Ball Slides And Crossed Roller Positioning Stages Categories


Category Matches

Positioning

TopHide Pictures

Ball Slides and Crossed Roller Positioning Stages
Ball Slides and Crossed Roller Positioning Stages

Search Rating: 61%

Used for Gauging and Positioning Light to Medium Loads.

Spring loaded micrometer drives allow precise repeatable adjustments with low friction and zero backlash. Positioning Slides can be stacked for Multi axis applications. Preloaded positioning slides fully assemebled. Black Anodized Finish.


Linear Slides

TopHide Pictures

Linear Slide Assemblies - Cross Roller
Linear Slide Assemblies - Cross Roller

Search Rating: 52%

Also see combined categories:
All Linear Slide Assemblies

Higher load capacity than precision ball slide assemblies. High cycling rates. Tolerant of shock and overhanging loads.

Accuracy of 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm. Not as naturally cleaning as ball slides. A good choice for environments protected from dust, and when heavy loads are a consideration. Positive stops prevent over-travel. Rollers improve capacity 8-10 times that of balls. Alternately crossed rollers handle force in any direction. Lightweight aluminium carriage and base. Interchangeable with many types of ball slides. Four tapped carriage holes and two counter bored base holes simplify installation and component mounting.


Linear Slide Assemblies - Ball - Pre-Loaded - Compliant
Linear Slide Assemblies - Ball - Pre-Loaded - Compliant

Search Rating: 52%

Also see combined categories:
All Linear Slide Assemblies

Pre-loaded ball slides provide an acceptable level of accuracy of 0.001mm per mm for most linear motion applications. Considerably lower cost than crossed roller slides.

Uses a conventional hardened steel rod raceway and balls. Incorporates an elastomer spine and shock absorbing backup gib. Provides even and continuous preload, whilst minimising the effects of impact and shock. Tolerant to contamination and can operate of millions of cycles without lubrication. 8-32 UNC mounting holes.


Linear Slide Assemblies - Ball - Pre-Loaded - Hard Gib
Linear Slide Assemblies - Ball - Pre-Loaded - Hard Gib

Search Rating: 51%

Also see combined categories:
All Linear Slide Assemblies

Pre-loaded ball slides provide an acceptable level of accuracy of 0.001mm per mm for most linear motion applications. Considerably lower cost than crossed roller slides.

Hard gib preload. Tolerant to contamination and can operate of millions of cycles without lubrication. 8-32 UNC mounting holes.


Linear Slides - Low Profile - Crossed Roller Table - Aluminium
Linear Slides - Low Profile - Crossed Roller Table - Aluminium

Search Rating: 51%

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel
Linear Slides - Low Profile - Crossed Roller Table - Stainless Steel

Search Rating: 51%

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


Linear Slides - Cross Roller Tables - Aluminium
Linear Slides - Cross Roller Tables - Aluminium

Search Rating: 51%

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


Linear Slides - Cross Roller Tables - Steel
Linear Slides - Cross Roller Tables - Steel

Search Rating: 51%

Also see combined categories:
All Crossed Roller Slide Tables

Crossed roller slide tables are factory assembled and ready to install. They use crossed roller bearings to provide very precise linear motion with low friction and high support stiffness for the load.

Applications include precision instruments, office and communications equipment, surface grinders, tool grinders, assembly fixtures and anywhere precise linear positioning is required. Precision ground v grooved ways and rollers provide high accuracy and load capacity. Withstands force in any direction from alternately crossed rollers at 45 deg angles. Straight line accuracy 0.0025mm per 25mm travel (0.0001 inch per inch). 0.0025mm position repeatability. Each table consists of a one piece base, a one piece table and a pair of linear bearings.


Posi Drive Stage - Crossed Roller
Posi Drive Stage - Crossed Roller

Search Rating: 51%

Also see combined categories:
All Posi-Drive Stages

Compact economical Posi Drive Stages take the work out of designing linear motion control systems.

These stages require no alignment of components and install with only 4 standard fasteners. Fitted with anti backlash 9.525mm diameter leadscrews with 2.54mm lead and zero backlash multibeam couplings. NEMA 23 motor mounts. Straight line accuracy up to 0.00254mm per 25.4mm of travel. Repeatability 0.00254mm.


Slides - Linear - Cross Roller Rail
Slides - Linear - Cross Roller Rail

Search Rating: 47%

Also see combined categories:
All Linear Slides

Compact, precision bearings that can support and guide high loads with high accuracy and repeatability, low friction, and low starting force.

Each consists of a pair of hardened steel ways containing 90 deg V grooves and a row of alternately crossed cylindrical rollers. Installed faced to face on smooth flat and accurately parallel, coplanar or perpendicular surfaces. Lubrication required, light grease for low speeds to continuous oil bath/mist for high speeds.


Redi-Rail - Roller Guides
Redi-Rail - Roller Guides

Search Rating: 24%

Match carriage and rail by rail widh

Easy to use systemcan be iunstalled into many applications including packaging, material handling, automation and assembly equipment. A complete unit consists of a roller guide and rail (sold separately). The roller guide is made from 6061-T6 aluminium base with 3 rollers. Rollers made from 52100 hardened steel, lubricated and sealed. Rail made from 6061-T6 aluminium with hardened and ground steel raceways for the rollers to run on.

Related Information:


Show all items starting with
A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   1   2   3   4   5   6   7   8   9  





Other Store Pages

Click Page Banner Below

Top

Main Pages

Click Page Banner Below

Top





Top



Freight Rates
Terms and Conditions
Privacy Policy

Small Parts and Bearings offers 124116 products in 3089 categories including ball bearings, roller bearings, thrust bearings, ceramic and ceramic hybrid bearings, stainless steel bearings, miniature bearings, linear bearings, shafting, oil seals and adhesives - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Small Parts and Bearings is part of MBA Group offering a select range from the MBA Group catalogue.

Small Parts and Bearings products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Small Parts and Bearings 1997. All rights reserved.