear Slide Assemblies
Pre-loaded ball slides provide an acceptable level of accuracy of 0.001mm per mm for most linear motion applications. Considerably lower cost than crossed roller slides.
Hard gib preload. Tolerant to contamination and can operate of millions of cycles without lubrication. 8-32 UNC mounting holes.
Linear Bearings
TopHide PicturesBearings - Linear - Ball - Miniature - Super High Precision

Search Rating: 50%
Also see combined categories:
All Closed Linear Ball Bearings
High Precision Corrosion Resistant Miniature Linear Bearings.
High Precision Swiss Made, Accurate Guiding, Smooth Running. High Load Capacity. Tolerances --- d (+0.008 / -0.000 mm) D (+0.000 / -0.010 mm). Recommended Outer ring fitted with interferance of 1-3 Microns or retained by Circlips. Shafts (not included) should be 60-63 Rockwell C hardness with tolerances +0.000 / -0.006 mm.
Bearings - Linear - Ball - Stainless Steel - Closed

Search Rating: 50%
Also see combined categories:
All Closed Linear Ball Bearings
Standard closed type to run on standard 60HRC shafts with h6 tolerances. For running on shafts fixed at the ends.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 oC Intermittent, 80 Deg C continuous.
Bearings - Linear - Ball - Thomson Precision Steel - Closed

Search Rating: 50%
Also see combined categories:
All Thomson Linear Ball Bearings
For running on shafts fixed at the ends.
Linear Slides
TopHide PicturesSlides - Linear - Recirculating Ball - Standard

Search Rating: 49%
Also see combined categories:
All Linear Slides
The BSR precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants. Note BSR1530SL and BSR2040SL can not be mounted from inside of track rail.
Slides - Linear - Non Recirculating Ball - Standard

Search Rating: 49%
Also see combined categories:
All Linear Slides
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100oC (Constant), +120oC (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
Posi Drive Stage - Ball Slide

Search Rating: 49%
Also see combined categories:
All Posi-Drive Stages
Compact economical Posi Drive Stages take the work out of designing linear motion control systems.
These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.
Linear Slide Assemblies - Cross Roller

Search Rating: 48%
Also see combined categories:
All Linear Slide Assemblies
Higher load capacity than precision ball slide assemblies. High cycling rates. Tolerant of shock and overhanging loads.
Accuracy of 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm. Not as naturally cleaning as ball slides. A good choice for environments protected from dust, and when heavy loads are a consideration. Positive stops prevent over-travel. Rollers improve capacity 8-10 times that of balls. Alternately crossed rollers handle force in any direction. Lightweight aluminium carriage and base. Interchangeable with many types of ball slides. Four tapped carriage holes and two counter bored base holes simplify installation and component mounting.
Ball Screws Rolled
TopHide PicturesBallscrew - Thomson Saginaw

Search Rating: 47%
Also see combined categories:
All Ball Screws
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction. Match all components within the Thomson Saginaw range only.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.
Linear Slides
TopHide PicturesSlides - Drawer - Front Disconnect - Friction - 19mm Ext

Search Rating: 46%
Also see combined categories:
All Drawer Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Friction brake allows drawer to come to a slow stop. Front disconnects by pulling firmly on the drawer until it releases. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Slides - Drawer - Front Disconnect - Lever - Full Ext

Search Rating: 46%
Also see combined categories:
All Drawer Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by lifting a lever lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Slides - Drawer - Front Disconnect - Friction - 19mm Ext - Undercarriage

Search Rating: 46%
Also see combined categories:
All Drawer Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Undercarriage mounted two member slide. Friction brake allows drawer to come to a slow stop. Only one required per drawer. Requires 16 M4 or 8 Gauge Pan Head Screws (not included). Shipped with a bracket and two plastic tracks.
Slides - Drawer - Front Disconnect - Latch Lever - Full Ext

Search Rating: 46%
Also see combined categories:
All Drawer Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Slides - Drawer - Quick Disconnect - Medium Duty - Full Ext

Search Rating: 46%
Also see combined categories:
All Drawer Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide with a quick disconnect.
Slides - Drawer - Stainless - Front Disconnect - Lever - 19mm Ext

Search Rating: 46%
Also see combined categories:
All Drawer Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Positive locking mechanism keeps drawer locked in the open position until actively released. Front disconnects by pressing a drawer latch lever. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - 19mm Ext

Search Rating: 46%
Also see combined categories:
All Drawer Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Slides - Drawer - Stainless - No Disconnect - Heavy Duty - Full Ext

Search Rating: 46%
Also see combined categories:
All Drawer Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.
Slides - Drawer - Stainless - No Disconnect - Medium Duty - 19mm Ext

Search Rating: 46%
Also see combined categories:
All Drawer Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted two member slide. Positive stop slide that will not disconnect once installed. Requires 16 M4 or 8 Gauge Pan Head Screws (not included).
Slides - Drawer - Stainless - No Disconnect - Medium Duty - Full Ext

Search Rating: 46%
Also see combined categories:
All Drawer Slides
Made from 304 stainless with bearing balls. Used where corrosion resistance is required such as laboratories, humid and damp environments, marine applications and clean rooms. Bright finish, tight tolerance, quiet operation and smooth glide.
Side mounted three member slide. Allows drawer to be pulled out further than the slide length allowing full access to the drawer. Positive stop slide that will not disconnect once installed.
Linear Bearings
TopHide PicturesBearings - Linear - Sliding - Stainless - PTFE - Closed

Search Rating: 46%
Also see combined categories:
All Sliding Linear Bearings
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.
Bearings - Linear - Sliding - Stainless - PTFE - Open

Search Rating: 46%
Also see combined categories:
All Sliding Linear Bearings
Stainless steel shell features FDA/USDA compliant, self lubricating PTFE composite liner. Bearings are direct drop in replacements for many inch sized ball bushings.
Able to withstand rapid oscillation, contamination, shock/vibration, wash downs, submersion and shaft brinelling. Stainless steel shell. Designed to run on soft 300 series stainless shafting. Minimum hardness RB25. Ideal for drug and food processing equipment. Unafected by washdowns, contamination and submersion. Coefficient of friction is 0.12 to 0.20. Temperature range is -240 oC to 190 oC. Max static PSI 1000. SFM without any load is 400. Max PV is 10,000.
Linear Slides
TopHide PicturesLinear - Mini Rail - Self-Lubricating - Carriage

Search Rating: 45%
Additional carriages for the Mini-Rail system. Match by rail width.
Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments.
Linear - Mini Rail - Self-Lubricating - Carriage and Rail

Search Rating: 45%
Comes with one carriage. Spare carriages sold separately - match by rail width.
Low profile self-lubricating linear guide system with one piece carriage design. Excellent alternative to linear ball bearing systems. Precision series made from RC70 ceramic coated rail with self lubricating Frelon Gold. Dampens vibration and tolerates shock loads. Will not rust. No metal to metal contact. No balls or rolling elements to trap contamination, skid or damage rail. Operation is consistent, smooth and quiet. Maintenance free. Used in packaging machines, medical equipment, wash-down and harsh environments.
Other Store Pages
Click Page Banner Below
TopMain Pages
Click Page Banner Below
TopTop