Categories for: square shaft
For mounting of shafting.
Shafting sold separately.
Includes shaft.
Includes shaft to h6 tolerances.
Ready made precision ground idler shafts.
Internal grease hole can be accessed by drilling if required. Use with your idler pulleys. Can be used with the idler tensioners listed on this site or use in your own design.
Shafts - Flexible - Coupling Ends - Open (SDP)
Flexible shafting with coupling ends ready to attach to a fixed shaft.
See PDF file at bottom of internet page for Performance Data.
Used to maintain radial integrity and eliminate the need for parallel shafting.
Bearings are made from 6061-T6 Aluminum with Anodized finished. Equipped with bearing plugs that run on a single shaft. Threaded adjustable plugs are made from 316 Stainless with self-lubricating FrelonJ wear pads.
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc. Not recommended for use with precision steel or stainless steel bearings. Some sizes have special features such as serrations or small barbs (noted in description). Unground ends. Ideal for axles in robotic applications and educational projects.
Drylin aluminium shafting is recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: ph between 2 and 9.
Recommended for use with Igubal Drylin bearings only.
Material : AlMgSi 0.5 F22. Tolerance: h9 - h11. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Special Electrical Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2
Shafting - Supported - Pre-Drilled - Aluminium
For Drylin Bearings.
Material : AlMgSi 0.5 F22. Roundness: DIN 1798. Straightness: DIN 1798. Hardness: 75HB. Surface: Hard anodised. Oxidisation (wear resistant Al. Oxide) Layer Thickness: >40µm. Surface Hardness: 450-550 HV. Roughness: Ra<0.5. Spec. Electr. Resistance: 4*1011 Ohm mm2/m. Chemical Resistance: 2
Shafting - Ground - Silver Steel
Unhardened silver steel shafting for general purposes. Not suitable for precision bearings until machined to correct tolerances and hardened.
See also drill rod. Drill Rod.
Keyways are cut full length of each bar.
Diameter Tolerance +0.05/-0.00. Keyway Depth Tolerance +0.41/-0.00. Keyway Width Tolerance +0.05/-0.00.
Shafting - Ground - Precision - Chrome Steel
Precision ground shafting. Chrome vanadium alloy. Hardened and recommended for use with precision bearings.
Shafting - Ground - Precision - Stainless 300 Grade
Precision ground shafting. Including 303 and 316 grades.
Shafting - Ground - Precision - Stainless 400 Grade Hardened
Precision ground shafting. 416, 440C and 17-4PH grades. Hardened and recommended for use with precision bearings.
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Smaller sizes may not be supplied straight.
Vibration dampening
Fastener may be steel, brass or zinc plated. Natural rubber isolator.
Match with same size internal splined bushes.
Match bushes and shafts by Major Diameter.
For use in Cross Axis gearboxes with bores. P and PF Series.
Stainless 303 shaft. Steel keys and circlips. P-X and P-DX types suitable for P and PF type gearboxes (cross axis types).
Shafts - Flexible - Coupling Ends - Open (Ondrives)
Bi-directional flexible shaft couplings.
Hubs: 220 MO7 / Shaft: Steel. Standard bored ends. Keyways can be included in the bores for additional cost.
Shafts - Flexible - Masterflex - Size 13 - High Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. High duty with sintered bushes.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 12.7mm encased in 25mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 15mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 13 - Standard Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. Standard Duty with ball bearings.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 12.7mm encased in 25mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 15mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 16 - High Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. High duty with sintered bushes.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 16mm encased in 32mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 16mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 16 - Standard Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. Standard Duty with ball bearings.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 16mm encased in 32mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 16mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 4 - High Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. High duty with sintered bushes.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 3.8mm encased in 10.5mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 4mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 4 - Standard Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. Standard Duty with ball bearings.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 3.8mm encased in 10.5mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 4mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 5 - High Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. High duty with sintered bushes.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 4.75mm encased in 14mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 5mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 5 - Standard Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. Standard Duty with ball bearings.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 4.75mm encased in 14mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 5mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 6 - High Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. High duty with sintered bushes.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 6.35mm encased in 17mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 6mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 6 - Standard Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. Standard Duty with ball bearings.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 6.35mm encased in 17mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 6mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 8 - High Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. High duty with sintered bushes.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 8mm encased in 17.5mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 8mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 8 - Standard Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. Standard Duty with ball bearings.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 8mm encased in 17.5mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 8mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 9 - High Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. High duty with sintered bushes.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 9.52mm encased in 22.5mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 10mm coupling bore. Panel nuts are 4mm wide.
Shafts - Flexible - Masterflex - Size 9 - Standard Duty
Fully encased flexible couplings with either bored ends or panel mounting end nuts. Standard Duty with ball bearings.
Torsional deflection in degrees is listed for 0.1Nm load at 1m length. Cable diameter 9.52mm encased in 22.5mm diameter plastic cover. Choose from clockwise only, anti-clockwise only or bi-directional. 10mm coupling bore. Panel nuts are 4mm wide.
Match with same size External splined shafts.
Match bushes and shafts by Major Diameter.
Couplings - Flexible-Shaft Type
Nonmagnetic flexible shaft couplings. Max torque 0.39 Nm.
Maximum Torque 0.39 N.m (3.5 lb.in). Minium operating radius 89 mm (3.5 in.). Torsional deflection 1.8 Deg per lb.in per inch (25mm) of shaft in Winding Direction. Torsional deflection 2.6 Deg per lb.in per inch (25mm) of shaft in Unwinding Direction. Cadmium Plated Brass Ends - Phosphor Bronze Cable - 300 Series Stainless Screws.
Housings - Bearing - Square - Miniature
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
Housings - Bearing - Flanged - Square - W300
With integral self aligning plain bearing.
Housing : Igumid G. Ball : Highly wear resistant Iglidur W300.
Housings - Bearing - Flanged - Square - Plastic
Use with steel, plastic or stainless steel bearing inserts for plastic housings.
Load and speed capability depend on the bearing used.
Screws - Security - Post Combi Square - Pan Head - Super Zinc
Each 200 pack comes with a Post Combination Driver Bit
Use special tool listed under Screws - Securty - Socket - Tools.
Leadscrew Nuts - Metric - Square - Metallic
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only.
Plastic bungs fit inside square tube.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene.
Hollow square tubing for general hobby applications.
Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
Hollow square tubing for general hobby applications.
Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
Tube - Square - Carbon Fibre - Round Hole
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish. Items marked as Low Grade may have tolerance variations up to 0.2mm.
Tube - Square - Carbon Fibre - Square Hole
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish. Items marked as Low Grade may have tolerance variations up to 0.2mm.
Rubber hardness 60 Duro Standard unless otherwise noted. Vibration dampening
Fastener may be steel, brass or zinc plated. Natural Rubber isolator.
Too many choices?
You have selected to see ALL categories including any of the following words: square shaft
|
| |||||||||||||||||||||||||
| Select all items starting with... | |||||||||||||||||||||||||
| A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Or use the category search | ||||||||||||||||
|
| |||||||||||||||||||||||||
