Categories for: tension bushings
Like a heavy duty roll pin.
Made of a high carbon spring steel with high elasticity, resilience and wear characteristics. Designed to replace solid steel tubular and cas hardened bushings because they are close tolerance, self-retaining and through hard. Insertion can be easily accomplished with a hammer and drift. Ideal for high load/low-speed operation in articulating or continuous applications.
Bushings - Spherical - Stainless Steel
Stainless Steel
Compensates for axial loads and misalignment.
Steel
Compensates for axial loads and misalignment.
Bushings - Spherical - Steel - With Oil Hole and Wiper Seal
Steel
Compensates for axial loads and misalignment.
Stainless Steel Taper Bushings.
Will not mar shafts.
Friction grip construction.
Connects rotating components to shafts. Transmits high torque without keyways. Two styles - see diagrams.
Bushings - Drill - Lined - Headless
Designed to guide, position, and support the cutting tool in a metalworking jig.
Used with fixed or slip renewable bushings. Permanently pressed into the jig plate creating precise location points.
Bushings - Drill - Press-fit - Headless
Designed to guide, position, and support the cutting tool in a metalworking jig.
Bushings - Stroke Rotary - Miniature
2 to 12mm Shaft Sizes. Can operate in both linear and rotary directions at the same time.
Set includes outer ring, ball cage and shaft. Ball Cage: Brass Balls: Hard Steel / Shaft: Hard Steel Outer Ring: Hard Steel. Temperature: +100°C (Constant), +120°C (Maximum). Stroke: = (L1 - Lb) x 2. Supplied with extreme accuracy with zero to minimum preload.
Bushings - Stroke Rotary - Sealed
Stroke Rotary Bushing series can operate in both linear and rotary directions at the same time.
Material: Carbon Steel. The fit of Stroke Rotary Bushing with shaft and housing is recommend as shown in Table 1 of the diagram. Actual Stroke Length should be less than 80% of max. stroke. Mating Shafts should be HRC58-64. Surface roughness 0.85 or better. Oil holes provided for lubrication.
Plungers - Spring - Striker Bushings
Use with ball or bolt spring plungers for a hard wearing contact area.
Burnished ground hardened steel.
Protects fragile subjects from micro-vibrations and light shocks. Vibration dampening
Bolt not supplied. Collar : Brass. Bushing : Silicone Gel.
Vee grooved track roller bushings.
Stationary bushings have a concentric hole. Adjustable bushings have an eccentric hole allowing positioning of the guide wheel as the bush is turned.
Pulleys - Vee - A / 4L - Single Row - QD Bushing
Cast iron pulleys. QD bushings are used to vary the bore sizes
Pulleys - Vee - B / 5L - Single Row - QD Bushing
Cast iron pulleys. QD bushings are used to vary the bore sizes
For testing the tension on assembled timing belts, vee belts, flat belts etc.
Gauges for testing all types of belts when assembled for correct tension.
Bushes - Aluminium Bronze - Graphite Plug - Flanged
Used for Dies and Molds
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.
Bushes - Aluminium Bronze - Graphite Plug - Unflanged
Used for Dies and Molds
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.
Bushes - Aluminium Bronze - Unflanged
Used for Dies and Molds
ID and OD Tolerance : -0.0000 / +0.0127. Length Tolerance : -1.524 / +0.000.
Bushes - Bronze - Dri-Plane - Flanged
Bronze bearings with a graphite-based dry lubricant built in.
Doesnt require oil or grease for lubrication, therefore, cleaner with no out gassing, can operate between -34 to 371 deg C.
Bushes - Bronze - Sintered - Flanged
Oil impregnated flanged sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
Bushes - Bronze - Sintered - Flanged - Oilite
Genuine Oilite flanged oil impregnated sintered bronze bushes.
Genuine Oilite Sintered Bronze designed to be fitted in H7 housings and f7 shafts. Static Load: 50N per mm Sq. Dynamic Load: 15N per mm sq. Rec Speed Range: 0.3 mtr per second to 0.5 mtr per second. Limit one Pv factor no greater than 1.8 Pv (Pv= N per mm sq x mtr per second).
Bushes - Bronze - Sintered - Unflanged
Oil impregnated sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
Bushes - Bronze - Sintered - Unflanged - Oilite
Genuine Oilite oil impregnated sintered bronze bushes.
Genuine Oilite Sintered Bronze designed to be fitted in H7 housings and f7 shafts. Static Load: 50N per mm Sq. Dynamic Load: 15N per mm sq. Rec Speed Range: 0.3 mtr per second to 0.5 mtr per second. Limit one Pv factor no greater than 1.8 Pv (Pv= N per mm sq x mtr per second).
Solid precision LG2 bronze bushes.
ID Tolerance : -0.0127 / +0.040. OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
Bushes - Bronze - Spherical - Sintered
Spherical OD Oil Impregnated Sintered Bronze Bushes.
ID and OD oversized. Enquire if details required.
Bushes - Plastic - Clip - Bevelled Edge
M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F)
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight.
Bushes - Plastic - Clip - Double Flanged
For use with sheet metal
Low clearance. Maintenance free. Economical. High Precision. High wear resistance. Light weight. M250 Polymer minus 40 Deg C to 80 Deg C (minus 40 Deg F to 176 Deg F).
Bushes - Plastic - Ertalyte TX - Flanged
Self lubricated, high mechanical strength, stiffness and hardness.
Specific Gravity 1.44 g/cm3. Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 76 Mpa. Hardness 94 Rockwell M. High mechanical strength, stiffness and hardness. Self lubricating.
Bushes - Plastic - Ertalyte TX - Unflanged
Self lubricated, high mechanical strength, stiffness and hardness.
Bushes - Plastic - Iglidur A200 - Flanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 deg C = 116 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur A200 - Unflanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 deg C = 116 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur A290 - Flanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 deg C = 250 Mpa. Hardness 88 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur A290 - Unflanged
Food grade for low speeds and direct contact with food and pharmaceuticals.
Specific Gravity 1.39 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 deg C = 250 Mpa. Hardness 88 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur F - Flanged
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 deg C = 260 Mpa. Hardness 84 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur F - Unflanged
Electrically conductive. High Compressive Strength. High Temp. Resistant to Chemicals.
Specific Gravity 1.25 g/cm3. Operating Temp 180 C short term / 140 C long term. Tensile Strength at 20 deg C = 260 Mpa. Hardness 84 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur G - Flanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur G - Unflanged
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur H370 - Flanged
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 deg C = 135 Mpa. Hardness 82 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur H370 - Unflanged
Underwater. High Temp. Chemical Resistant. High mechanical loading and wear resistance.
Specific Gravity 1.60 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 deg C = 135 Mpa. Hardness 82 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur H - Flanged
Underwater performance. High Temp. Chemical Resistance.
Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 deg C = 175 Mpa. Hardness 87 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur H - Unflanged
Underwater performance. High Temp. Chemical Resistance.
Specific Gravity 1.64 g/cm3. Operating Temp 240 C short term / 200 C long term. Tensile Strength at 20 deg C = 175 Mpa. Hardness 87 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur J - Flanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 deg C = 73 Mpa. Hardness 74 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur J - Unflanged
Low Wear - Dry Running - Vibration Dampening - Chemical Resistance.
Specific Gravity 1.49 g/cm3. Operating Temp 120 C short term / 90 C long term. Tensile Strength at 20 deg C = 73 Mpa. Hardness 74 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur M250 - Flanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 deg C = 112 Mpa. Hardness 79 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur M250 - Unflanged
For impact resistance vibration dampening unclean environments.
Specific Gravity 1.14 g/cm3. Operating Temp 170 C short term / 80 C long term. Tensile Strength at 20 deg C = 112 Mpa. Hardness 79 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur P - Flanged
Low water absorption. Low wear. Hgh load.
Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 deg C = 120 Mpa. Hardness 75 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur P - Unflanged
Low water absorption. Low wear. Hgh load.
Specific Gravity 1.47 g/cm3. Operating Temp 200 C short term / 130 C long term. Tensile Strength at 20 deg C = 120 Mpa. Hardness 75 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur Q - Flanged
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 deg C = 120 Mpa. Hardness 83 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur Q - Unflanged
Excellent wear resistance under high load. Resistant to dirt.
Specific Gravity 1.40 g/cm3. Operating Temp 155 C short term / 135 C long term. Tensile Strength at 20 deg C = 120 Mpa. Hardness 83 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur W300 - Flanged
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 deg C = 125 Mpa. Hardness 77 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur W300 - Unflanged
Low co-efficient of friction. High wear resistance. Chemical resistant.
Specific Gravity 1.24 g/cm3. Operating Temp 180 C short term / 90 C long term. Tensile Strength at 20 deg C = 125 Mpa. Hardness 77 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur X - Flanged
Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.
Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 deg C = 170 Mpa. Hardness 85 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur X - Unflanged
Very high temperature. Extreme chemical resistance. High compressive strength. Low water absorption.
Specific Gravity 1.44 g/cm3. Operating Temp 315 C short term / 250 C long term. Tensile Strength at 20 deg C = 170 Mpa. Hardness 85 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur Z - Flanged
High temperature. High thermal resistance. Extreme load. High surface speed.
Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 deg C = 95 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - Iglidur Z - Unflanged
High temperature. High thermal resistance. Extreme load. High surface speed.
Specific Gravity 1.40 g/cm3. Operating Temp 310 C short term / 250 C long term. Tensile Strength at 20 deg C = 95 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
Bushes - Plastic - X-Lube - Flanged
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
Bushes - Plastic - X-Lube - Unflanged
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
Match with same size External splined shafts.
Match bushes and shafts by Major Diameter.
Bushes - Stainless Steel and PTFE - Flanged
Composite bearing material conisting of 3 bonded layers; Steel backing strip bonded with porous sinter bronze interlayer which is impregnated and overlaid with polytetrafluroethylene(PTFE) containing a mixture of inorganic filers and special polymer fibre
Operating Temperature -200 Degrees to 280 Degrees Celsuis. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.
Bushes - Stainless Steel and PTFE - Unflanged
Composite bearing material conisting of 3 bonded layers; Steel backing strip bonded with porous sinter bronze interlayer which is impregnated and overlaid with polytetrafluroethylene(PTFE) containing a mixture of inorganic filers and special polymer fibre
Operating Temperature -200 Degrees to 280 Degrees Celsuis. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.
Bushes - Steel - DP4 Type - Flanged
Composite bearing material conisting of 3 bonded layers; Steel backing strip bonded with porous sinter bronze interlayer which is impregnated and overlaid with polytetrafluroethylene(PTFE) containing a mixture of inorganic filers and special polymer fibre
Operating Temperature -200 Degrees to 280 Degrees Celsuis. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.
Bushes - Steel - DP4 Type - Unflanged
Composite bearing material conisting of 3 bonded layers; Steel backing strip bonded with porous sinter bronze interlayer which is impregnated and overlaid with polytetrafluroethylene(PTFE) containing a mixture of inorganic filers and special polymer fibre
Operating Temperature -200 Degrees to 280 Degrees Celsuis. Low static and dynamic friction coefficient, Suitable for sliding, oscillating, reiprocating and rotating applications. High reistance to be cavitation and flow erosion damage of the polymer bearing surface by the lubricant, Excellent wear resistant. Also suitable for use with non-lubricating fluids and in light duty unlubricated applications, Lead free.
Bushes - Steel - DUB Type - Flanged
Composite bearing material conisting of 3 bonded layers; Steel backing strip bonded with porous sinter bronze interlayer which is impregnated and overlaid with polytetrafluroethylene(PTFE) and lead bearing material.
Operating Temperature -200 Degrees to 280 Degrees Celsuis. Maximum Load 140N/mm2. Requires no lubrication, Maintenance free operation, Exhibits low wear rate, Seizure resistant, High Static and Dynamic Load capacity. Good Frictional properties with negligible stick-slip, Resists Solvents, No water absorption, Compact and light. Electrically conductive and shows no electrostatic effects, Good embedability and is tolerant of dusty environments.Too many choices?
You have selected to see ALL categories including any of the following words: tension bushings
|
| |||||||||||||||||||||||||
| Select all items starting with... | |||||||||||||||||||||||||
| A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Or use the category search | ||||||||||||||||
|
| |||||||||||||||||||||||||
